Related Manuals for Multitech MTCBA-G-EN-F4-NAM
Summary of Contents for Multitech MTCBA-G-EN-F4-NAM
- Page 1 ® MultiModem Wireless EDGE, GPRS, CDMA Modems with Ethernet Interface Quick Start Guide...
- Page 2 MultiModem, the Multi-Tech logo, and Multi-Tech. All products or technologies are the trademarks or registered trademarks of their respective holders. Technical Support Country By Email By Phone Europe, Middle East, Africa: support@multitech.co.uk +(44) 118 959 7774 U.S., Canada, all others: support@multitech.com 800 972-2439 or 763-717-5863 World Headquarters Multi-Tech Systems, Inc.
- Page 3 MultiModem Wireless Modem with Ethernet Interface Introduction The purpose of this guide is to cover safety concepts, the basic connections, and general setup of the Multi-Tech wireless MultiModem with Ethernet interface. For detailed information see the User Guide which is available on the MultiModem CD accompanying your wireless product and on the Multi-Tech Web site.
- Page 4 MultiModem Wireless Modem with Ethernet Interface “WARNING – Explosion Hazard – Substitution of Components may Impair Suitability for Class I, Division 2”. “WARNING – Explosion Hazard – Do not Disconnect Equipment Unless Power has been switched off or the area is known to be Non-hazardous”. “WARNING –...
-
Page 5: Ship Kit Contents
MultiModem Wireless Modem with Ethernet Interface Ship Kit Contents Unbundled Package Bundled Package Modem with Not Accessories Modem with Accessories 1 modem 1 modem 1 fused DC power cable 1 power supply cable 4 rubber feet for flat (varies) surface mounting 4 rubber feet for flat 1 Quick Start Guide surface mounting... - Page 6 MultiModem Wireless Modem with Ethernet Interface Connect the Antenna, Ethernet, and Power • Antenna. Connect a suitable antenna to SMA connector. An antenna is supplied with the bundled package ship kit. If you purchase a single unit, you must supply your own antenna. See the User Guide for antenna/RF specifications.
-
Page 7: Set Your Pc's Tcp/Ip Address For Ethernet Functionality
MultiModem Wireless Modem with Ethernet Interface Fused DC Power Connection • Connect the fused DC power cable to the DC power source on the vehicle or machine in which you are mounting the modem. Be sure the GND connection is correct. -
Page 8: Using At Commands
MultiModem Wireless Modem with Ethernet Interface ∗ Check Obtain IP Address Automatically and Obtain DNS Server Address Automatically. If you check these, then the DHCP function obtains the IP Address automatically from the Ethernet wireless modem, or ∗ Check Use the Following IP Address and Use the Following DNS Server Address. - Page 9 MultiModem Wireless Modem with Ethernet Interface Open the Command Window and Access Modem Mode You must be in modem mode in order to enter AT Commands. • From the workstation, open the command window by clicking the Start button and selecting Run. •...
- Page 10 MultiModem Wireless Modem with Ethernet Interface Type AT+WMBS=<Band>,<Param>. Press Enter. For <Band>, enter the option you desire: 4 = Dual-band mode 850/1900MHz 5 = Dual-band mode 900/1800MHz For <Param>, enter the option you desire: 0 = The modem will have to be reset to start on the specified band(s).
-
Page 11: Configure The Ethernet Interface Using The Web Management Software
MultiModem Wireless Modem with Ethernet Interface Configure the Ethernet Interface Using the Web Management Software You are now ready to configure the Ethernet interface. This is accomplished by using the modem's factory-installed Web Management software. The software is accessed through a Web Browser. - Page 12 MultiModem Wireless Modem with Ethernet Interface The Setup Wizard Screen The following is a screen shot of the Setup Wizard. Using this screen saves you time so that you are not entering the same information several screens; the data entered here defaults to the other screens.
- Page 13 MultiModem Wireless Modem with Ethernet Interface Idle Time Out – Sets the amount of time the PPP link stays active before disconnecting. Setting the value to zero causes the link to stay active continuously. Dial Number – Enter the dial number. This number connects you to the Internet.
-
Page 14: Setting Time And Date
MultiModem Wireless Modem with Ethernet Interface Setting Time and Date The date and time must be set using the Web Management software. The time and date set in IP Setup will not be correct unless the SNTP client is enabled and you have a live Internet connection. See SNTP Client in User Guide for more details. - Page 16 82010074L...