Advertisement
Quick Links
RFDA-73M/RGB
Dimming actuator for LED (RGB) strips, 3-channel
EN
Trokanalni dimer za LED (RGB) trake
RS
Characteristics /
Karakteristike
• The dimmer for LED strips is used for independent control of 3 single-color LED strips or one
RGB LED strip.
• The expanded selection of control modes enables it to be combined with:
a) Detectors, Controllers and System units iNELS RF Control
b) by control signal 0(1)-10V
c) by connecting to iNELS BUS using a DAC ballast.
• The unit's three-module design with switchboard mounting enables connection of dimmed
load 3x 5A, which represents:
a) single-color LED strip 7.2 W (ELKO Lighting) - 3x 8 m
b) RGB LED strip 14.4 W (ELKO Lighting) - 10 m.
• 6 light functions - smooth increase or decrease with time setting 2s-30 min.
• When switched off, the set level is stored in the memory, and when switched back on, it returns
to the most recently set value.
• The dimmer may be controlled by up to 32 channels (1 channel represents 1 button on the
controller).
• The power supply of the unit is in the range of 12-24 V DC, and is indicated by a green LED.
• The package includes an internal antenna AN-I, in case of locating the unit in a metal switch-
board, you can use the external antenna AN-E for better signal reception.
• Memory status can be pre-set in the event of a power failure.
• For components labelled as iNELS RF Control
via the RFAF/USB service device.
• Range up to 160 m (in open space), if the signal is insufficient between the controller and unit,
use the signal repeater RFRP-20 or protocol component RFIO
• Communication frequency with bidirectional protocol iNELS RF Control
• You will find more on light sources and dimming options at www.elkoep.com/solutions.
Assembly /
Montaža
mounting into switchboard
montaža u razvodnu tablu
Connection of an LED strip /
RF RGB
RF COLOR
-
+
-
+
-
+
-
+ +
RED
GREEN
BLUE
MASTER 10V
RFDA-73M/RGB
RED
GREEN
BLUE
GND
-
+
-
+
-
+ Un
R
G
B
RGB strip
/ traka
Radio frequency signal penetration through various construction materials /
For more information, see "Installation manual iNELS RF Control":
http://www.elkoep.com/catalogs-and-brochures
Made in Czech Republic
(RFIO
), it is possible to set the repeater function
2
2
that support this feature.
2
(RFIO
2
Konekcija sa LED trakom
RF WHITE
-
+
-
+
-
RED
GREEN
BLUE
RFDA-73M/RGB
GND
-
+
-
W
W
Single/ Pojedinačni LED
U-Energister, d.o.o.| Noveških interniraca 1V | 31000 Užice | Serbia | e-mail: office@elkoep.rs
U-Energister, d.o.o. | Norveških interniraca 1V | 31000 Užice | Republika Srbija | e-mail: office@elkoep.rs
Support: +381 63 479 880 |
EN
• Dimer za LED trake, koji se koristi za nezavisnu konrolu tri jednobojne LED trake ili jedne
RGB LED trake.
• Proširen izbor kontrolnih moda omogućava kombinaciju sa:
a) Detektorima, kontrolerima i sistemskim jedinicama iNELS RF Control
b) uređaj sa izlaznim signalom 0(1)-10V
• Dizajn sa tri modula sa montiranjem na radnu tablu omogućava povezivanje prigušnog opte-
rećenja 3x5A, što predstavlja:
a) jednobojna LED traka 7.2 W (ELKO Lighting) - 3x 8 m
b) RGB LED traka 14.4 W (ELKO Lighting) - 10 m.
• 6 funkcija osvetljenja - blago povećanje ili smanjenje sa vremenskim podešavanjem od 2s-
30 min.
• Kada se isključi, podešeni nivo se čuva u memoriji i vraća se na poslednje podešeno stanje
nakon ponovnog uključivanja.
• Univerzalnim dimerom se može upravljati do 32 kanala (1 kanal predstavlja 1 dugme na
kontroleru).
• Napon napajanja jedinice je u opsegu od 12 do 24 V DC i označen je zelenom LED lampicom.
• Paker uključuje unutrašnju AN-I antenu , u slučaju da se element postavi u metalnu razvod-
nu tablu, preporučuje se korišćenje spoljašnje AN-E antene za poboljšanje signala.
• Mogućnost podešavanja statusa memorije u slučaju nestanka struje.
• Za komponente označene kao iNELS RF Control
titora putem RFAF/USB. servisnog uređaja
• Domet do 160 m (na otvorenom prostrou ), uslučaju nedovoljnog signala između kontrolera i
jedinice, koristiti RFRP-20 repetitor signala ili elemente sa RFIO
).
2
funkciju.
• Frekvencija komunikacije sa dvosmernim protokolom iNELS RF Control
• Više informacija o izvorima svetlosti i opcijama zatamnjenja možete pronaći na www.elko-
ep.rs/resenja.
+
-
+ +
MASTER 10V
+
-
+ Un
W
Prenos radio frekvencijskih signala preko različitih građevinskih materijala
60 - 90 %
80 - 95 %
wooden structures
brick walls
with plaster boards
drvena konstruk-
zid od cigle
cija sa gipsanim
pločama
Za više informacija pogledati ,,Uputstvo za instalaciju iNELS RF Control":
https://www.elkoep.rs/preuzimanja
Tehnička podrška +381 63 479 880
RS
www.elkoep.rs
RGB
LED
trake
(RFIO
) moguće je podesiti funkciju repe-
2
2
protokolom koji podržava ovu
2
20 - 60 %
0 - 10 %
reinforced
metal partitions
concrete
metalne pre-
armirani beton
grade
02-37/2015 Rev.2
(RFIO
).
2
2
80- 90 %
common glass
staklo
1/10
Advertisement
Related Manuals for iNels RFDA-73M/RGB
Summary of Contents for iNels RFDA-73M/RGB
- Page 1 0(1)-10V • Dizajn sa tri modula sa montiranjem na radnu tablu omogućava povezivanje prigušnog opte- c) by connecting to iNELS BUS using a DAC ballast. rećenja 3x5A, što predstavlja: • The unit‘s three-module design with switchboard mounting enables connection of dimmed a) jednobojna LED traka 7.2 W (ELKO Lighting) - 3x 8 m...
- Page 2 The device can be combined with all system components, controls and devices Uređaj se može kombinovati sa svim sistemskim komponentama, kontrola- of iNELS RF Control and iNELS RF Control ma i uređajima iNELS RF Control i iNELS RF Control The detector can be assigned an iNELS RF Control (RFIO ) communication pro- Detektoru se može dodeliti iNELS RF Control...
- Page 3 Underlined RF address no. 1 listed on the front panel is used to con- Podvučena RF adresa br.1 navedena na prednjoj ploči koristi se za trol the actuator RFDA-73M/RGB with RF control units in the RF RGB upravljanje akuatorima RFDA-73M/RGB sa RF upravljačkim jedini- mode.
- Page 4 This mode enables use of 3 output channels for connecting 3 independent circuits of single- Ovaj režim omogućava upotrebu 3 izlazna kanala za povezivanje za 3 nezavisna kola ili jed- color LED strips. RFDA-73M/RGB can be controlled as 3 independent actuators RFDA-71B. nobojnu LED traku. RFDA-73M/RGB se može kontrolisati sa 3 nezavisna aktuatora RFDA-71B.
- Page 5 Two presses of your selected Press of programming button ton on actuator RFDA-73M/ button on the RF transmitter as- on actuator RFDA-73M/RGB RGB for 1 second will activate signs the function light scene 2 shorter then 1 second will fin-...
- Page 6 Four presses of your selected Press of programming button ton on actuator RFDA-73M/ button on the RF transmitter as- on actuator RFDA-73M/RGB RGB for 1 second will activate signs the function light scene 4 shorter then 1 second will fin-...
- Page 7 5 seconds, will RGB for 1 second will activate presses of the selected but- activate actuator into timing actuator RFDA-73M/RGB into ton on the RF transmitter mode. LED flashs 2x in each programming mode. LED is (must be a lapse of 1 s be- 1s interval.
- Page 8 The mode is used to control the actuator by analog inputs 0 - 10 V by using the DAC3- Režim se koristi za upravljanje elementom pomoću analognih ulaza 0 – 10V uz 04M or DAC3-04B. It is therefore possible to combine and control LED strips via iNELS. pomoć DAC3-04M ili DAC3-04B. Stoga je moguće kombinovati i kontrolisati LED trake putem iNELS-a.
- Page 9 Deletion does not affect the pre-set memory function. Pritiskom na taster PROG na elemetru RFDA-71M/RGB u Pritiskom na taster PROG koji se nalazi na RFDA-73M/RGB trajanju od 8s, briše se celokupna memorija elementa. LED u trajanju od 5s aktivira se brisanje jednog kontrolera. LED trepće 4x u intervalu od 1s.
-
Page 10: Technical Parameters
* Maks. moment pritezanja konektora antene je 0.56 Nm. Attention: Upozorenje: When you instal iNELS RF Control system, you have to keep minimal distance 1 cm between each Kada instalirate iNELS RF Control sistem, mora se poštovati minimalno rastojanje od 1cm između units.