Regency Fireplace Products Greenfire GF900C-NG2 Owners & Installation Manual page 2

The control box will only learn the Remote ID codes during the first 30 seconds after power is applied
and will ignore this special command from the Remote after the first 30 seconds.
To the New Owner:
To match the control box to the remote, follow the steps below :
Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by REGENCY
1. Remove a battery from the remote handset.
the warmth and charm of a wood fireplace at the flick of a switch. The model GF900C has been approved by AGA for both
safety and efficiency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many
2. Remove main power to the control box by turning off the isolation switch or switch on the GPO to
trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of
your Regency Fireplace.
®
3. Wait 30 seconds (approx.).
4. Reconnect main power to the control box.
5. Immediately put the battery back in the remote & point the remote in the general direction of the
The control box will only learn the remote ID codes during the first 30 seconds after power
is applied and will ignore this special command from the remote afterward.
6. Press and hold the F F A A N N 1 1 & & F F A A N N 2 2 buttons simultaneously. The
To match the control box to the remote, follow the steps below:
1. Remove a battery from the remote handset.
7. Release both buttons.
2. Remove main power to the control box by turning off the isolation switch or switch on the
8. The display will revert back to the normal off mode display. The
GPO to the heater.
3. Wait 30 seconds (approx.)
9. Press the Off button on the remote. The heater should turn off.
4. Reconnect main power to the control box.
10. Wait approx. 30 seconds turn the on again & check all the functions
5. Immediately put the battery back in the remote & point the remote in the direction of the heater.
6. Press and hold the PROG and FAN buttons simultaneously. The letters "LC" will appear on
the display indicating ID code transmission.
Note: To view a step-by-step pairing video please visit
regency-fire.com.au/Customer-Care/Fireplace-Care-Videos
7. Release both buttons.
Note: The Remote Control Handset has a set of unique ID codes that is
8. The display will revert to the normal off mode display. The heater should light - spark, burner,
pre-programmed into its memory. This set of ID codes helps to
etc. - even though the remote screen says the heater is off.
differen-tiate one Remote Control Handset from another so that only
the control box with a matching ID code will respond to the appropriate
9. Press the OFF button on the remote. The heater should turn off.
Remote Control Handset.
10. Wait approx. 30 seconds to turn the heater on again & check that all functions work - fan
regency.com.au
speed and flame height can be adjusted, etc.
Note: To view a step-by-step pairing video please visit
regency-fire.com.au/Customer-Care/Fireplace-Care-Videos
Note: The remote control handset has a set of unique ID codes that is pre-progarmmed into its
memory. This set of ID codes helps to differentiate one remote control handset from another;
only the control box with a matching ID code will respond to a handset.
Note: The fan cannot be turned off during operation of this appliance.
2
PAIRING YOUR REMOTE CONTROL
the heater.
PAIRING YOUR REMOTE CONTROL
heater.
letters "LC" will appear on the display indicating the ID codes have
been transmitted.
heater should light – spark, burner, etc even though the remote
screen says the heater is off.
work – fan speed can be adjusted, flame height can be adjusted, etc.
. The GF900C has been designed to provide you with all
®
Regency GF900C-2 Gas Fireplace