2.7.2 CONNECTING A CELL PHONE........11 3.6.2 Record a call............25 2.6.2.1 Re-connect a paired phone...........12 2.6.2.2 Set up the level..............12 2.6.2.3 Turn off Bluetooth at the console.........12 4. Solidyne HD3 & HD5 monitoring docks...27 2.7.3 External Hybrid............12 4.1 Features............27 2.8 GPIO.............12 4.2 Connections..........27 2.9 Models /AoIP (optional).......13...
About this manual Introduction Welcome to DX816/DX822 user Manual! REVISION, June 2022 The Solidyne DX816 and DX822 are compact mixing consoles for broadcasting. Its design is solid and ele- What’s in the box gant; with a great flexibility. It includes USB digital I/O which brings digital link with the computer;...
Into the Studio, a headphone amplifier (optional 1.5 ETM – VCA faders item Solidyne HD3 & HD5) is in charge of manage the signals of the loudspeakers monitors and head- The faders are “feather touch” with the technique phones (see 2.5.1 –...
Tally light output ([2] in Fig.2) gives 12V/150 mA Orange when the Master MIC-on is turned on (supports Green / White two Solidyne LA-100 on-air sign). In addition, the Blue Blue / White console has a built-in tally light. Green Brown / White THE OUTPUT “TALLY LIGHT”...
/AoIP. Phantom power is not available on MIC-2b, MIC-3b, It is a balanced analog output that sends decoded MIC-5b and MIC-6b. audio from incoming streaming. Page 8 DX816 & DX822 - Broadcast mixing consoles SOLIDYNE...
RJ45 to RJ45 shielded patch (code software and in editing and others software that SOL-P50) the monitoring docks Solidyne Studiobox are in use. If the computer does not have in- HD3 and HD5 (optional).
MONITOR output. The pin-out used is not compatible with StudioHub wires. For more information please see “4.- Monitoring docks Solidyne HD3 & HD5. Figure 7: Connection of loudspeakers and headphones 2.7.3.1 Monitoring setup without Solidyne into the Studio using a standard headphone amplifier.
2.7.2 CONNECTING A CELL PHONE When the searching ends, look for the • Any Bluetooth cell phone can be linked to Solidyne DX816/822 Bluetooth device, which will ap- DX822. While the phone can be up to 5 meters pear as Solidyne BTM641. If the cell phone...
The DX816/822 series has send and return for ex- ternal hybrid. “External Hybrid” [8] uses a female ¼” TRS (Jack) that send signal (PGM) through the “tip” and receives signal (return or input to console) through the “ring”. Page 12 DX816 & DX822 - Broadcast mixing consoles SOLIDYNE...
/AoIP allows to stream the PGM signal (models with only one AoIP) or PGM and REC (models with The file IP.exe is a software setup that installs the “Solidyne double AoIP). The AoIP module allows: Multi-Discovery. Look for leame-readme.txt and follow the indica- tions according the case.
The firmware can be settled to decode an incoming dio quality is defined in the CODER side. streaming; for example, a streaming generated from other Solidyne device (series 2600/IP; DX816; 2.9.6.1 Audio from incoming streaming DX822; Unidex UX24 and ADA102 coder). The en-...
Equipment with AoIP option - Tutorial for firmware update and connection to shoutcast.pdf In where RTP is the protocol used by the Solidyne DX822/ AoIP; 0.0.0.0 means from any incoming IP and '3030' is the port used. Remember to set the firewall to allow incoming streaming trough port 3030 (or the port that you use).
REC. DX816/822 /AoIP can have up to two Ethernet modules (AoIP) for send/receive audio over IP (PGM and REC). Each AoIP module can receive a SOLIDYNE DX816 & DX822 - Broadcast mixing consoles Page 17...
In the Production Room there will be two phones “Phone-1” and “Phone-2”, each one for B) A producer/telephonist answer the calls. a phone line in the console; and the mobile phone. Page 18 DX816 & DX822 - Broadcast mixing consoles SOLIDYNE...
The red LED in phone line buttons only lights with tion in the audio signal that goes to air. So in Solidyne active phone lines. If the line is not connected, the hybrids we use a processed return channel, to avoid LINE button not lights.
Note that the Solidyne Hybrid on- air audio qual- To answer from DX822, make a short touch • ity of the local journalists is ever perfect and without on the button “BLUETOOTH” (or you can an- any coloration. swer from the cell phone screen).
3.2.6.2 Make a conference between Skype (or similar), land lines and cell phone 3.2.5 Null factor The Solidyne DX816/822 allows maximum flexibility to generate a virtual forum between journalists and This adjustment is only for LAND lines. The rejection interviewees, very far apart. Proceed as follows:...
Studio, a headphones amplifier output REC. ON-AIR is for listen an external source, unit must be added. Solidyne offers the modules HD3 usually a tuner to hear the transmission from the and HD5. HD5 manages up to 5 headphones with air.
Each channel has a button “CUE” that allows to listen 3.4.1 Features the signal when that channel is off-air. If CUE is The Solidyne DX816 has 3 mic channels (faders), but pressed in several channels, the signals are mixed. allows to connect up to 5 microphones at the rear At the Control Room, the CUE signal hears in head- panel.
Line channels have gain adjustment that must be settled to obtain 0VU with the fader working above The Solidyne DX822 has four stereo LINE channels. the OVL zone (the gray zone between -10 /-20 dB) to Line channels have two stereo inputs. Channels 4 & 5 avoid excessive amplification on preamps.
“3.2 - Hybrid & Telco”. Assign the monitoring to REC the console is on the air. to listen to the communication (see previous issue). SOLIDYNE DX816 & DX822 - Broadcast mixing consoles Page 25...
RJ45 at both ends (pin to pin). This cable The console gives a signal with fixed level to the mon- is provided by Solidyne. The cable connects the “Stu- itoring docks.The signal is switched from the console dio monitor OUT” of DX816/822 (See Figure 6, [7]) (PGM, REC, ON-AIR or CUE).
This Agreement will be operation guarantee (usually 15 years of use). sent by FAX to Solidyne (5411 4702-2375) in paper Please see more information at www.solidynePRO.- letterhead of the radio and signed by its Director or General Manager.
Open collector +24V @ 0,1 A ON-AIR signal output (turns on when MIC is open). Tubular connector 2.1 mm (internal pin). 12 V CC @ 0,15 amp (two Solidyne On-Air lights). FREQUENCY RESPONSES 20-20.000 Hz +/- 0.5 dB (LIN to PGM) POWER SUPPLY Tubular connector 1.8 mm (internal pin).
Need help?
Do you have a question about the DX 816 and is the answer not in the manual?
Questions and answers