Advertisement
FLUID TIP SELECTION
Factors to consider in selecting a fluid tip for an air-
assisted airless spray gun include: (1) the size of the parts
being sprayed; (2) the production line speed; (3) the
material flow rate and film thickness; (4) the viscosity of
the material applied; (5) the type of material applied; and
(6) the quality of atomization of the coating required. The
selection of a fluid tip necessary to perform a specific
spraying job is best determined through a combination
of experimentation and expert advice from your material
equipment suppliers.
CHART 1
SPRAY TIP SELECTION
PART NO.
SIZE
113-01706
.017
113-01708
.017
113-01710
.017
113-01712
.017
113-01714
.017
113-01716
.017
113-01718
.017
PART NO.
SIZE
113-01906
.019
113-01908
.019
113-01910
.019
113-01912
.019
113-01914
.019
113-01916
.019
113-01918
.019
PART NO.
SIZE
113-02110
.021
113-02112
.021
113-02114
.021
113-02116
.021
113-02118
.021
PART NO.
SIZE
113-02410
.024
113-02412
.024
113-02414
.024
113-02416
.024
113-02418
.024
PART NO.
SIZE
113-02710
.027
113-02712
.027
113-02714
.027
113-02716
.027
113-02718
.027
With an inlet air pressure of 20 p.s.i., the compliant air cap registers 10 p.s.i. of
atomization air. The MSHTE H.V.L.P. gun operates at high transfer efficiencies
and fully complies with all government regulations for H.V.L.P. spray guns.
FAN WIDTH
4"-6"
6"-8"
8"-10"
10"-12"
12"-14"
14"-16"
16"-18"
FAN WIDTH
4"-6"
6"-8"
8"-10"
10"-12"
12"-14"
14"-16"
16"-18"
FAN WIDTH
8"-10"
10"-12"
12"-14"
14"-16"
16"-18"
FAN WIDTH
8"-10"
10"-12"
12"-14"
14"-16"
16"-18"
FAN WIDTH
8"-10"
10"-12"
12"-14"
14"-16"
16"-18"
Important Regulatory Note
Maximum dynamic gun inlet pressure:
PARTS LIST
Ref.
Replacement
No.
Part No.
1
54-4160
2
54-4980
3
45-10000
•4
GTI-33-K5
5
GTI-425
6
MSV-3-K10
7
----
8
----
9
JGA-4044
•10
JGV-463-K3
11
34411-122-K10
•12
JGA-14-K25
•13
JGA-15-K25
•14
JGS-26-K25
•15
JGS-431-K25
•16
MBD-12-K25
•17
JGS-72-K10
18
JGS-449-1
•19
----
20
----
21
JGS-478
22
JGS-477-1
23
JGA-132
24
MSA-3
25
54-4162
26
JGA-402-E
27
-----
•28
MBD-19-K10
MSA-4-K10
•29
-----
30
JGS-16
31
JGA-4041
32
See Chart 1
• A quantity of necessary parts is included in
Repair Kit KK-5064. This kit should be kept
on hand for service convenience.
A quantity of necessary parts is included in
Soft Seal Kit KK-5065.
Suffixes -K3, -K5, -K10, etc. designate kits of multiple parts.
(Example) GTI-33-K5 is a kit of 5 seals.
20 p.s.i.
SB-2-293-C
Description
Retaining Ring
Air Cap
Nozzle Assembly
Seal Kit (Kit of 5)
Baffle Assembly
Gasket (blue)
Locknut
Fluid Inlet Adapter
3/8" NPS(M)
Fluid Inlet and Nut Kit
Needle Packing Assembly
(Kit of 3)
Fluid Needle Packing Nut
(Kit of 10)
Snap Ring (Kit of 25)
Washer (Kit of 25)
U-Cup (Kit of 25)
Air Valve Assembly (Kit of 25) 1
Spring (Kit of 25)
Gasket (Kit of 10) (Teflon)
PTFE
Air Valve Assembly
Screw
Trigger Bearing Stud
Stud and Screw Kit
(Kit includes 3 studs
and 5 screws)
Trigger, Stud & Screw Kit
(Kit includes 1 each)
Plug
Connector 1/4" NPS
Air Valve Plug
Fluid Needle
Gun Body Bushing
6# Spring (Kit of 10)
4# Spring (Kit of 10)
(Optional)
Spring Pad (included
with #28 and 31)
Fluid Needle Adjusting Screw 1
Bushing, Spring, Knob Kit
Spray Tip Assembly
Page 3
Individual
Parts Req
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Advertisement
