Allnet ALL-SG8308PM User Manual

Smart managed 8 port poe+ gigabit switch

Hide thumbs

Table of Contents

Quick Links

Download this manual

ALL-SG8308PM

Smart Managed 8 Port PoE+

Gigabit Switch

User Manual

Irrtum und Änderungen vorbehalten

Table of Contents

Need help?

Do you have a question about the ALL-SG8308PM and is the answer not in the manual?

Questions and answers

Summary of Contents for Allnet ALL-SG8308PM

Page 3 L o g o u t … … … … … … … … … … … … … … … … … … … … … … … … … . … … … … 3 6 Safety Warning………………………………………………………………………38 CE Declaration of Conformity……………………………………………………39 ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 5: Product Overview
It is suitable for both metro-LAN and office application. Web Management Features  Configuration System Ports VLANs Aggregation LACP RSTP IGMP Snooping Mirroring Quality of Service Power over Ethernet Storm Control  Monitoring Statistics Overview ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 6: Specifications
 Number of Port 8-port 10/100/1000BaseT(X) with 8-port PoE+ Mechanical  LED Indicator Port 1~8: Link/ Act, 1000M. Port 1~8: PoE Per Unit: Power  Power Consumption: 130 Watts (Max), 30 Watts (Max) per port ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 7: Package Contents
Package Contents Before you start to install this switch, please verify your package that contains the following items:  One PoE Gigabit Ethernet Switch  One AC Power Cord  One User Manual ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 8: Hardware Description
Table 1-1 LED Indicators Status Description Power is on. Power Power is off. 10/100/1000 Link is connected Link/ACT Port 1~8 10/100/1000 Link is disconnected providing the power Port 1~8 not providing the power ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 9: Rear Panel
"The equipment is designed for building installation and not intended to be connected to exposed (outside plant) networks including campus environment and the ITE is to be connected only to PoE networks without routing to the outside plant." ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 10: Software Description
Just clicks the Apply then the login process is completed and comes out the sign “Password successfully entered”. Figure 1-1 After the user login, the left side of website shows all functions as Fig. 1-2. Figure 1-2 ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 11 ALL-SG8308PM - User Manual Configuration System System Configuration This page shows system configuration information. User can configure lots of information as Fig. 1-3: Figure 1-3 ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 13  Mode: allow user to manually set the port speed such as Auto, 10 half, 10 Full, 100 Half, 100 Full, 1000 Full or Disabled. User may press Apply button to complete the configuration procedure. Figure 1-4-1 ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 14  VLAN ID: ID of configured VLAN (1-4096, no leading zeroes).  VLAN Configuration List: Lists all the current VLAN groups created for this system. Up to 16 VLAN groups can be defined. VLAN 1 is the default untagged VLAN. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 15 VLAN identifier (PVID). Each row of the table corresponds to one port or trunk; trunked ports cannot be configured individually; configure the trunk instead. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 16 It is assigned to untagged frames received on the specified interface. The PVID has no effect on ports that have Packet Type set to “Tagged Only.” (Default PVID: 1) It is not possible to remove a port ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 17 To assign a port to a trunk, click the required trunk number, and then click Apply. Figure 1-6 LACP IEEE 802.3ad Link Aggregation Control Protocol (LACP) increases bandwidth by automatically aggregating several physical links together as ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 18 MAC address will then become the root device.  Hello Time: Interval (in seconds) at which the root device transmits a configuration message (BPDU frame). Number between 1-10 (default is ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 19 Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. Set the RSTP pathcost on the port. Number between 0 - 200000000. 0 means auto generated pathcost. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 21  IGMP Querying Enabled: When enabled, the port can serve as the Querier, which is responsible for asking hosts if they want to receive multicast traffic. Figure 1-9-1 ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 22  Ports to Mirror: Select the ports that you want to mirror from this section of the page. A port will be mirrored when the “Mirroring Enabled” check-box is checked. Figure 1-10-1 ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 23 1, 2, 4, 8 for queues 0 through 7, respectively. (This is the default selection.) Note: WRR can only be selected if Jumbo Frame mode is disabled on the Port Configuration page ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 24 802.1p values to a local priority queue (low, normal, medium or high). The default settings are shown below. When the QoS Mode is set to 802.1p, the 802.1p Configuration table is displayed as shown below. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 25 DSCP, the DSCP Configuration table is displayed, allowing you to map each of the DSCP values to a hardware output queue (low, normal, medium or high). The default settings map all DSCP values to the high priority egress queue. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 26 It is deployed in applications where AC power would be inconvenient, expensive or infeasible to supply. Web Smart features are able to remote control and centralized the power management. Via a current CAT 5 cable, ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 27 You can protect your network from broadcast storms by setting a threshold for broadcast traffic for each port. Any broadcast packets exceeding the specified ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 28 Figure 1-13-2 Monitoring Statistic Overview Statistic Overview for all ports User can mirror traffic from any source port to a target port for real-time analysis the following figures shows clearly the statistics overview. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 30 (provided in the last configuration message) becomes the designated port for the attached LAN. If it is a root port, a new root port is selected from among the device ports attached to the network. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 31  manual selection (see the RSTP Port Configuration table) or auto-detection. Note that if the switch detects another bridge connected to this port, the manual setting for Edge Port will be overridden, and the port will instead function as a point-to-point ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 32 User can perform cable diagnostics for all ports or selected ports to diagnose any cable faults (short, open etc..) and feedback a distance to the fault.  Cable Diagnostics: Cable diagnostics is performed on a per-port basis. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 33  Destination does not respond: If the host does not respond, a “timeout” appears in ten seconds.  Destination unreachable: The gateway for this destination indicates that the destination is unreachable.  Network or host unreachable: The gateway found no corresponding entry in the route table. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 35: Maintenance
Configuration file transfer allows you to save the switch’s current configuration or restore a previously saved configuration back to the device. Configuration files can be saved to any location on the web ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 36 Figure 3-5 Reset button for the factory default setting Please take the following steps to reset the Web Smart Switch back to the original default: Step 1: Turn on the Web Smart Switch ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 37 Press and hold the reset button continuously for ~20 seconds and release the reset button. Step 3: The switch will reboot for 20 seconds and the configuration of the switch will fall back to the default settings. ALLNET GmbH Computersysteme 2015 – All rights reserved...
Page 38: Safety Warnings
Do not expose your device to dust or corrosive liquids.  Do not use this product near water sources.  Make sure to connect the cables to the correct ports.  Do not obstruct the ventilation slots on the device. ALLNET GmbH Computersysteme 2015 – All rights reserved...

Allnet ALL-SG8308PM User Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Allnet ALL-SG8308PM

Summary of Contents for Allnet ALL-SG8308PM

Table of Contents