Download
Share
Print this page
  1. Manuals
  2. Brands
  3. EPV Manuals
  4. Projector Accessories
  5. EDGE FREE Sonic AT8 ISF eFinity Series
  6. User manual

EPV EDGE FREE Sonic AT8 ISF eFinity Series User Manual

Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
Acoustically Transparent EDGE FREE® Fixed Frame Screen
Product Description:
The Sonic AT8 ISF eFinity Series is a fixed frame projection screen that uses EPV's EDGE FREE®
technology. The EDGE FREE® design resembles a flat panel TV display. The eFinity includes a micro-
thin bezel trim to further enhance the frame appearance and absorb projector overshoot.
The screen material included is our ISF certified Sonic AT8 ISF, which is a high-resolution acoustically
transparent front projection material for speaker placement behind the screen.
In order for the Sonic AT8 ISF to maintain its projection qualities and optimum performance, please refer
to the list below for proper maintenance and cleaning.
• Use a soft bristle brush to spot clean for dust.
• Dip a soft bristle toothbrush in mild soap and water to clean light stains.
• Never rub or apply pressure when cleaning the surface.
• Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
• To avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other
•
sharp or abrasive objects.
02172022JA
Sonic AT8 ISF eFinity Series
USER'S GUIDE
www.epvscreens.com
U-00249
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the EDGE FREE Sonic AT8 ISF eFinity Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for EPV EDGE FREE Sonic AT8 ISF eFinity Series

Summary of Contents for EPV EDGE FREE Sonic AT8 ISF eFinity Series

  • Page 1 USER’S GUIDE Product Description: The Sonic AT8 ISF eFinity Series is a fixed frame projection screen that uses EPV’s EDGE FREE® technology. The EDGE FREE® design resembles a flat panel TV display. The eFinity includes a micro- thin bezel trim to further enhance the frame appearance and absorb projector overshoot.
  • Page 2 1. Frame and Edge Trim Parts List 2 pcs 2 pcs Main Frame Parts Edge Trim Parts item item vertical frame Part A. Part D. ½ horizontal frame Part B. Part E. ½ horizontal frame Part C. Part F. 2. Hardware Parts List M4*4 D5*4 M4*4...

  • Page 3: Frame Assembly

    ” ” Item Parts List Center Joints- M4 (bottom position) Center Joints-D5 (top position) Elbow Joints M4 (bottom position) Elbow Joints D5 (top position) Top wall brackets M4x7 Screws Spring Spring Hook Bottom wall brackets Φ5x50 Wall Screws Hollow Wall anchors M4x4 Screws Angle cover Center Support Bar...

  • Page 4: Back Side

    Step 5: Secure the elbow joints by fastening them with M4x7 screws ( , 4 at each corner. Screen Material Step 6: Put on the white gloves (p) and carefully unroll the screen material on a clean surface from the roller to the other side as shown below.
  • Page 5 Center Support Bar Step 9: Insert the Center Support Bar (o) into the upper top groove on the back of the frame with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove.
  • Page 6 Continue attaching the rest of the springs to the material in the following order in steps 5-12. To avoid ripples forming in the material it is imperative that all of the corners are properly wrapped around the edges as illustrated in the check mark diagrams. Note (after all springs have been attached): Correct material installation –Corners of the screen material are properly wrapped around the corner edges of the frame and material is evenly tensioned and flat, creating a nicely taut surface.

  • Page 7: Wall Installation

    Connect edge trim frames (e/f) together using the and secure with four of the Center Joints- M4(a) M4x4 Screws (m) as shown in Step 1. Repeat for other side. Once both top and bottom edge trim frames have been connected, attach the vertical (left/right) sides edge trim frames (d) using the and secure with four M4x4 screws (m) on all corners, Step 2.
  • Page 8 Don’t tighten the screw to allow the screen to move up and down Model/Size A = Top Wall A1 = Bracket hole B = Bottom Wall B1 = Bracket C = Top/Bottom bracket distance distance bracket distance hole distance Wall Bracket Height 590mm (23.23”) 750mm (29.53”) 1340mm (52.76”)