Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ERNITEC MicroView MVIC-04IR-E
Summary of Contents for ERNITEC MicroView MVIC-04IR-E
- Page 1 Camera Network Cube Camera Quick Start Guide MVIC-04IR-E...
- Page 2 Network Cube Camera·Quick Start Guide About this Manual This Manual is applicable to MVIC-04IR-E Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
- Page 3 Network Cube Camera·Quick Start Guide Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 4 Network Cube Camera·Quick Start Guide 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU, RE Directive 2014/53/EU.
- Page 5 Network Cube Camera·Quick Start Guide This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence.
- Page 6 Network Cube Camera·Quick Start Guide This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
- Page 7 Network Cube Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ●...
- Page 8 Network Cube Camera·Quick Start Guide malfunction), and affect the endurance of sensor at the same time. ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
- Page 9 Network Cube Camera·Quick Start Guide responsibility for problems caused by unauthorized repair or maintenance.)
-
Page 10: Table Of Contents
Network Cube Camera·Quick Start Guide Table of Contents 1 Appearance Description ............. 10 2 Notice ..................14 3 Installation ................. 16 Memory Card Installation ..........17 Stand Mounting ............18 Ceiling Mounting ............19 4 Setting the Network Camera over the LAN ......... 22 Wiring ................ -
Page 11: Appearance Description
Network Cube Camera·Quick Start Guide 1 Appearance Description There are two types of appearances for 24 series camera. Please refer to the figure below. And one appearance will be taken as an example in the chapter below. Type I Appearance Type II Appearance... - Page 12 Network Cube Camera·Quick Start Guide Overview...
- Page 13 Network Cube Camera·Quick Start Guide Description Description Lens Microphone IR LED Alarm: Solid red when the camera is armed; Solid blue when the camera is unarmed Status: Solid blue when the camera is Indicator added to the Guarding Vision Link: Flashing amber when network is connected;...
- Page 14 Network Cube Camera·Quick Start Guide Description O: Alarm Output Interface Power supply interface (12 VDC) Speaker Note: Press RESET about 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. ...
-
Page 15: Notice
Network Cube Camera·Quick Start Guide 2 Notice Do not install the Do not touch the lens camera in the extreme with your finger. whether condition. Do not install the Do not subject the camera to vibration, camera towards the strong light or in the shock or heavy pressure. - Page 16 Network Cube Camera·Quick Start Guide High humidity may Under no circumstances damage the camera should you submerge the camera in any type of hardware; put it in dry and well-ventilated liquid. place. Electromagnetic radiation may affect the video data transmission and the image quality.
-
Page 17: Installation
Network Cube Camera·Quick Start Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. -
Page 18: Memory Card Installation
Network Cube Camera·Quick Start Guide finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. ● Make sure that there is no reflective surface too close to the camera lens. -
Page 19: Stand Mounting
Network Cube Camera·Quick Start Guide Stand Mounting Steps: Take the bracket out from the package. Bracket Align the camera body to the bracket, and rotate the camera body to fix it with the bracket. -
Page 20: Ceiling Mounting
Network Cube Camera·Quick Start Guide Install the Camera Body Assemble the camera as the steps above, and put the camera on the flat surface. Ceiling Mounting Drill the screw holes according to the drill template. Drill Template Screw hole All:for Mounting Base Drill Template Disassemble the 3-axis bracket. - Page 21 Network Cube Camera·Quick Start Guide Knob Pole Base Fixed Tray Disassemble the Bracket Install the fixed tray to the ceiling with the supplied screws. Install the base to the fixed plate. Install the Fixed Plate and Mounting Base Install the camera to the bracket.
- Page 22 Network Cube Camera·Quick Start Guide Install the Camera Adjust surveillance angel 1). Loosen the knob to adjust the panning position and tilting position. 2). After adjusting the angle of the camera to the desired position, fasten the knob. Knob 360° 90°...
-
Page 23: Setting The Network Camera Over The Lan
Network Cube Camera·Quick Start Guide 4 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. -
Page 24: Activating The Camera
Network Cube Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. -
Page 25: Activation Via Sadp Software
Network Cube Camera·Quick Start Guide 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 26 Network Cube Camera·Quick Start Guide SADP Interface Note: The SADP software supports activating the camera in batch. Please refer to the User Manual of SADP software for details. 3. Create a password and input the password in the password field, and confirm the password.
-
Page 27: Modifying The Ip Address
Network Cube Camera·Quick Start Guide 4. Click OK to save the password. You can check whether the activation is completed on the popup window. If activation failed, please make sure that the password meets the requirement and try again. Modifying the IP Address Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your... - Page 28 Network Cube Camera·Quick Start Guide Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP. Please refer to the User Manual of SADP for details.
-
Page 29: Accessing Via Web Browser
Network Cube Camera·Quick Start Guide 5 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:... - Page 30 Network Cube Camera·Quick Start Guide 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug- Note: You may have to close the web browser to finish the installation of the plug-in.