Table of Contents
Advertisement
This appliance may only be installed by a registeres LP Gas
installer.
All registered installers are issued with a card carrying their
registration number. Ask to be shown the card before allowing
the installation work to be shown the card before allowing the
installation work to commence and make a note of the installer
QCC number.
Upon completion of the installation, the installer is required to
explain the operational details of the appliance together with
the safety instructions.
You should only sign for acceptance of the installation and be
provided with a copletion certificate. You should only sign for
acceptance of the installation when the installation is completed
to your satisfaction.
Note that your invoice is required in the event that you wish
make a quarantee claim.
Important information for the installer
This appliance may only be installed by a registered LP Gas
installer registered with the Liquefied Petroleum Gas
Association of Southern Africa.
The appliance must be installed in accordance with the
requirements of SANS 10087-1 and any fire department
regulations and/or local bylaws applicable to the area. If in
doubt check with the relevant authority before undertaking the
installation.
Upon completion of the installation you are required to fully
explain and demonstrate to the user the operational details and
safety practices applicable to the appliance and the installation.
Moving the appliance by the gas line or door handle
Do not move the appliance while holding the gas line; the gas
pipe could be damaged. There is a risk of a gas leak! Do not
move the appliance while holding it by the door handle. The
door hinges and door handle could be damaged.
Electrical connection
Caution!
Have the appliance set up by your after-sales service. A 16 A
■
fuse is required for connection. The appliance is designed for
operation at 220-240 V.
If the electricity supply drops below 180 V, the electrical
■
ignition system does not work.
Any damage arising from the appliance being connected
■
incorrectly will invalidate the guarantee.
If the supply cord is damaged, it must be replaced by the
■
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
For the after-sales service
Caution!
The appliance must be connected in accordance with the
■
data on the rating plate.
Only connect the appliance to an electrical connection that
■
meets the applicable provisions. The socket must be easily
accessible so that you can disconnect the appliance from the
electricity supply if necessary.
Please ensure the availability of a multi-pin disconnecting
■
system.
Never use extension cables or multiple plugs.
■
For safety reasons, this appliance must only be connected to
■
an earthed connection. If the safety earth terminal does not
comply with regulations, safety against electrical hazards is
not guaranteed.
You must use a H 05 W-F type cable or equivalent for the
■
appliance connection.
8
Levelling the cooker
Always place the cooker directly on the floor.
Pull out the plinth drawer and lift it up and out.
1.
There are adjustable feet at the front and rear on the inside of
the plinth.
Use an Allen key to raise or lower the adjustable feet as
2.
necessary until the cooker is level (picture A).
Push the plinth drawer back in (picture B).
3.
$
Setting up the appliance
0LQ
The appliance must be set up directly on the kitchen floor
■
and in line with the specified dimensions. The appliance must
not be set up on any other object.
The distance between the top edge of the oven and the
■
bottom edge of the extractor hood must meet the
requirements of the extractor hood manufacturer.
Ensure that the appliance is not moved again after set up.
■
The distance from the high output burner or wok burner to
the fronts of the adjacent units or the wall must be at least 50
mm.
Measures to be noted during transport
Secure all mobile parts in and on the appliance using an
adhesive tape that can be removed without leaving any traces.
Push all accessories (e.g. baking tray) into the corresponding
slots with cardboard at the edges, in order to avoid damaging
the appliance. Place cardboard or similar between the front and
rear side to prevent knocks against the inside of the glass door.
Secure the door and, if available, the top cover to the appliance
sides using adhesive tape.
Keep the original appliance packaging. Only transport the
appliance in the original packaging. Observe the transport
arrows on the packaging.
If the original packaging is no longer available
pack the appliance in protective packaging to guarantee
sufficient protection against any transport damage.
Transport the appliance in an upright position. Do not hold the
appliance by the door handle or the connections on the rear, as
these could be damaged. Do not place any heavy objects on
the appliance.
%
Advertisement
Table of Contents
