Harvia Xenio CX004WIFI Instructions For Installation And Use Manual page 16

EN
* Factory setting
Figure 3b. Settings menu structure, additional settings.
16
Temperature unit
Change the setting with the
CEL (Celsius)
FAHr (Fahrenheit)
Press the MENU button to access the next setting.
Heater grade
Change the setting with the
See the right grade from the heater's type label, under "control
unit grade settings".
TYPE LABEL
WARNING! AVERTISSEMENT!
DO NOT PLACE ANY OBJECTS ON HEATER. COVERING CAUSES FIRE RISK.
NE PAS PLACER DES OBJETS AU-DESSUS DU POÊLE. IL Y A UN RISQUE D'INCENDIE SI LE POÊLE EST RECOUVERT.
AN INADEQUATELY FILLED ROCK SPACE CAUSES FIRE RISK.
IL Y A UN RISQUE D'INCENDIE SI LE RÉCIPIENT À PIERRES N'EST PAS CORRECTEMENT REMPLI.
For AC only / Look for the important additional instructions MODEL *Q POWER VOLTAGE
in the manual! / Consultez les instructions
Pour courant alternatif seulement (AC) MODÈLE PUISSANCE TENSION
supplémentaires importantes dans le manuel!
FOR SUPPLY CONNECTIONS USE COPPER
WIRE ONLY SUITABLE FOR AT LEAST 90 ºC inch mm
POUR LES CONNEXIONS ELECTRIQUES PREVOIR
A 2 50
UN CABLAGE RESISTANT AU MOINS A 90° C HL(S)7U1(Q) 6,8 kW
B 42 1060 B
Control units / Centres de contrôle:
HL(S)9U1(Q) 9,0 kW
CX30-U1-U3 / CX45-U1-U3 / CX-170-U1 /
A HL(S)11U1(Q) 10,5 kW
A A
CX-170-U1-15 / CX-170-U3 / CX-170-U3-15
A HL(S)7U3(Q) 6,8 kW
A
ETL LISTED
9,0 kW
CONFORMS TO HL(S)9U3(Q)
UL STD 875 A
CERTIFIED TO HL(S)11U3(Q) 10,5 kW
CAN/CSA STD HARVIA OY, FINLAND
3159549 E60335-2-53-05 *Q = includes built-in contactor / contient le contacteur integré
Press the MENU button to access the next setting.
WIFI connection
Connect control panel to WiFi network by using the MyHarvia application.
Change the setting with the
for more detailed instructions.
OFF >The WiFi connection is off
(WiFi indicator light on the control panel is off ).
On > The WiFi connections is on
(WiFi indicator light glows on the control panel).
COnn > Connect mode is active.
Press the MENU button. The control unit switches to standby mode.
and buttons.
and buttons.
CONTROL UNIT GRADE
All heater grades:
A1, A2, A3, A4, A5
B1 (default), B2, B3, B4, B5
PHASE SUPPLY FLOOR AREA CONTROL UNIT
WIRES SURFACE DE GRADE SETTINGS
TENSION PLANCHER PARAMÈTRES
DE CONTRÔLE
DE
MIN. MAX.
SERVICE DE QUALITÉ DE
SQ.FT SQ.FT L'UNITÉ C1, C2, C3, C4, C5
240 1 10 28 57 C2
240 1 8 45 79 C2
240 1 6 22 98 C1
208 3 12 28 57 C2
208 3 10 45 79 C2
D1, D2, D3, D4, D5
208 3 8 22 98 C1
E1, E2, E3, E4, E5, E6
and buttons. See MyHarvia application
SETTINGS
C2
(FOR EXAMPLE)