Maintenance; Troubleshooting; Protecting The Environment - Black & Decker BHFEV36B2D Manual

Place the dust canister over a trash bin and press the
u
dust canister lid release button (6a) to empty the dust
canister as shown in figure J.
Grasp the agitator wheel housing (21) and pull up
u
to remove.
Remove the filter (22), from the agitator wheel housing
u
(21) as shown in figure L.
Shake off or lightly brush any loose dust from the filter.
u
Install the the filter (22), into the agitator wheel
u
housing (21).
Install the agitator wheel housing (21) onto the dust
u
canister, until it "clicks" firmly into position.
Cleaning the filters
Once the filter and pre-filter are removed from the dust
u
canister shake off or lightly brush any loose dust from
the pre-filter and filter.
Rinse out the dust canister (6) with warm soapy water.
u
Wash the filters with warm soapy water.
u
Ensure the filters are completely dry before refitting
u
(24hrs).
Follow instructions in the "Removing pre-filter and
u
Removing filter" sections for assembly instructions.
Note: Maximum dust collection will only be obtained with
clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full
and requires emptying or that there is a blockage somewhere.
Wash the filters regularly using warm, soapy water and
u
ensure that they are completely dry before using again.
The cleaner the filter is, the better the product will perform.
It is very important that the filters are completely dry
u
and correctly in position before use.
Removing and clearing the rotary brushes
(Fig. M)
Warning! To reduce the risk of injury from moving parts,
disconnect battery before cleaning or servicing.
To remove the rotary brush (23) from the floor head (8)
u
depress the release button (24) as shown in figure M.
Lift the rotary brush from its locked position.
u
The rotary brush (23) can now be removed.
u
Clean the rotary brush, and reinstall. Ensure it is secured
u
in its locked position before operating.
Storage
The unit can be safely stored using the wall storage bracket
(5a) available through your service department.
as shown in figure N.
(Original instructions)

Maintenance

Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
Remove the battery.
u
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Replacing the filters
The filters should be replaced every 6 to 9 months and when-
ever worn or damaged. Replacement filters are available from
your BLACK+DECKER dealer.
Remove the old filters as described above.
u
Fit the new filters as described above.
u
Trouble shooting
Problem Possible Cause
Battery pack not
charged.
Unit will not
start.
Blockage.
Beater bar stops
Obstruction.
working.
Charger not plugged in.
Battery pack will
not charge.
Surrounding air
temperature too hot or
too cold

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
ENGLISH
Possible solution
Check battery pack charging
requirements.
Check floorhead tube.
Check extension tube.
Check between extension
tube and bowl
The unit is equipped with
a beater bar overload protec-
tion feature. Remove and
clean the beater bar of all
debris and obstructions
Plug charger into a working
outlet. Refer to Important
Charging Notes for more
details.
Move charger and battery
pack to a
4 °C or below +40 °C.
9