Table of Contents
Related Manuals for Boser HS-2605
Summary of Contents for Boser HS-2605
- Page 1 HS-2605 EDEN Embedded Engine Board •CRT/Panel•CompactFlash•133MHz FSB• •ATA/33/66/100•Mini PCI•SO-DIMM• •LAN•Audio•RS-232/422/485• •4COM•PC/104•USB•TV-Out•DOC• •WDT•H/W Monitor•Single +5V• •Industrial Embedded Single Board computer•...
- Page 2 Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. reserves the right to change or improve the contents of BOSER Technology Co., Ltd.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 General Description ........1 1.1 Major Features ............... 2 1.2 Specifications ................ 3 1.3 Board Dimensions..............4 Chapter 2 Unpacking ..........5 2.1 Opening the Delivery Package..........5 2.2 Inspection................5 Chapter 3 Hardware Installation ......7 3.1 Before Installation ..............7 3.2 Board Layout ................. - Page 4 Chapter 4 AMI BIOS Setup ........31 4.1 Starting Setup..............31 4.2 Using Setup ................. 32 4.3 Main Menu................33 4.4 Standard CMOS Setup ............34 4.5 Advanced CMOS Setup ............35 4.6 Advanced Chipset Setup............ 36 4.7 Power Management Setup ..........37 4.8 PCI / Plug and Play Setup...........
- Page 5 Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the HS-2605 to ensure harmlessly discharge any static electricity through the strap.
-
Page 7: Chapter 1 General Description
I/O with CRT/Panel, LAN, Audio, TV-Out, and 4COM ports interfaces. Its onboard ATA/33/66/100 to IDE drive interface architecture allows the HS-2605 to support data transfers of 33, 66 or 100MB/sec. to one IDE drive connection. Designed with the VIA VT8606 core logic chipset, the board supports VIA C3 EDEN 400/667/733MHz Embedded CPU. -
Page 8: Major Features
To ensure the reliability in an unmanned or standalone system , the Watchdog Timer (WDT) onboard HS-2605 is designed with pure hardware that does not need the arithmetical functions of a real-time clock chip. If any program causes unexpected halts to the system, the onboard Watchdog Timer (WDT) will automatically reset the CPU or generate an interrupt to resolve such condition. -
Page 9: Specifications
Specifications CPU: VIA C3 EDEN 400/667/733MHz Embedded Low Power CPU Bus Interface: Mini PCI Local Bus Memory: One SO-DIMM socket supporting up to 256MB Chipset: VIA VT8606/VT82C686B I/O Chipset: SMC 37C669, VIA VT82C686B CompactFlash: One standard CompactFlash adapter VGA: VIA VT8606 integrated S3 3D supporting CRT/Panel displays up to 1920 x 1440 IDE: Two IDE disk drives supporting ATA/33/66/100 and with transfer rates of up to 33/66/100MB/sec. -
Page 10: Board Dimensions
Board Dimensions... -
Page 11: Unpacking
Chapter 2 Unpacking Opening the Delivery Package The HS-2605 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. - Page 12 It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately.
-
Page 13: Chapter 3 Hardware Installation
Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-2605. This chapter also contains information related to jumper settings of switch, watchdog timer, and the DiskOnChip address selection etc. Before Installation After confirming your package contents, you are now ready to install your hardware. -
Page 14: Board Layout
Board Layout... -
Page 15: Jumper List
Jumper List Jumper Default Setting Setting Page WDT Active Type Setting: Disabled All Open Clear CMOS: Normal Operation Short 1-2 JP4(1-4) DOC Address Select: D000 Short 1-2, 3-4 Short 5-6, 7-8, JP4(5-10) WDT Timer Select: 1sec. 9-10 RS-422/485 Receiver All Open Enabled/Disabled Select: Disabled COM2 Use RS-232 or RS-422/485 Open... -
Page 16: Configuring The Cpu
DOC in your system, please set both at different memory address mapping to avoid the mapping area conflicts. Failing to do so will not make the HS-2605 and the additional memory device function properly. JP4(1-4): DiskOnChip Address Select... - Page 17 3.7.1 Installing DiskOnChip Modules When installing a DiskOnChip module onto your board, please take note of the following: 1. Orient yourself properly with the location of the DiskOnChip socket. Try to locate the pin 1 location on your socket. Pin numbers are usually printed on either the component side or the solder side of your board.
-
Page 18: Vga Controller
VGA Controller The HS-2605 provides three connection methods of a VGA device. CN20 offers a single standard CRT connector while CN21 is the 50-pin panel connector and CN22 is the LVDS interface connector onboard reserved for flat panel installation. - Page 19 Please set the proper voltage of your panel using JP7 before proceeding on installing it. The HS-2605 has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP7 offers two voltage settings for the user.
-
Page 20: Pci E-Ide Drive Connector
PCI E-IDE Drive Connector CN23 is a standard 44-pin 2.0mm pitch connector daisy-chain driver connector serves the PCI E-IDE drive provisions onboard the HS-2605. A maximum of two ATA/33/66/100 IDE drives can be connected to the HS-2605 via CN23. CN23: IDE Connector... -
Page 21: Floppy Disk Drive Connector
3.10 Floppy Disk Drive Connector The HS-2605 uses a standard 34-pin header connector, CN8, for floppy disk drive connection. A total of two FDD drives may be connected to CN8 at any given time. CN8: FDC Connector Description Description DRVDEN0... -
Page 22: Serial Port Connectors
3.11 Serial Port Connectors The HS-2605 offers two NS16C550 compatible UARTs with Read/Receive 16-byte FIFO serial ports and four internal 10-pin headers and one RS-422/485 connector. CN16: COM1 Connector (5x2 Header) PIN Description PIN Description DCD1 DSR1 DCD1 DSR1 RXD1... - Page 23 CN19: COM4 Connector (5x2 Header) PIN Description PIN Description DCD4 DSR4 DCD4 DSR4 RXD4 RTS4 RXD4 RTS4 TXD4 CTS4 DTR4 TXD4 CTS4 DTR4 CN10: RS-422/485 Connector (5x2 Header, COM2) PIN Description PIN Description RTS- RTS+ CTS+ RTS- CTS- RTS+ CTS+ CTS- NOTE: The terminal resistance of RX &...
-
Page 24: Parallel Connector
3.12 Parallel Connector CN12 is a standard 26-pin flat cable connector deigned to accommodate parallel port connection on the HS-2605. CN12: Parallel Connector Description Description Strobe Auto Form Feed DATA 0 ERROR# DATA 1 Initialize DATA 2 Printer Select LN#... -
Page 25: Ethernet Connector
R/C GND R/C GND R/C GND R/C GND R/C GND R/C GND R/C GND 3.14 USB Connector The HS-2605 provides one 8-pin connectors, at location CN1, for two USB connections to the HS-2605. CN1: USB Connector Description Description USBD1- USBD0- USBD1+ USBD0+ 3.15 CMOS Data Clear... -
Page 26: Power And Fan Connectors
Before you turn on the power of your system, please IMPORTANT: set JP2 to Short 1-2 for normal operation. 3.16 Power and Fan Connectors HS-2605 provides one 5-pin power connectors at CN2. And one 2-pin power in at CN5. CN2: 5-pin ATX Power In Connector PIN Description PIN Description... -
Page 27: System Front Panel Connectors
Mouse Clock 3.18 System Front Panel Connectors The HS-2605 has one LED at location JP3 that indicates the power-on status. This visual feature of the IDE LED may also be connected to an external IDE LED, Speaker, Reset Switch, Power LED, EXT SMI, Power Button, and SLP Button via connector JP3(13-15), JP3(1-3-5-7), JP3(9-11), JP3(2-4), JP3(6-8), JP3(10-12), JP3(14-16). -
Page 28: Watchdog Timer
Connector JP3 Orientation PWR LED SPEAKER EXT_SMI PWR button RST_SW HD_LED SLP button CN25: External Reset Button PIN Description Reset 3.19 Watchdog Timer There are three access cycles of Watch-Dog Timer as Enable, Refresh and Disable. The Enable cycle proceeds via READ PORT 443H whereas the Disable cycle proceeds via READ PORT 045H. - Page 29 JP4(5-10): WDT Timeout Period Select Period PINS 5-6 PINS 7-8 PINS 9-10 Short Short Short 1 sec (default) 2 sec Open Short Short 10 sec Short Open Short 20 sec Open Open Short 110 sec Short Short Open 220 sec Open Short Open...
-
Page 30: Mini Pci Connector
AL,DX ; get back AX, DX 3.20 Mini PCI Connector HS-2605 supports a Mini PCI connector. The peripheral component with standard Type1 Mini PCI can be used. For particular requirement, please refer to “BOSER Mini PCI series product” on website or contact with us. - Page 31 Description Description SERR# STOP# 3.3V PERR# DEVSEL# C/BE[1]# AD[14] AD[15] AD[13] AD[12] AD[11] AD[10] AD[9] AD[8] C/BE[0]# AD[7] 3.3V 3.3V AD[6] AD[5] AD[4] REQ2 AD[2] AD[3] AD[0] GNT2 AD[1] GNT3 IRQ7 Mini PCI Socket pin orientation...
-
Page 32: Pc/104 Connectors
3.21 PC/104 Connectors The PC/104 expansion bus offers provisions to connect all types of PC/104 modules. With the PC/104 bus being known as the new generation of industrial embedded 16-bit PC standard bus, thousands of PC/104 modules from multiple venders can be easily installed onboard. - Page 33 CN4: PC/104 64-pin Connector Description PIN Description Connector diagram rotated 90 degrees -IOCHECK clockwise from RESETDRV original position IRQ9 -12V +12V IOCHRDY -SMEMW SA19 -SMEMR SA18 -IOW SA17 -IOR SA16 -DACK3 SA15 DRQ3 SA14 -DACK1 SA13 DRQ1 SA12 -REFRESH SA11 SYSCLK SA10 IRQ7...
-
Page 34: Audio Connectors
3.22 Audio Connectors The HS-2605 has an onboard AC97 3D audio interface. The following tables list the pin assignments of the Line In/Audio Out connector. CN9: Line In/Audio Out Connector PIN Description PIN Description AOUTL AOUTR AOUT_L AOUT_R MIC IN MIC IN 3.23 CompactFlash... -
Page 35: Game Port Connector
Description Description EWE0 VCC (+5V) Reset IORDY REQ 0 IDE LED PDIAG DATA 8 DATA 9 DATA 10 Inserting a CompactFlash card into the adapter is not a difficult task. The socket and card are both keyed and there is only one direction for the card to be completely inserted. -
Page 36: Tv-Out Connector
3.25 TV-Out Connector HS-2605 can support TV-Out function which input could be up to 800 x 600 graphics resolutions. World Wide Video standards are supported including NTSC-M (North America, Taiwan), NTSC-J (Japan), PAL-B, D, G, H, I (Europe, Asia), PAL-M (Brazil), PAL-N (Uruguay, Paraguay) and PAL-NC (Argentina). -
Page 37: Chapter 4 Ami Bios Setup
Chapter 4 AMI BIOS Setup The HS-2605 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. -
Page 38: Using Setup
Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> keys to change entries, and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. Move to previous item ↑... -
Page 39: Main Menu
Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>... -
Page 40: Standard Cmos Setup
Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the capacity of the IDE hard disk drive is larger than 528MB, you must set the HDD mode to LBA mode. -
Page 41: Advanced Cmos Setup
Advanced CMOS Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. AMIBIOS SETUP – ADVANCED CMOS SETUP (C)2001 American Megatrends, Inc. All Rights Reserved Quick Boot Enabled Available Options:... -
Page 42: Advanced Chipset Setup
Advanced Chipset Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. -
Page 43: Power Management Setup
Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. AMIBIOS SETUP – POWER MANAGEMENT SETUP (C)2001 American Megatrends, Inc. -
Page 44: Pci / Plug And Play Setup
PCI / Plug and Play Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. -
Page 45: Peripheral Setup
Peripheral Setup The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. -
Page 46: Hardware Monitor Setup
4.10 Hardware Monitor Setup AMIBIOS SETUP – HARDWARE MONITOR SETUP (C)2001 American Megatrends, Inc. All Rights Reserved *** System Hardware Monitor *** Available Options: TSENS1 Temperature Disabled CPU Fan Speed Enabled Vcore Reset + 2.500V + 3.300V + 5.000V ESC: Exit : Sel PgUp/PgDn: Modify F2/F3: Color... -
Page 47: Change Supervisor/User Password
4.12 Change Supervisor/User Password AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Enter new supervisor password: _ Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving... -
Page 48: Auto Configuration With Optimal Settings
PASSWORD DISABLED. When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. -
Page 49: Auto Configuration With Fail Safe Settings
4.14 Auto Configuration with Fail Safe Settings When you press <Enter> on this item you get a confirmation dialog box with a message similar to the figure below. This option allows you to load/restore the default values to your system configuration, optimizing and enabling all high performance features. -
Page 50: Save Settings And Exit
4.15 Save Settings and Exit Pressing <Enter> on this item asks for confirmation: AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Save current settings and exit (Y/N) ? Y Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings... -
Page 51: Exit Without Saving
4.16 Exit Without Saving Pressing <Enter> on this item asks for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect. This exits the Setup utility and restarts your computer. - Page 52 This page is intentionally left blank.
-
Page 53: Chapter 5 Software Utilities
Chapter 5 Software Utilities This chapter contains the detailed information of IDE, VGA and LAN driver installation procedures. IDE Driver Installation The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA and Audio drivers. - Page 54 Press “VIA 4 IN 1” and to go Setup. Once the Welcome screen appears on the screen, make sure to close any applications running and then click on the Next button.
- Page 55 When the Readme window pops on the screen, you may read the whole document including the license agreement or just press Yes to skip through and continue installation. The 4 in 1 Setup dialog is now displayed. Select on Normally Install and then click on Next.
- Page 56 The next window lists all components detected in your system and asks you to select the ones requiring drivers. Tick on all items then proceed by clicking on the Next button below the screen. The program starts to install the ATAPI driver when you click the Next button on the screen below.
- Page 57 The following screen then gives you the choice of installing the AGP driver in standard o turbo mode. Select on the Standard Mode and then click on Next to proceed. 10. Installation of the AGP driver is now complete. Once the screen below appears, select on restarting your computer to activate all drivers/settings completed.
-
Page 58: Vga Driver Installation
VGA Driver Installation 5.2.1 VGA Driver Installation for WIN95/98/2K With the Utility CD Disk still in your CD ROM drive, open the File Manager and then select the CD-ROM drive. As soon as the system reads the disk, the VGA Menu screen below will appear on your display. - Page 59 Select the operating system of your computer to proceed with the installation process.
- Page 60 Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next button. When the display below appears on your screen, Setup is already ready to install and copy the related files onto your hard drive.
-
Page 61: Vga Driver Installation For Win Nt4.0
After the installation finishes, you will be prompted to restart your system. We recommend you to reboot your computer to allow the new settings to take effect. Click on the Finish button to reboot. 5.2.2 VGA Driver Installation for WIN NT4.0 Click the Start button on the lower left hand corner of your screen, then select Setting. - Page 62 Specify the path of the new driver and then press on Enter. (If in driver D:, type d:\Vga/Via_8606/Nt40) Select S3 Graphics Twister Click OK or press Enter.
- Page 63 You will see warning panel about Third Party Drivers. Click on Yes to finish the installation. Once the installation is completed, you must shut down the system and restart for the new driver to take effect.
-
Page 64: Lan Driver Installation
LAN Driver Installation 5.3.1 LAN Driver Installation for WIN95/98/2K 1. With the Utility CD Disk still in your CD ROM drive, right click on My Computer icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu. - Page 65 2. Select on Other Devices from the list of devices then double-click on PCI Ethernet Controller.
- Page 66 3. The PCI Ethernet Controller Properties screen then appears, allowing you to re-install the driver. Select Driver from the main menu to proceed. 4. The window then displays the current status of your LAN driver. Press on Update Driver button to continue. 5.
- Page 67 6. When the succeeding window asks you what you wish Windows to do, tick on the “Search for a better driver….” Click on the Next button to proceed. 7. The Update Device Driver Wizard will then ask you to specify, by ticking, the path of the new driver.
- Page 68 8. Press on the OK button as soon as you have located the path of your driver. 9. Once the program returns to the Add New Hardware Wizard screen, your specified location will appear. Press on the Next button to continue. 10.
- Page 69 11. When copying of driver files finishes, the program will then ask you to insert your Windows. 12. The program then copies the necessary files from your Windows installation disk to complete the driver setup process. Once the driver is completely installed, the following message appears on your display.
-
Page 70: Lan Driver Installation For Win Nt4.0
5.3.2 LAN Driver Installation for WIN NT4.0 With the Utility CD Disk still in your CD ROM drive, right click on Network Neighborhood icon from the Windows menu. Select on Properties. The system automatically detects the absence of Windows NT Networking. - Page 71 Tick on the “Wired to Network” once the following screen appears. Click on the Next to proceed. Click on the Start Search button for the program to locate the Network Adapter.
- Page 72 Once setup finishes the search, it will list a number of adapters for you to choose from. Press on the Have Disk button to assign the driver path location. Setup now asks you for the location of the driver. When you have entered the new driver path, press on the OK button to continue.
- Page 73 When Setup finds the information it needs about the new driver, it will display the device it found on the following screen. Press on the OK button to accept and proceed. Setup then returns to Network Setup Wizard screen and displays your new Network Adapter.
- Page 74 The Network Setup Wizard then allows you to set the Network Protocols on your network. Select the appropriate protocol and then click on Next to continue. 10. Before Setup starts installing the components found and the settings you made, it will give you the option to proceed or go back for changes from the following screen.
- Page 75 11. Windows NT Setup will then need to copy files necessary to update the system information. Specify the path then press Continue. 12. Once it finishes copying the files, Setup will now allow you to choose the Duplex Mode of your LAN controller. Press on the Continue button after making your selection.
- Page 76 13. When Setup asks if you wish to change the TCP/IP settings of your system, select the appropriately. The default choice is No. 14. Setup then starts the Networking installation and copies the files.
- Page 77 15. When Setup finishes copying, the TCP/IP properties of your system will then pop up on your screen like the one shown below. Make the necessary changes then click on OK to continue. 16. When the screen below appears, click on Next to continue.
- Page 78 17. Setup then prompts you that it is ready to start the network. You may complete the installation thereafter. Click on Next to continue. 18. Assign the workgroup or domain setting of your computer. Click on Next to continue.
- Page 79 19. Restart your computer once the screen below appears. Click on Finish to continue. 20. Click on the Yes button to restart your computer. The LAN driver installation for WIN NT4.0 is now complete.
-
Page 80: Audio Driver Installation
Audio Driver Installation With the Utility CD Disk still in your CD ROM drive, open the File Manager and then select the CD-ROM drive. As soon as the system reads the disk, the VGA Menu screen below will appear on your display. Click on VIA_AC97 from the main menu. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next button. - Page 81 The Select Components dialog box is now displayed. Select on Install driver and then click on Next. The program will now require the Windows installation disk for proper hardware installation. Insert the CD and then click on Next.
- Page 82 When the display below appears on your screen, Setup is already installing and copying the related files onto your hard drive. Click on the Next button to proceed. After the audio driver installation finishes, select the Finish button to complete the installation process.