Tables - ABB HT599244 Operation Manual

Operation Manual / 4 Product description / A150-M58/68

Tables

Tables
Table 1: Related documents .......................................... 5
Table 2: Weight of complete turbocharger unit...... 10
Table 3: Torque-controlled tightening of the pres-
sure screws .................................................................... 17
Table 4: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 24
Table 5: Lubricating oil temperature at the inlet... 25
Table 6: Maximum lubricating oil temperature at the
outlet .............................................................................. 25
Table 7: Tightening torque (86505).......................... 29
Table 8: Expected replacement intervals ................ 35
Table 9: Maintenance table ........................................ 38
Table 10: Parameters for wet cleaning of com-
pressor ............................................................................ 41
Table 11: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 44
Table 12: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 45
Table 13: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 46
Table 14: Value table for soaking .............................. 54
Table 15: Malfunctions when starting - Delayed
start-up ........................................................................... 57
Table 16: Malfunctions when starting - Vibrations 57
Table 17: Malfunctions when starting - Rubbing of
rotating parts................................................................. 57
Table 18: Malfunctions during operation - Lubricat-
ing oil pressure too low............................................... 58
Table 19: Malfunctions during operation - Speed re-
duces............................................................................... 58
Table 20: Malfunctions during operation - Speed in-
creases ........................................................................... 58
Table 21: Malfunctions during operation - Exhaust
gas temperature too high .......................................... 59
Table 22: Malfunctions during operation - Charge air
pressure too low........................................................... 59
Table 23: Malfunctions during operation - Charge air
pressure too high ......................................................... 60
Table 24: Malfunctions during operation - Engine
performance losses ..................................................... 60
© Copyright 2020 ABB. All rights reserved.
Table 25: Malfunction - Turbocharger pumping ..... 61
Table 26: Malfunction - Sporadic surge blows ........ 61
Table 27: Malfunctions when stopping - Runout
noises ............................................................................... 62
Table 28: Malfunctions when stopping - Runout
time too short ................................................................ 62
Table 29: Malfunction of the speed measurement
system - No signal or poor signal amplitude .......... 63
Table 30: Malfunction of the speed measurement
system - Measured speed too high ........................... 63
Table 31: Malfunction of the speed measurement
system - Measured speed too low............................. 63
Table 32: Swivel lifting eyes ......................................... 65
Table 33: Press-off screws ........................................... 66
Table 34: Dismantling screw ....................................... 66
Table 35: Weights of assemblies ................................. 71
Table 36: Tightening torques ...................................... 72
Table 37: Tightening torques for insulation............. 73
Table 38: Press-off screws - gas outlet flange ........ 78
Table 39: Tightening torque (90012-01).................... 82
Table 40: Permissible clearances A and B................. 87
Table 41: Nozzle ring compression PD ...................... 88
Table 42: Tightening torque (90012-01).................... 91
Table 43: Tightening torque (51007) ......................... 92
Table 44: Tightening torque (79041) ......................... 93
Table 45: Tightening torque (72011) ......................... 94
Table 46: Permissible clearances N and R................. 97
Table 47: Tightening torque (51009) ....................... 100
Table 48: Tightening torque (51009)....................... 101
Table 49: Tightening torque (72051)........................ 103
Table 50: Permissible clearances A and B................ 112
Table 51: Nozzle ring compression PD...................... 113
Table 52: Tightening torque (51007)......................... 116
Table 53: Tightening torque (51007) with spanner
holder .............................................................................. 116
Table 54: Tightening torque (79041) ........................ 117
HZTL4041_EN Revision D March 2020