1. Manuals
  2. Brands
  3. Boser Manuals
  4. Computer Hardware
  5. HS-5210
  6. Manual

Boser HS-5210 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HS-5210/5020
Half Pentium
Half Size All-in-one with VGA Interface•100-Based Network
Supports DMA33•WDT•DOC•CTA•USB•IrDA
ISA Bus Industrial Single Board Computer
HS-5210V/5020V
Half Pentium
Half Size All-in-one with VGA Interface
Supports DMA33•WDT•DOC•CTA•USB•IrDA
ISA Bus Industrial Single Board Computer
HS-5210P/5020P
Half Pentium
Half Size All-in-one •Supports DMA33
WDT•DOC•CTA•USB•IrDA
ISA Bus Industrial Single Board Computer
®
TM
MMX
VGA LAN
®
TM
MMX
VGA I.S.B.
®
TM
MMX
I.S.B.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HS-5210 and is the answer not in the manual?

Questions and answers

Related Manuals for Boser HS-5210

Summary of Contents for Boser HS-5210

  • Page 1 HS-5210/5020 ® Half Pentium VGA LAN Half Size All-in-one with VGA Interface•100-Based Network Supports DMA33•WDT•DOC•CTA•USB•IrDA ISA Bus Industrial Single Board Computer HS-5210V/5020V ® Half Pentium VGA I.S.B. Half Size All-in-one with VGA Interface Supports DMA33•WDT•DOC•CTA•USB•IrDA ISA Bus Industrial Single Board Computer HS-5210P/5020P ®...
  • Page 2 Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. Intel is a registered trademark of Intel Corporation. Award is a registered trademark of Award Software, Inc.

  • Page 3: Table Of Contents

    Contents HS-5210/5020 ......................1 HS-5210V/5020V ....................1 HS-5210P/5020P ....................1 GENERAL INFORMATION..................3 1.1 M ....................4 AJOR EATURES 1.2 S ......................5 PECIFICATIONS 1.3 D ....................6 ELIVERY ACKAGE HARDWARE INSTALLATION................... 7 2.1 C ................7 AUTION OF TATIC LECTRICITY 2.2 C ........8...
  • Page 4 3.13 F ................27 THERNET ONNECTOR AWARD BIOS SETUP....................28 4.1 M ......................29 4.2 S CMOS S ..................30 TANDARD ETUP 4.3 BIOS F ..................31 EATURES ETUP 4.4 C ..................32 HIPSET EATURES ETUP 4.5 I ..................33 NTEGRATED ERIPHERALS 4.6 P ................34 OWER ANAGEMENT ETUP A BRIEF BROWSE OF 10/100 BASED-T LAN RTL-8139’S INSTALLATION SOFTWARE.................35...

  • Page 5: General Information

    Chapter-1 General Information The HS-5020 is a ISA bus (HS-5210 for PISA bus) MMX™ /Pentium® Industrial Single Board (I.S.B.) CPU card with features combine together to make it an ideal all-in-one industrial single board computer, enhanced I/O effects, VGA and NE2000 compatible Network interface.

  • Page 6: Major Features

    CPU 75∼300 MHz, AMD k5, k6,k6-2 333MHz, 350MHz Cyrix 6x86, M2 300MHz, Intel MMX™ , Socket 7 ZIF socket. SiS 5598 chipset. 100 base Network on board, NE2000 compatible. ( HS-5210/5020 only ). Ultra DMA33 Supported four fast PCI enhanced IDE drives (large hard disks, CD-ROM, tape backup, etc.)

  • Page 7: Specifications

    1.2 Specifications ?? CPU: Intel MMX/Pentium 75~300MHz, AMD k5, k6, k6-2 350 Cyrix 6x86,M2 300 ?? Bus interface: ISA bus / PISA bus ?? Chipset: SiS 5598 ?? Data bus: 64-bit ?? Processing ability: 64-bit ?? VGA Controller: SiS 5598 chipset built in GUI/Video accelerator and 24 bit true color RAMDAC, new generation UMA architecture with CPU Bus/Data compression and share system memory up to 4MB.

  • Page 8: Delivery Package

    ?? Operating temperature: 0~55°C (CPU need cooler) ?? Board size: 7.3"(L) x 4.8" (W) (185mm x 122mm) 1.3 Delivery Package The delivery package of HS-5210/5020 includes all following items: ? ? HS-5210/5020 Industrial Single Board ? ? One Printer & COM2 Bracketed Flat Cable...

  • Page 9: Hardware Installation

    Hardware Installation This chapter provides the information on how to install the hardware of HS-5210/5020. At first, please follow up sections 1.3, 2.1 and 2.2 in check the delivery package and carefully unpacking. Following after, the jumpers setting of switch, watchdog timer, and the DiskOnChip? address selection.

  • Page 10: Caution On Unpacking And Before Installation

    HS-5210/5020 from electricity discharge. With refer to section 1.3, please check the delivery package again with following steps: 1. Unpacking the HS-5210/5020, keep well storage of all packing material, manual and diskette etc. if has. 2. Is there any components lose or drop from the board? DO NOT INSTALL IF HAPPENED.

  • Page 11: Hs-5210/5020' S Layout

    2.3 HS-5210/5020’ s Layout...

  • Page 12: Quick Listing Of Jumpers

    CN11: USB0 CONNECTOR CN12: COM2 (HEADER 5x2) CN13: COM1 (HEADER 5x2) CN14: 8P POWER CONNECTOR CN15: RJ-45 NETWORK CONNECTOR ( HS-5210/5020 only ) CN16: COM1 ( HS-5210P/5020P only ) CN17: MINI-DIN 6-PINS MOUSE CONNECTOR (PS/2) CN18: EXTERNAL VGA CONNECTOR (DB15)

  • Page 13: Jumper Setting Description

    2.6 Jumper Setting Description A jumper pin-set is ON as a shorted circuit with a plastic cap inserted over two pins. A jumper pin-set is OFF as a open circuit with a plastic cap inserted over one or no pin(s) between pins. The below figure 2.2 shows the examples of different jumper pin-set setting as ON or OFF in this manual.

  • Page 14: Setting The Cpu Of Hs-5210/5020

    2.7 Setting the CPU of HS-5210/5020 The HS-5210/5020 provides all possibility in jumper setting for wide using all types of CPU with JP1 and JP3 setting. The following table shows all possibility of the setting with JP3. The JP3 used to setting the System clock base rate. The System clock setting will preset the system operating clocking base rate.
  • Page 15 Correspond to different type CPU, it is request to set JP6 for match the CPU's Vcore operating voltage. Here shows at below of the proper jumper settings for their respective Vcore at range 2.0V to 3.5V. CPU Vcore Voltage Selection CPU Vcore Voltage 2.0V ALL OFF...

  • Page 16: System Memory Dram

    See the figure on section 2.3 for get the identifying the banks. Please take notes that the memory capacity of both SIMMs should be the same. The HS-5210/5020 requires at least 2pcs of the RAM modules on SIMM socket. 2.9 Watch-Dog Timer There are three access cycles of Watch-Dog Timer as Enable, Refresh and Disable.
  • Page 17 JP4 : WDT Time - Out Period PERIOD *1 sec 2 sec 10 sec 20 sec 110 sec 220 sec The Watch-dog timer is disabled after the system Power-On. The watch-dog timer can be enabled by a Enable cycle with reading the control port (443H), a Refresh cycle with reading the control port (443H) and a Disable cycle by reading the Watch-dog timer disable control port (043H).

  • Page 19: Vga Controller

    WT_Refresh PUSH ; keep AX, DX PUSH DX,WDT_ET_RF ; refresh the watch-dog timer AL,DX ; get back AX, DX WT_DISABLE PUSH PUSH DX,WDT_DIS ; disable the watch-dog timer AL,DX ; get back AX, DX 2.10 VGA Controller The SiS 5598 Chip with built-in VGA controller is a highly integrated single chip solution for Pentium PCI/ISA system.

  • Page 20: Diskonchip? Address Setting

    D.O.C. module. 2.12 BIOS Type Selection The HS-5210/5020 provides a JP5 for selects the type of flash chip in using as the BIOS. The manufacturer provides 29C010 on the board. JP5 : BIOS Type Selection PIN NO.

  • Page 21: Connection

    Chapter-3 Connection This chapter gives all necessary information of the peripheral's connections, switches and indicators. 3.1 The Floppy Disk Drive Connector A standard 34-pin header daisy-chain driver connector provides as CN5 with following pin assignment. Total two FDD drivers may connect. CN5 : FDD CONNECTOR PIN NO.

  • Page 22: Pci E-Ide Drive Connector

    3.2 PCI E-IDE Drive Connector Two standard 40-pin header daisy-chain driver connectors provides as CN3 & CN4 with following pin assignment. Total four IDE (Integrated Device Electronics) drivers may connect. CN3(IDE 1) : Primary IDE Connector CN4(IDE 2) : Secondary IDE Connector CN3/CN4 : IDE Interface Connector PIN NO.

  • Page 23: Parallel Port Connector

    3.3 Parallel Port Connector A standard 26-pin flat cable driver connector provides as CN2 with following pin assignment for connection to parallel printer. CN2 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION STROBE DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5...

  • Page 24: Serial Ports Connectors

    3.4 Serial Ports Connectors The HS-5210/5020 offers two high speed NS16C550 compatible UARTs with Read/Receive 16 byte FIFO serial ports with one DB-9 external connector, and one internal 10-pin header connector. CN16 COM-1: Serial Port DB-9 Connector ( HS-5210P/5020P only ) PIN NO.

  • Page 25: Keyboard Connectors

    3.5 Keyboard Connectors The HS-5210/5020 offers two possibilities for keyboard connections to external PS/2 type keyboard at CN20, or an internal 5-pin header at CN1. CN1 : 5-pin Header Keyboard Connector PIN NO. DESCRIPTION KEYBOARD CLOCK KEYBOARD DATA GROUND CN20 : 6-pin Mini-DIN Keyboard Connector PIN NO.

  • Page 26: External Speaker

    CN8 : HDD LED connector PIN NO. DESCRIPTION HDD ACTIVE# 3.7 External Speaker The HS-5210/5020 has an on-board buzzer. And it also provides the CN6 in allows user to connecting to the external speaker. CN6 : Speaker Connector PIN NO. DESCRIPTION...

  • Page 27: Vga Connectors

    GREEN BLUE GROUND GROUND GROUND GROUND GROUND HSYNC VSYNC 3.10 IR Connector The HS-5210/5020 provides a 5-pin internal IR communication connector. The CN9 provides for IrDA 1.0 specification application. CN9 : 5-PIN IR CONNECTOR PIN NO. DESCRIPTION IRRX GROUND IRTX...

  • Page 28: Extra Power Connector

    3.11 Extra Power Connector The HS-5210/5020 provides an 8-pin extra DC power connector CN14 for internal power connection at a single board application. Please refer to the following table for detail pin information. CN14 : 8P Extra Power Connector PIN NO.

  • Page 29: Fast Ethernet Connector

    3.13 Fast Ethernet Connector The Fast Ethernet controller provides with 32-bit performance, PCI bus master capability, and full compliance with IEEE 802.3 10/100Based-T specifications. For 10/100Base-T operation, please connect the network connection by plugging one end of the cable into the 9-pin RJ-45 CN13 Connector. CN13 : Ethernet Connector ( 9-pin RJ-45 ) PIN NO.

  • Page 30: Award Bios Setup

    Chapter-4 AWARD BIOS Setup The board uses Award PCI/ISA BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options which could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features.

  • Page 31: Main Menu

    4.1 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>...

  • Page 32: Standard Cmos Setup

    4.2 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, please set the HDD mode to LBA mode.

  • Page 33: Bios Features Setup

    4.3 BIOS Features Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. ROM PCI/ISA BIOS (xxxxxxxx) BIOS FEATURES SETUP AWARD SOFTWARE, INC.

  • Page 34: Chipset Features Setup

    4.4 Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses.

  • Page 35: Integrated Peripherals

    4.5 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship which is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks.

  • Page 36: Power Management Setup

    4.6 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. ROM PCI/ISA BIOS (xxxxxxxx) INTEGRATED PERIPHERALS AWARD SOFTWARE, INC.

  • Page 37: A Brief Browse Of 10/100 Based-T Lan Rtl-8139'Sinstallation Software

    Chapter-5 A Brief Browse of 10/100 based-T LAN RTL-8139’ s Installation Software This chapter only provides for HS-5210/5020. The content herein is not for HS-5210P/5020P. The on board provides one 32-bit PCI 10/100 based-T Ethernet LAN interface connection for easy using this Industrial Single Board in connection to-with Novell NE2000 compatible LAN network system.

This manual is also suitable for:

Hs-5020Hs-5210vHs-5020vHs-5210pHs-5020p

Table of Contents