Related Manuals for Gira HomeServer
Summary of Contents for Gira HomeServer
- Page 1 Gira HomeServer/FacilityServer Information on start-up Gira HomeServer 0529 00 Gira FacilityServer 2075 00...
-
Page 3: Table Of Contents
3.2.1 Programming the Gira HomeServer ............... 3.2.2 Resetting to the factory settings ..............3.2.3 Resetting the firmware to version 4.8 ............3.2.4 Gira HomeServer as a virtual machine ............User interfaces ..................Free visualisation .................... 4.1.1 HSClient......................QuadClient...................... Apps ....................... -
Page 4: Introduction
For easier reading, only the term Gira HomeServer is used in this description. All information relating to the Gira HomeServer applies both to the Gira HomeServer and to the Gira Facili- tyServer. Properties and functions relating specifically to the Gira FacilityServer are marked accordingly. -
Page 5: System Requirements
KNX devices, as well as monitoring of all events, is done via the KNX. The Gira HomeServer is programmed using the “HS Expert” software, which is available free of charge in the download area of the Gira website. This software can be operated on a standard PC with a Microsoft® Windows operating system. -
Page 6: Software Updates
Please install firmware updates at regular intervals, and observe the installation instructions. Important: back up remanent data before updating the firmware! Make sure to save the data to the remanent memory of the Gira HomeServer before updat- ing / upgrading / downgrading the firmware. -
Page 7: Start-Up And Installation
Start-up and installation Start-up and installation To start up the Gira HomeServer, a general distinction must be made between two subject areas: – Setup and connection of the Gira HomeServer – Function test and start-up Important: start-up may only be carried out by a qualified electrician! Connection and start-up of the device may only be carried out by trained and qualified elec- tricians. - Page 8 The network connection has a green and a yellow LED. Both LEDs light up or flash when there is a network connection to the Gira HomeServer. The LEDs only flash when the Gira HomeServer is switched on. A valid IP address is not required.
-
Page 9: Setup And Installation
The Gira HomeServer may only be set up inside buildings. It is not intended and not approved for mobile operation. Set up the Gira HomeServer at a central location so that connection to the mains voltage, to the network and the KNX is trouble-free. The location should also be ‘out of the way’ so that the device does not impede other work being carried out and so that one of its connections cannot be accidentally interrupted. -
Page 10: Connecting To A Network
(LAN). Please observe that the network distributor and network cable are not included in the scope of delivery. A start-up PC can also be connected directly to a Gira HomeServer using a so-called cross- over network cable. The cable is not included in the scope of delivery. -
Page 11: Connection Test Is Not Successful
2.3.1 Connection test is not successful If the Gira HomeServer is not visible in Windows Explorer, try to address the device via the browser. To do this, use the information from the DHCP server of your network router to determine the assigned IP address. -
Page 12: Operating The Gira Homeserver
Programming a Gira HomeServer With the HS Expert software, the Gira HomeServer is individually programmed to the user’s requirements. In order to be able to use the program quickly and to its full extent, Gira offers (online) training (https://akademie.gira.de/). There are also sample projects that can be found on your PC when the HS Expert is installed. -
Page 13: Resetting To The Factory Settings
The device can be reset to the factory settings via USB stick. The firmware version is used for this, which is part the scope of the HS Expert installation. Afterwards, the Gira HomeServer has the login data as for initial start-up. Note the following: all data on the device is deleted during this process. -
Page 14: User Interfaces
Remote access Via the Gira device portal https://geraeteportal.gira.de/ or a module for remote access (e.g. the Gira S1), Gira provides the option of accessing the Gira HomeServer from outside via the Internet. Among other things, a Dynamic DNS service is available. -
Page 15: Link List
- Monitoring of K. objects (if configured) https://HSIP/license - Licences for components used in the firmware https://HSIP/opt/hsav-gira_en/ - Ajax-Visu Addresses on the Internet: https://akademie.gira.de/ - Online training courses for Gira products https://developer.gira.de/ - Developer information on Gira products 11.2020/V 2.3... - Page 16 Gira Giersiepen GmbH & Co. KG Electrical installation systems Industriegebiet Mermbach Dahlienstrasse 42477 Radevormwald, Germany PO Box 12 20 42461 Radevormwald Germany Tel +49(0)21 95 - 602-0 Fax +49(0)21 95 - 602 -339 www.gira.de info@gira.de...