1. Package Include Hard Tube Microphone Headphone&Mic Kits Wired Microphone Velcro Usb Cable Metal Clip EVA Booster 3M Glue Velcro HELMET BLUETOOTH INTERCOM User Manual FOCUS ON OUTDOOR SPORTS 2.5mm to 3.5mm Cable User Manual User Guide...
2. Charging: Power cable insert hole(socket) 2.1 The function button lights up red when charging, and the red light goes out after finishing (As shown below). Please charge before using for the first time. 2.2 Please use a qualified charger 5V/1A±0.5A. 2.3 Please keep charging at least once every 2 months if the product is not used for a long time.
3.Installation & Disassembly 3.1 Speaker Installation 1.Open the inner helmet lining on 2.Attach the Headphone with 3..Place Velcro on the right the ear position and attach the Velcro hook to the loop (the short position on the left side of the velcro loops.
Page 7
3.2 Fixed by clamp 1.Find and assemble the Unit base and metal clip. 2.Fix the base on the right position. 3.Assemble the M1 S-PLUS: Insert the snap of the 4.Insert the microphone plug , installation complete. bottom of the host in to the groove of the base, press the host to the base so that the clip of the base buckle the top of the host.
Page 8
3.3 Disassembly of the Device Slide up Pull out 1.Press the upper clamp buckle and move the 2. Pull out the microphone plug. device upward to remove it.
Switch On: Long press Intercom button and Function button at the same time for 3 seconds,Voice message will also say “ Welcome to FODSPORTS Bluetooth Communication System”. Switch Off: Long press Intercom button and Function button at the same time for 3 seconds.Voice...
Page 10
Low Power Notification: When power lower than 10%, red light flash in the function button and voice message will remind power lower than 10%,please recharge immediately. Power Detect Function: FX8 has power detect function,when device is on,short press Previous and Next button at the same time,recorded voice message will tell you:...
Page 11
Previous button twice Automatically switch on voice command input function When your FX8 is paired up with cellphone,short press Previous button twice,will automatically switch on the voice command function (only for iOS and Android ). *Cellphone must equipped with this function.* Music Function Play: When Standby,short press Function button once.
Page 12
Volume Down: When talking,Rotate the Function button backward. Memory Clear Memory Clear: When device is on,press Function and Previous button at the same time for 5 seconds.Then FX8 will clear the pairing memory with other devices. Reset Hold down for 5 seconds...
5.Device Pairing 5.1 Pairing Modes 5.1.1 Passive pairing mode Hold down for 3 seconds When device is on,long press Function button to enter Pairing Mode,red and blue lights flash quickly,voice notice “ pairing ”. Pairing mode for connection to Bluetooth devices such as mobile phones and Bluetooth GPS.
Page 14
5.2 (A) FX8 connect with (B) FX8 Intercom A FX8 is on positive search mode(refer to 5.1.2), B FX8 is on passive search mode (refer to 5.1.1),A and B FX8 change from flashing red and blue lights alternately to function and intercom buttons flashing blue lights at the same time,connect successfully.
Page 15
STEP2.Turn on cellphone Bluetooth,Select“ FODSPORTS FX8”,the pairing is complete.Voice message will notice “Device Connected”. 5.4 Connect with two phones Step1 . Connect to the first phone(refer to 5.3) Step2 . Long press the Function button, FX8 on passive search mode, connect to the second phone (refer to 5.3)
Page 16
Any device with 3.5mm connector can transmit voice signal to FX8. When device wire connected by 2.5mm to 3.5mm cable to FX8,Complete the wired sound source input. Press the [Previous] and [Next] buttons for 3 seconds to turn on or turn off the wired audio input.
6.1 Occasions: Rider A connect with Passenger B for intercom. Then A connect with two bluetooth devices and one wired equipment and B connect with one bluetooth device(as shown below). Step 1. A FX8 connect with B FX8(refer to 5.2) . Step 2. Short press one time A or B intercom button to disconnet intercom .
Page 18
Notice: If A or B need to use the audio function of phone(bluetooth device), you need to disconnect the intercom. 6.2 Multiple Intercom 6.2.1FX8 equipped with multiple intercom function,recommended 4 units(A,B,C,D), pairing procedure as follow: Active pairing mode Passive pairing mode (flash slowly) (flash quickly) Active pairing mode...
Page 19
Active pairing mode Passive pairing mode (flash slowly) (flash quickly) Step 1: Unit A is on positive search mode(refer to 5.1.2), Unit B is on passive search mode(refer to 5.1.1), Unit A and Unit B change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same time,connect successfully.Short press the intercom button of Unit B for one time, exit intercom state temporarily.
Page 20
*You can connect more FX8 by repeating the above methods. Notice: The first and the last one FX8 can connect with another 2 Bluetooth devices.The FX8 in the middle connection position of the group can connect with an additional Bluetooth device.
STEP2. Switch on all 4 units(A,B,C,D) in the same time(long press intercom and function buttons about 3 seconds). STEP3. Short press one intercom button of the 4 FX8 and they flash blue and red lights in the same time. Memory connection start successfully.
Long period or too loud may hurt hearing ability. Disassemble or Modification The FX8 is precisely made in factory.Any disassemble or modification may damage the device,please do not tear any of the safety regulation and serial sticker from the device ,that will void the warranty.Please contact us...
9.Statement / Warranty/After-Sale Service 9.1 FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.
Page 24
9.2 After-Sale Service For any quality problem or missing accessories, especially pairing problem between 2 or more FX8 headsets, please feel free to contact us at email: winzon.cs@outlook.com. We're always here ready to help, will reply to you in 24 hours.