AER Compact XL User Manual page 15

6. Technische Daten, technical specifications
Footswitch connector
footswitch Connector for a dual footwitch
(dual, latching, toggle on-off switch)
Stereo jack socket:
Tip = internal effect on/off
Ring = external effect on/off
Sleeve = common (ground)
Function: Switch ON = effect OFF
Tone controls
channel 1 colour at 700 Hz
at 8 kHz
bass at 100 Hz (shelf type)
middle at 800 Hz
treble at 10 kHz (shelf type)
channel 2
bass at 100 Hz (shelf type)
treble at 10 kHz (shelf type)
Effects
Internal effect Digital effect processor
1 Reverb
2 Reverb with longer predelay
3 Delay (320 ms, repetitive)
4 Chorus
External effect Parallel effect loop, see send and return
effects pan
Blends the effects (internal and external) bet-
ween channels 1 and 2, with reverse direction
of rotation for the external effects.
Power amp
Construction Monolithic IC with DMOS output
Rating Output power (THD = 1%)
Continuous output power is determined by
the limiter, see limiter threshold.
General
Distortion THD + N (6 W / 4 Ω)
measured at loudspeaker terminals
Noise Residual noise (A-weighted),
referred to rated output power:
Acoustical:
Signal / noise ratio:
Analog signal processing
Subsonic filter, adaptive peak limiter
Limiter
threshold
50 W / 4 Ω
2-way system, 8" (200 mm) low-midrange
Speaker system
+ 1" (25 mm) dome tweeter, light-weight
neodymium alloy magnets
Power supply Mains voltage (depending on model):
100, 120, 220, 230, or 240 V~, 50–60 Hz
Power consumption: max. 120 W
Mains fuse Size 5 x 20 mm
Rating
for 220, 230, 240 V models:
for 100, 120 V models:
Operating temperature
Permissible ambient temperature
¼" (6.35 mm)
–3 dB
+10 dB
± 8 dB
±6 dB
±8 dB
±8 dB
±11 dB
200 W / 8 Ω
< 0.1%
–94 dB
approx. 17 dB (A) / 1 m
see input specs
T 1A L 250V
T 2A L 250V
0...35 °C
Cabinet Birch plywood, thickness:
Finish Waterbased acrylic, black spatter finish
Dimensions and weight
Dimensions Height
Width
Depth
Weight 10 kg (22.1lbs)
NOTES
Options configurable by internal jumpers (refer modification
to qualified personnel):
Low-gain option (more headroom) for mic input
Deactivation of 48 V phantom power for mic input
DEFINITIONS
Rated conditions
• Nominal input voltage at input under test
• master fully clockwise
• high / low and colour off
• bass / middle / treble / pan centered
• effects level fully anticlockwise
• gain of unused inputs fully anticlockwise
• gain of input under test adjusted to nominal output voltage
at line out. (This condition corresponds by design to the rated
output power.)
Nominal input voltage: Standard condition for specifications,
if not stated otherwise.
Minimum input voltage: Input voltage required for nominal out-
put with maximum gain and volume settings.
Maximum input voltage: Input voltage that does not cause
distortion more than rated THD+N, suitable control settings
provided.
Nominal output voltage or power refer to rated conditions.
THD + N: Total harmonic distortion + noise, with input voltage
reduced by 10 dB after setting up rated conditions.
Signal / noise ratio: Ratio of output voltage at rated conditions to
output noise voltage with input shorted.
Equivalent input noise voltage: Noise voltage at loudspeaker ter-
minals divided by gain of amplifier. Input shorted after setting
up rated conditions.
Residual noise: Output noise with minimal gain and volume
settings.
Adaptive limiter: Adaptive with respect to power supply.
Maintains constant headroom regardless of power supply
fluctuations.
General: Signal voltages are RMS values. Test signal sine 1 kHz
sine unless stated otherwise. Noise measured from 20 Hz to 20
kHz. Noise stated for a specific input implies that all other inputs
are not used. Sound pressure level (SPL) based on
loudspeaker specification by manufacturer.
Specifications and appearance subject to change without notice.
12 mm (0.47")
320 mm (12.6")
326 mm (12.9")
282 mm 11.1")
15