Related Manuals for FODSPORTS FX4 PRO
Summary of Contents for FODSPORTS FX4 PRO
- Page 1 ___., a , .._ FODSPORTS Focus on outdoor spans FX4PRO HELMET BLUETOOTH INTERCOM User Manual Bluetooth· FOCUS ON OUTDOOR SPORTS...
-
Page 4: Package Contents
1.Package Contents 1x FX4 PRO Speaker & Hard Tube Microphone 1x Soft Microphone USB Cable Clip Mounting Bracket Spring Clip 3M Tape Bracket Velcro User Manual... - Page 5 2.Charging: "-,,, Power cable insert hole (socket) 2.1 The function button lights up red when charging, and the red light goes out after finishing charging(As shown below). Please fully charge before using for the first time. 2.2 Please use a qualified charger 5V/1A±0.5A. 2.3 Please keep charging at least once every 2 months if the product is not used for a long time.
-
Page 6: Installation Instructions
3. Installation Instructions 3.1.1 Insert the Clip Mounting Bracket between the internal padding and external shell of the helmet. � � == = 3.1.2 If there are any problems with mounting the bracket, you may use the 3M tape bracket.Peel off the protective backing sheet of the 3M tape and adhere the bracket onto the helmet.Press for 15 seconds and glue dry for 24 hours. - Page 7 � Note: Even though the 3M Tape mounting is provided for convenience, FODSPORTS recommends using the bracket mounting, T he 3M Tape mounting is offered as an option that you may use at your own risk and responsibility, FODSPORTS does not assume any responsibility for use of ii.
- Page 8 If you are installing into an open face helmet, please adjust the direction of the microphone so that the triangular mark on the microphone is pointing towards your mouth. 3.3 Place the speakers into the cheek pads. Push the speakers and microphone firmly against the Velcro pads.
- Page 9 Note: T he speaker with shorter wire is for the left ear and the speaker with the longer one is for the right ear, to enhance the FM radio reception as well. 3.5 Mount the FX4 PRO main unit on the bracket.Slide the main unit down onto the bracket until it clicks firmly into the bottom portion of the bracket.
-
Page 10: Switch On/Off
4.General Operation Instructions 1.Volume- 2.Volume+ 3.Function 4.lntercom 5.Charge slot 6.Headset Switch On/Off Switch On: Press and hold the Function button for about 3 seconds to switch on.The light will flash blue only. Switch Off: Press and hold the Function button for about 3 seconds to switch off. The blue light will turn red then off. -
Page 11: Low Battery Alert
Power Detect & Notification Function FX4 PRO has power detect Function,when device is on, short press Function button twice.recorded voice message will tell you: Battery Full Battery medium Battery Low Low Battery Alert When the main battery unit falls below 20% charge the light... -
Page 12: Voice Command
:While in standby, press and hold the "Volume - " button for Switch manual/automatic answering calls 7 seconds. (Default: answer incoming calls automatically) In some cases (e.g. high -power RF radio influence or metal blocking), the headset might Note: disconnect from the mobile phone. Please short press the Function button to reconnect. Voice Command When in standby mode, double click the "Volume-"... -
Page 13: Intercom Function
5. Pairing the FX4 PRO with a Bluetooth Device Before using the FX4 PRO Bluetooth headset with any Bluetooth device for the first time you need to pair them. It can be paired with mobile phones, audio devices such as MP3 or GPS, and other FODSPORTS... - Page 14 Step 2. Search for Bluetooth devices on your mobile phone. The headset will be listed on your mobile phone as "FODSPORTS FX4 PRO". Step 3. Enter 0000 for the PIN if needed. Step 4. Your mobile phone will confirm that pairing is complete. The blue light flash after they are connected.
- Page 15 Pairing with other FX4 PRO headsets for Intercom Talk : The FX4 PRO can be paired with other FX4 PRO up to four units for full duplex Bluetooth intercom talk. There is a different pairing process for each scenario: two intercoms, three intercoms, and four intercoms.
- Page 16 6.1 Pairing two FX4 PRO headsets to talk >)) unit A unitB 2 Persons Full Duplex Intercom Chatting Tips: To start an intercom talk. you should pair the two units firstly. Step 1: Pairing two FX4 PRO units firstly. Turn on unit A and unit B, then simultaneously hold the Intercom and "Volume+" buttons on both units for 2 seconds to enter pairing mode for channel 1, until the red and blue light flash on both units .
- Page 17 Then click the Intercom button on either unit, the blue light will flashes quickly on this unit. Once the will pairing is complete you see the blue light flashing on both units . unit A or unit B unit A and unit B Step 2: Start an intercom talk Click the Intercom button on one unit to start an intercom talk.
- Page 18 Click the Intercom button on one unit to quit the intercom. After disconnected you will see blue light flashing on both units. unit A or unit B unit A and unit B 6.2 Pairing three FX4 PRO headsets to talk >l) >)) (C< >))
- Page 19 Step 1: Pairing unit A with unit B firstly. Turn on unit A and unit B. then simultaneously hold the Intercom and "Volume + •• button on both units for 2 seconds to enter pairing mode for channel 1, until the red and blue light flash on both units. unit A unltB Then click the Intercom button on either unit, the blue light will flash quickly on this unit.
- Page 20 Step 2: Then pairing unit B with unit C Turn on unit C. Simultaneously hold the Intercom and "Volume-" button on both unit B and unit C for 2 seconds until the red and blue lights flash to enter pairing mode for channel 2. unit B unit C Then press the Intercom button on either unit until the blue light flashes quickly on this unit.
- Page 22 Note: When in group intercom talk, you can see blue light flashes simultaneously on each unit. When in the three persons intercom mode, all the intercom button flashes blue light. Step 4: Disconnect the intercom talk Use the Intercom button to disconnect the intercom talk. 4.1 Click the Intercom button on unit A or unit B to disconnect the two units, while unit Band unit C stay connected.
- Page 23 B and unit C Important Note: The Bridge unit cannot be connected with a Bluetooth device (phone or GPS) while ii is being used as an Intercom Bridge unit. 6.3 Pairing four FX4 PRO headsets to talk ((< >)) >)) ((<...
- Page 24 button on both units for 2 seconds until the red and blue lights flash to enter pairing mode for Channel 2. unit B unite Then press the Intercom button on either unit, the blue light will flash quickly on this unit. Once the pairing is completed you will see the blue lights flash on both units.
- Page 25 Step 2: Pairing the bridge units with end units Turn on unit A, simultaneously hold the Intercom and "Volume+" button on both unit A and unit B for 2 seconds until the red and blue lights of the both units flash to enter pairing mode for Channel 1. unit A unltB Then press the Intercom button on either unit.
- Page 26 Turn on unit D. Simultaneously hold the Intercom and "Volume+" button on both unit C and unit D for 2 seconds, until the red and blue lights flashes on both units to enter pairing mode for Channel 1. unite unitD Then Click the Intercom button on either unit, the blue light will flash quickly on this unit.
- Page 27 Step 3: Start 4 way intercom talk After all four units are paired, unit B and unit C have been set as bridge units. 3.1 Double click the Intercom button on unit B or unit C to connect the two bridge units. �...
- Page 28 unit C or unit D unit C and unit D Note: When in group intercom talk, you can see blue light flash simultaneously on each unit. When in the four persons intercom mode, all the intercom button flashes blue light. Step 4: Disconnect the intercom talk 4.1 Double click the Intercom button on unit B or unit C to disconnect the two bridge units.
- Page 29 4.2 Click the Intercom button on unit A or unit B to disconnect the two units. unit A or unit B unit A and unit B 4.3 Click the Intercom button on unit Dor unit C to disconnect the two units. unit C and unit D unit C and unit D To connect Bridge units, double-click the Intercom button.
- Page 30 • If one Intercom rider goes out of range during a conversation, there may be static and eventually the intercom will disconnect. In this case, the FX4 PRO automatically tries to reconnect the Intercom rider every eight seconds and you will hear high tone double beeps until the connection is reestablished. If you don't want to make a re-connection, press the Intercom button to stop the attempt.
- Page 32 Intercom call, and Intercom conversation is interrupted by an incoming mobile phone call. a.Maintenance and Care The FX4 PRO should be treated with care and the following suggestions will help maintain your Warranty. 1. Do not use or store the device in dusty or dirty environments. Moving parts and electronic components can be damaged.
-
Page 33: After-Sale Service
9.After-Sale Service For any quality problem or missing accessories, especially pairing problem between 2 or more FX4 PRO headsets, please feel free to contact us at email: We're always here ready to winzon.cs@outlook.com. help, will reply to you in 24 hours.