Table of Contents
Advertisement
CPUs for FTG Mode. The same applies for the additional Major
Channel number range of 128 – 135 in Physical tuning and
128 – 999 in Virtual tuning mode. When the TV is in FTG Mode,
the appropriate values will be visible in the (read-only) Installer
Menu. For an IP Start Channel, item 004 will show value 253, the
IP address, and the port number. For an RF Start Channel, item
004 will show the channel's Major and Minor numbers.
Note: If the TV is being configured for Application Tuning Mode
operation with Pro:Centric Direct, the Start Channel is set in the
Pro:Centric Direct Admin Client, and Installer Menu item 004 is
automatically updated accordingly. When the TV is in Application
Tuning Mode, the appropriate values will be visible in the (read-only)
Installer Menu. For an IP Start Channel, item 004 will show value
253, the IP address, and the port number. For an RF Start Channel,
item 004 will show the channel's Major and Minor numbers.
005 - CHAN LOCK (Channel Lock)
Channel Lock is ideal if the system must always be on the same
channel. If set to 1, Channel Lock is enabled and it is not possible
to change channels. If set to 0 (default), Channel Lock is disabled.
Generally, this feature is used in connection with item 004 STRT
CHANNEL where the Start Channel may, for example, be set to
3 or 4. If the Start Channel is 3, then the TV will remain locked on
channel 3.
NOTE: For items 007, 008, and 009
For legacy reasons, the scale used is 0 – 63. The PTC software
will translate this to the 0 – 100 scale used by the TV.
To translate a TV volume level to the Installer Menu value, use
the following formula:
Installer Value = TV Value x 63
100
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the TV is turned ON. This feature is useful for
an in-house information channel, since the TV will always select
that volume level when it is turned ON. The range of values is 0
to 63, 255. If set to 255, the last volume level before the TV was
turned OFF will be the current volume level when the TV is turned
ON again.
Note: The factory default volume level (i.e., when AC power is
initially applied) for these TV models is 20. In addition, if AC power
is removed/disconnected and then reapplied to the TV while this
item is set to 255, the TV volume level will revert to 20 when the
TV is turned ON again.
206-4354
Installer Menu (Cont.)
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range
is from 0 to 63. The factory default is 0, which provides the full
range of volume control, if item 009 MAX VOLUME is set to 63. It
is recommended to set the same value on every TV.
Note: The minimum volume level cannot have a value setting
higher than the maximum volume level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb
others. The value range is 0 to 63, with 63 as the default, which
gives the user the full range of volume control, if item 008 MIN
VOLUME is set to 0. It is recommended to set the same value on
every TV.
Note: The maximum volume level cannot have a value setting
lower than the minimum volume level (described above).
010 - MUTE DISABLE
Enables or disables the sound Mute function. If set to 1, sound
cannot be muted. If set to 0, sound can be muted.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature is enabled and available to the
end user. Set to 0 to disable the Sleep Timer feature.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, the Timer function is enabled and available to the end
user. Set to 0 to disable On/Off timers.
Note: The TV clock must be set in order for timers to be used.
017 - ALARM
If set to 1, the Alarm feature is enabled and available to the end
user in the Function Menu (i.e., the TV is not in Pass-through
Mode). Set to 0 to disable the Alarm feature.
Note: The TV clock must be set before the Alarm feature will work.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on "bed
number" in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Values
IR Mode
0
Disabled
16 – 24
Multi-code Remote
Note: For further information, see documentation for the accessory
package that includes the multi-code remote.
Bed #
N/A
1 – 9
43
Advertisement
Table of Contents
