Stanley STCI1804 Manual page 10

ENGLISH
control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This
and the impacting noise that the tool makes is normal and
does not indicate a problem.
5. Quick Release Chuck (Figure G)
NOTE: The chuck accepts 1/4 inch (6.35 mm) hex
accessories only.
Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
To install an accessory, insert the accessory into the
quick release chuck (4) until an audible click is heard to
ensure the accessory is locked in place.
To remove an accessory, pull the chuck collar (3) away
from the front of the tool, remove the accessory and
release the collar.
NOTE: The quick release chuck is spring-loaded. The
accessory will be ejected when the chuck collar is pulled
forward.
LED WORK LIGHT
When impact driver is activated by pulling the trigger switch (1),
the integrated LED work light (9) will automatically illuminate
the work area. NOTE: The work light is for lighting the
immediate work surface and is not intended to be used as a
flashlight.
BIT TIP STORAGE
Two magnetic bit storage slots (5) are built into the area on the
top of the tool.
Battery Fuel Gauge - Figure H
The tool is equipped with a battery fuel gauge (8).This can be
used to display the current level of charge in the battery during
use and during charging. It does not indicate tool functionality
and is subject to variation based on product components,
temperature and end-user application.
Checking battery charge during use:
Press the battery fuel gauge button (H1).

The three LEDs (H2) will illuminate indicating the percent

of charge in the battery (Figure H).
If LED light does not lluminate, charge battery.

NOTE: This battery is designed to not operate when a charge
below 20% of its capacity is reached. After the battery
charge is depleated, the tool will not operate until after the
battery has been recharged.
BELT CLIP - FIGURE I
A belt clip (10) is provided which can be switched to either side
of the tool based on user preference for convenient access and
storage during use.
Caution: Ensure the forward/reverse control button (2) is
in the center lock position before attaching tool to belt.
8
MAINTENANCE
Your Stanley tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuoussatisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart
from regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger
before cleaning it.
Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust

from the interior.
PROTECTING THE ENVIRONMENTS
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
avail able for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
BATTERIES
Run the battery down completely, then remove it
from the tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
SERVICE INFORMATION
Stanley offers a full network of company-owned and
authorized service locations throughout Asia. All Stanley
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service.Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Stanley
location nearest to you.
NOTES
Stanley's policy is one of continuous improvement to our

products and, as such, we reserve the right tochange
product specifications without prior notice.
Standard equipment and accessories may vary by

country.
Product specifications may differ by country.
