Advertisement
FX
-16CCL-M CC-Link SYSTEM MASTER BLOCK
2N
HARDWARE MANUAL
This manual contains text, diagrams and explanations which will guide the reader in the correct installation
and operation of the FX
-16CCL-M CC-Link SYSTEM MASTER BLOCK. It should be read and
2N
understood before attempting to install or use the unit. Further information can be found in the FX series
PLC hardware manuals.
Note's on the symbology used in this manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the user's personal safety and protect the integrity of the equipment.
Whenever any of the following symbols are encountered, its associated note must be read and
understood. Each of the symbols used will now be listed with a brief description of its meaning.
Hardware warnings
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property damage.
1. INTRODUCTION
1.1 Associated Manuals
Manual name
Manual number
★FX
-16CCL-M
JY992D93101
Describes programming and handling of the CC-
2N
User's Manual
(sent separately)
Link master block FX
★FX
/FX
/FX
/FX
JY992D88101
Explains the instructions available to the FX
1S
1N
2N
2NC
Programming Manual II
(sent separately)
FX
/FX
1N
2N
★FX
/FX
/FX
JY997D16601
Explains the instructions available to the FX
3G
3U
3UC
Programming Manual
(sent separately)
FX
/FX
3U
3UC
JY992D89301
Describes hardware specifications, wiring and
✩FX
Hardware Manual
1N
(packed with product)
mounting of the FX
Describes the contents related to the hardware
JY992D66301
✩FX
Hardware Manual
such as specifications, wiring and mounting of the
2N
(packed with product)
FX
Series PLC.
2N
JY992D33401
Describes the name of each part and harding of
✩FX
Hardware Manual
3G
(packed with product)
the FX
Series PLC.
3G
✩FX
Series User's
3G
Describes the contents related to the hardware
JY997D31301
Manual
such as specifications, wiring and mounting of the
(sent separately)
FX
Series PLC.
- Hardware Edition
3G
JY997D18801
Describes the name of each part and harding of
✩FX
Hardware Manual
3U
(packed with product)
the FX
Series PLC.
3U
✩FX
Series User's
3U
JY997D16501
Describes the hardware specifications, wiring and
Manual
(sent separately)
mounting of the FX
- Hardware Edition
✩FX
(DSS/S) Hardware
2NC
JY992D76401
Describes the hardware specifications, wiring and
Manual
(packed with product)
mounting of the FX
Describes the contents related to the hardware
✩FX
(D/UL)
JY997D87201
2NC
such as specifications, wiring and mounting of the
(packed with product)
Hardware Manual
FX
Series PLC.
2NC
✩FX
(D,DSS)
3U
JY992D28601
Describes the name of each part and harding of
Hardware Manual
(packed with product)
the FX
Series PLC.
3U
✩FX
Series User's
3UC
JY997D28701
Describes the hardware specifications, wiring and
Manual
(sent separately)
mounting of the FX
- Hardware Edition
✩FX
-32CCL
2N
JY992D71801
Describes programming and handling of the CC-
User's Manual
(packed with product)
Link interface block FX
★: Indispensable manual
✩: Manual required depending on equipment used
1.2 Overview
The CC-Link master block FX
as the master station of the CC-Link system.
CC-Link Ver.1.10
1) Remote I/O stations and remote device stations can be connected to the master station (FX Series
PLC).
Master station
Remote I/O station
Remote device station
2) By using the CC-Link interface block FX
JY992D93201D
remote device stations to configure a simple distributed system.
Partner manufacturer's
product
Description
1.3 Dimensions and Setting
-16CCL-M.
2N
Dimensions: mm (inches)
/
1S
85(3.34)
/FX
Series PLC.
2NC
75(2.95)
2-f4.5
/
3G
Series PLC.
10)
Series PLC.
1N
FX
-16CCL-M
2N
Number
Name
Series PLC.
3U
1)
LED
indicators 1
Series PLC.
2NC
Series PLC.
3UC
-32CCL.
2N
2)
Power indictor POWER
-16CCL-M is a special extension block which assigns an FX Series PLC
2N
: Station which controls the data link system
: Remote station which handles only bit information
: Remote station which handles both bit information and word information
-32CCL, two or more FX Series PLCs can be connected as
2N
CC-Link master block
FX
-16CCL-M
2N
FX
/FX
/FX
/FX
/FX
/FX
1N
2N
2NC
3 G
3 U
3 UC
Series PLC
Remote I/O station
Remote device station
Remote device station
CC-Link interface block
FX
/FX
/FX
/FX
/FX
/FX
/
0N
1N
2N
2NC
3 G
3U
FX
Series PLC
FX
-32CCL
2N
3U C
MASS (Weight): 0.4 kg (0.88 lbs)
87(3.43)
RUN
ERR.
MST
9)
TEST1
TEST2
L RUN
L ERR.
POWER
8)
12)
SW
E
M/S
R
PRM
R
TIME
O
LINE
R
SD
RD
9(0.35)
Inside of top cover
Description
LED
Description
name
ON : Module is normal.
RUN
OFF: Watchdog time error has occurred.
RUN
Indicates the communication status with the
ERR.
stations set in the parameters.
MST
ON
: Communication error has
TEST 1
ERR.
TEST 2
occurred in all stations.
Flashing : Communication error has
L RUN
occurred in some stations.
L ERR
MST
ON : Set as the master station
TEST1
Test result indication
TEST2
Test result indication
ON : Data link is being executed
L RUN
(host station).
ON
: Communication error has
occurred (host station).
L ERR.
Flashing : The settings of the switches 4) to
7) were changed while the power
was ON.
ON : 24V DC is supplied from the outside.
Number
Name
3)
LED
SW
indicators 2
M/S
E
R
PRM ON : Parameter setting error has occurred.
SW
E
R
M/S
R
R
PRM
O
TIME
TIME
O
R
LINE
R
SD
LINE
RD
SD
RD
Remote I/O station
4)
Station
Sets the station number of the module. (Default setting at shipment: 00)
number setting
switch
<Setting range>
00 (because the FX
STATION NO.
If "65" or larger number is set, the "SW" and "L ERR." LED indicators turn ON.
× 10
× 1
5)
Mode setting
Sets the operation status of the module. (Default setting at shipment: 0)
switch
Number
0
1
MODE
2
3
4
5
6
7
8 to A
B to F
6)
Transmission
Sets the transmission speed of the module. (Default setting at shipment: 0)
speed setting
Number
switch
0
B RATE
1
0
156K
RUN
2
FX
2N
-16CCL-M
ERR.
1)
1
625K
MST
TEST1
2
2.5M
TEST2
3
STATION
L RUN
3
5M
NO.
L ERR.
4)
´10
4
10M
2)
4
POWER
´
1
5 to 9
4
5)
MODE
11)
7)
Condition
Sets the operation condition. (Default setting at shipment: All OFF)
B RATE
6)
0
156K
1
625K
2
2.5M
setting switch
3
5M
7)
4
10M
ON
SW
OFF
ON
1
-
-
Number
2
-
-
SW
E
3
-
-
M/S
R
4
CLR
HLD
3)
PRM
R
5
-
-
6
-
-
TIME
O
7
-
-
LINE
R
SW
OFF
ON
ON
8
-
-
⎯
⎯
SD
1
SW1 to
RD
⎯
⎯
2
⎯
⎯
3
SW3
4
CLR
HLD
⎯
⎯
5
⎯
⎯
6
SW4
⎯
⎯
7
⎯
⎯
8
SW5 to
SW8
8)
Terminal block Connects dedicated CC-Link cables to enable data link. For the connection
method, refer to Section 2.3.
LED status
The terminals SLD and FG are connected inside.
Normal
Error
M3.5 Screw
ON
OFF
ON or
OFF
flashing
9)
Terminal block Connects the power supply to operate the master block.
M3 Screw
ON
OFF
OFF except during
test
10)
Extension
Connects the PLC.
cable
ON
OFF
11)
Next step
extension
Connects extension equipment.
connector
ON or
OFF
flashing
12)
DIN rail
mounting
DIN46277: DIN rail mounting groove of 35 mm (1.38") in width
groove
ON
OFF
*1 The [RD] LED is darker as the transmission speed is faster and as the number of connected stations
is smaller.
Description
ON : Switch setting error has occurred.
OFF
ON
ON : The master station is already present
OFF
ON
in the same line.
OFF
ON
ON : Data link watchdog timer errors has
OFF
ON
occurred (error in all stations).
ON : The cable is broken or the
transmission route has been affected
OFF
ON
by noise, etc.
ON : Data is being transmitted.
ON
OFF
*1
ON
OFF
ON : Data is being received.
-16CCL-M is dedicated to the master station)
2N
Name
Description
Online
Sets connection to data link.
⎯
(Unusable)
Offline
Sets disconnection from data link.
Line test 1
Refer to USER'S MANUAL.
Line test 2
Refer to USER'S MANUAL.
Parameter
Refer to USER'S MANUAL.
verification test
Hardware test
Refer to USER'S MANUAL.
(Unusable)
Setting error (The SW LED indicator turns ON.)
(Unusable)
Cannot be set because it is already used inside.
(Unusable)
Setting error (The SW LED indicator turns ON.)
Setting contents
156 kbps
625 kbps
2.5 Mbps
5 Mbps
10 Mbps
Setting error (The SW and L ERR. LED indicators turn ON.)
Switch status
Setting description
ON
OFF
(Unusable)
Always OFF
Keep
Clear
Input data status in data link faulty station
(HLD)
(CLR)
(Unusable)
Always OFF
Advertisement
