Advertisement
Quick Links
www.insigniarange.com
Last Modified: 07/10/2015
www.insigniarange.co.uk
INSTALLATION MANUAL
30 Day Technical Support:
01908 226545
GT8002a
(NOTE: This service is only available to customers from the day of delivery,
please have your supplier's details and your postcode to hand before calling)
Replacements Parts:
inside of your warranty contact:
www.insigniarange.co.uk/customerService.aspx
Spares/Replacements Parts:
outside of your warranty
contact 0844 800 3069
ATTENTION INSTALLERS:
These instructions must be
WARRANTY REG NO: __________________________
left with the customer
To claim your full 5 year warranty, register your shower within 90 days of delivery at:
www.insigniarange.co.uk/warrantyreg.aspx. Standard 12 month warranty applies if outside this time period.
Advertisement
Related Manuals for Insignia GT8002a
Summary of Contents for Insignia GT8002a
- Page 1 INSTALLATION MANUAL 30 Day Technical Support: 01908 226545 GT8002a (NOTE: This service is only available to customers from the day of delivery, please have your supplier’s details and your postcode to hand before calling) Replacements Parts: inside of your warranty contact: www.insigniarange.co.uk/customerService.aspx...
- Page 2 www.insigniarange.com Last Modified: 07/10/2015 Contents Introduction Electrical Requirements What’s In The Boxes? Screw Pack Contents Plumbing Requirements Starting The Installation Electric Box Connections Steam Generator Connections Sealing and Water Testing MK117 Control Panel Instructions Help Book Information Part list...
- Page 3 Last Modified: 07/10/2015 Thank you for your recent purchase of an Insignia shower. Please read this booklet with great care to ensure you get the best out of your build and have a shower that will last for many years to come! Like everything, in order to obtain a first class product that will serve you well for many years, the effort and correctness put into the assembly will reflect in the quality of your finish.
- Page 4 www.insigniarange.com Last Modified: 07/10/2015 ASSEMBLY AND SIMPLE PLUMBING THIS PRODUCT BUILD IS RATED SUITABLE FOR DIY PURPOSES PROVIDING THE CUSTOMER IS OF ABOVE AVERAGE SKILLS AND FEELS CONFIDENT IN THEIR ABILITY. ONLY YOU THE CUSTOMER WILL KNOW THIS SO BEFORE ANY ATTEMPT IS MADE TO ASSEMBLY READ THROUGH THE FOLLOWING PAGES IN DETAIL THEN DECIDE.
- Page 5 www.insigniarange.com Last Modified: 07/10/2015 YOU WILL NEED TOTAL ELECTRICAL REQUIREMENTS Voltage Rating 220 -240AC Frequency Rating 50HZ Power Rating 3.0KW Other than steam generator Internal Circuit Voltage is Internal Current Rating 0.17A Your electrical contractor should understand ALL legal requirements of connection before undertaking any work or installation. UNDER NO CIRCUMSTANCES UNDERTAKE THIS YOURSELF!!! Note for electrician.
- Page 6 www.insigniarange.com Last Modified: 07/10/2015 Whilst the next steps show you how to assemble your shower we want to make sure you have a correct build to ensure you get a trouble free shower. Therefore our advice is to follow the instructions and perform a dry run to ensure you are confident with the build and you understand fully how the unit is assembled. When we use the word “DRY RUN”...
- Page 7 Note: In some cases you may have more screws than needed, this is done so you have spares! VERY IMPORTANT Have you got everything? If not please contact the Insignia Support Line on 01908 226545. Remember NEVER book your tradesman until everything has arrived, been checked and is present.
- Page 8 www.insigniarange.com Last Modified: 07/10/2015 Pressure Requirements from your house supply We recommend a bar pressure between 2.5 and 3.4 BAR. If you have a combi boiler system no problem should be experienced. If you have a gravity feed older type installation (hot water tank type usually less than 1 bar) you will almost certainly need a pump.
- Page 9 Once you are happy with the levelling of the tray, you can pull it out to begin the main construction. Step 1 Attach the uprights to the bottom curved rail using the ST55 screws (Thinner rail without Insignia logo on)
- Page 10 www.insigniarange.com Last Modified: 07/10/2015 Step 2 Push the “U Shape” glass seal onto each side of the glass panels prior to insertion into the frames. The next step is to attach both front fixed glass panels. In order to do this take the glass panel and offer it up to the upright as shown by the arrows.
- Page 11 www.insigniarange.com Last Modified: 07/10/2015 Step 4 Run a bead of silicone along the bottom of the back panels and lock the back glass panel to the completed front frame in the position shown in the image marked “1” Once you have met the back panel inside the front upright as per the close up image walk the panel around to the position shown in the image marked “2”...
- Page 12 www.insigniarange.com Last Modified: 07/10/2015 Step 6 Align the roof with your shower walls and using the ST25 screws and SW9 Washers fix the back walls to the roof by screwing upwards from the rear of the shower. NOTE: You will notice you have 2 holes pre-cut in the front curve of the underside of the roof.
- Page 13 www.insigniarange.com Last Modified: 07/10/2015 Accessory Installation Please Note Ensure all grey backing film on the rear of the glass panels are pierced through the existing glass holes with a knife to provide an efficient smooth fitting and location of the accessories. We recommend using a screwdriver on the smaller holes.
- Page 14 www.insigniarange.com Last Modified: 07/10/2015 Hand Shower Attach the chrome riser bar to the glass wall ensuring the water inlet is inserted through the lower large hole and hand tightened from the rear side. Now tighten the chrome shower holder ensuring that this will take the hand shower itself without falling (please note over tightening will prevent the holder from sliding up and down) Thermostatic Probe...
- Page 15 Connect the corresponding hoses to the rear of the valve as shown. Device output may differ from the image. Please refer to your outer chrome faceplate in- side your Insignia shower as a reference point. IF YOUR DIAL DOES NOT CORROSPOND TO THE APPROPRIATE DEVICE: Turn on your water to the shower and note which output the water exits from then turn off the water and swap over the relevant hose.
- Page 16 www.insigniarange.com Last Modified: 07/10/2015 Connecting the Front Column lights Locate the grey extension cable which has a white connection block on one end and a spit male/ female lead the other. Locate the wires from the front columns (left/right) and screw in the 4 wires matching each colour. E.g 2 x reds together and 2 x black together and tighten securely in to the connection block.
- Page 17 www.insigniarange.com Last Modified: 07/10/2015 Connecting the Tray lights Locate the black supplied extension lead and con- nect the end with the single connection to the light on the roof of the shower as shown in the image. Locate the 2 other connections on the at the oppo- site end and connect one end to the tray lights With the last remaining connector, connect this up to the lead supplied from the electric box represent-...
- Page 18 www.insigniarange.com Last Modified: 07/10/2015 Electric Box/Steam Generator Connections Light 2 Ozone Speaker Light Radio Aerial Audio In Connection RJ11 Phone Connection Thermostatic Probe...
- Page 19 www.insigniarange.com Last Modified: 07/10/2015 Steam Generator Connections The steam generator has 3 connections. Steam Outlet: Connect the white insulated hose to the white steam pod within your shower. Make sure these are fitted in the correct position as they are only attached for transportation reasons only.
- Page 20 www.insigniarange.com Last Modified: 07/10/2015 Silicone Seal where shown in red on the inside of the shower TESTING FOR WATER LEAKS LEAVING SHOWER 24 HOURS AFTER BUILD ALLOWING SEALENT TO CURE With all connections tight, the waste and hoses checked, jets fully sealed, your shower still around 18 inches from its designated final resting point and the silicone fully cured (hence leaving for 24 hours minimum) Switch on the overhead shower NOT the massage jets, remember these will fire water out at you and are not suitable for checking leaks as they would normally only operate when a person is in front of them.
- Page 21 www.insigniarange.com Last Modified: 07/10/2015 MK117 Control Panel Instructions Button 1 (Light Bulb) Button 7 (Down Arrow) Press 1x For Top Light and tray lights Channel select down/manual search Press 2x For internal column lights and Front Column Lights Button 8 (TUN) Press 3x For All Lights Switch Between manual &...
- Page 22 Last Modified: 07/10/2015 Need Help? If so then simply download Insignia’s free comprehensive help and troubleshooting brochure now! Simply visit: www.insigniarange.co.uk/help.aspx...
- Page 23 www.insigniarange.com Last Modified: 07/10/2015 Parts List Internal Items Framework SP037 Fan & Speaker cover Part Code Part Description Part Code Part Description SP134 Monsoon Shower head SP164 MK117 Control panel GT8002-12 Top Rail SP056 Ozone Module (for Steam SP190 Blister pack GT8002-13 Bottom rail Showers)
- Page 24 All images are registered with ImageTraker Insignia™ is a registered trademark of Maclean International Ltd All images are subject to copyright. Images may not be used in any way shape or form with out written permission from Maclean International Ltd. Images are NOT permitted...