Table of Contents
Advertisement
4.4. Memory protection function "
The memory protection function protects the selected memory so as to prevent it from erroneous
replacement of its data with different data copied from another memory.
When this function is actuated for a selected memory, it inhibits transcribing copied data to the memory
but permits to read data from the memory.
At the time of shipment or when all the memories are initialized by memory initialization function (
LED indications are as follows:
"in"、"a"、"b"、"c="off"、"sup"="on"
Operating procedure
Key
LED indication
"chc "→"init"
→"c0py"
"c0py"→"comp"
→"pr0t"
SFT
△ △ △ △
"pr0t"→"in"
ENT
"in"→"a"→"b"
SFT
→"c"→"sup"
→"in"
△ △ △ △
"in"→"off"
(When the memory is
protected, the display
ENT
changes to"on"from
"in")
"off"→"on"
SFT
→"off"
△ △ △ △
"on"→"pr0t"
ENT
If the ESC key is pressed, the parameter writer returns to the status one before.
・
1
(*
) Protecting operation of "sup" is different from that provided for other memories and is shown below.
With the same inverter types (capacities):
Standard
sup
parameter
on
off
Note: When inverter types (capacities) are different, copying operation of parameters
(including special parameters) is prohibited.
When the parameter writer is turned on as it is connected with the inverter.
"chc" appears on the display first and then "init" appears to indicate that
the power supply is being initialized. Lastly, the display shows "copy".
−Selecting a desired function−
Select "prot " (memory protecting function) with the SFT key.
Each time the SFT key is pressed. indication on the display changes from
"copy" (copying function) to "comp" (comparing function),"prot" (memory
protecting function). "clr" (memory initializing function) and to.."copy" again
in this order.
−Entering the selected function−
After selecting "prot " with the SFT key, press the ENT key and "in"
(selecting inverter memory) appears on the display.
−Selecting a memory to protect its data−
Each time the SFT key is pressed, indication on the display changes from "in"
(selecting inverter memory) to "a" (selecting memory A), "b" (selecting memory
B), "c" (selecting memory C), "sup" (special parameter selection*
"in" again in this order. Select the memory to protect its data.
−Entering the memory to protect its data−
After selecting "in" (selecting inverter memory, by way of example) with the SFT
key, press the ENT key and the display shows the present memory protection
status. (When "on" appears on the display, the selected memory is protected.
When "off" appears on the display, the Selected memory is not protected.)
−Protecting the selected memory−
Each time the SFT key is pressed, indication on the display changes between "
on" (protecting the selected memory) and "off" (cancelling protection of the
selected memory) alternately.
−Executing protection of the selected memory−
After selecting ''on" (protecting the selected memory, by way of example) with
the SFT key, press the ENT key. The parameter writer starts protecting the
selected memory (canceling protection in case of "off") and indication of the
display returns to "port".
With different inverter types (capacities):
Special
parameter
○
×
○
○
"
"prot
"
prot
prot
prot" " " "
Key operation and description
Standard
sup
parameter
on
○
off
×
(Note)
-
11
-
E6580724
1
) and to
○ Protection disabled
Special
parameter
(write permitted)
× Write protected
×
(write prohibited)
×
),
clr
Advertisement
Table of Contents
