Download Print this page
Valcom PagePac PAGEPAL V-5335700 Quick Start Manual

Valcom PagePac PAGEPAL V-5335700 Quick Start Manual

Advertisement

Quick Links

PagePac
by
INTRODUCTION
The PagePal unit interfaces most telephone sys-
tems (PBX, KTS, Centrex) to virtually any public
address audio system.
In addition, PagePal furnishes inputs for customer
provided background music and auxiliary inputs
(such as an attendant microphone, a radio
receiver, recorded announcements). Control
inputs are provided for tones generated by the
PagePal. PagePal can be placed on a desk or
shelf, or mounted to a wall.
Note: Only line level microphones may be used
with PagePal.
SPECIFICATIONS
FEATURES
Telephone Access from:
- Loop start trunk port
- Ground start trunk port
- Analog PBX station, Centrex or CO lines
- Dry loop page ports (4-wire) with contact
closure
Level controls to set attendant input and back-
ground music, relative to telephone level
Simplified connections via modular telephone
jack and lugless terminal block
Power Requirements
Included power supply plugs into standard AC
outlet
Dimensions/Weight
2.5"H x 6.0"W x 4.0"D
(6.4cm x 15.3cm x 10.2cm)
2.0 lbs. (0.9 kg)
Environment
Temperature: 0 to 40°C (32 to 104°F)
Humidity:
Technical Manuals Online! - http://www.tech-man.com
Technical Manuals Online! - http://www.tech-man.com
®
PAGEPAL
V-5335700
5 to 95%
firealarmresources.com
®
OPERATION
Inputs are routed to the output with the following
priority (highest to lowest):
1. Attendant access for emergency announce-
ments.
2. Telephone Access for general paging.
3. Alert Tone 1 (siren) for evacuation warning.
4. Alert Tone 2 (chime) for time clock, door bell,
security alert, etc.
5. Night bell for after-hours calls to ring over the
public address system.
6. Music input for background music.
7. Override or busy tone is returned to the tele-
phone user if a higher priority input is active.
8. Call confirmation and preannouncement tones
may be optioned.
9. An optional contact closure output is provided
to control auxiliary equipment (music/page
switching, recorder logging, etc.).
10. Station access mode features:
- VOX (Voice Operated Switch)
- Maximum length off-hook timer.
- Responds to open loop disconnect).
- Dial tone detection and disconnect.
11. Loop Start Supervised (LSS) access mode
provides VOX and maximum length off-hook
timers for use with a Loop Start Trunk Port.
1
Issue 2
947170

Advertisement

loading

Summary of Contents for Valcom PagePac PAGEPAL V-5335700

  • Page 1 ® PagePac Issue 2 ® PAGEPAL V-5335700 INTRODUCTION The PagePal unit interfaces most telephone sys- tems (PBX, KTS, Centrex) to virtually any public address audio system. In addition, PagePal furnishes inputs for customer provided background music and auxiliary inputs (such as an attendant microphone, a radio receiver, recorded announcements).
  • Page 2: Installation

    427-3900 and ask for PagePac Technical Sup- connect the line if no voice is detected on the port, or call (540) 427-6000 for Valcom 24-hour line for 20 seconds or if the line remains active Automated Support or visit our websites at http:// (off hook) for more than one minute.
  • Page 3 MIC ROPHONE PR EA MP TO LOUD SPEAK ERS MUSIC SOURCE PUBLIC ADDRE SS RECORDED AUD IO SYSTEM ANNOUNCEMENTS TYPICAL INPUTS POWER AMPLIFIER(S) R AD IO R ECEIVER SIGNAL PROC ES SING C ON TR O L C LOSE FOR ATTE NDANT AC CESS STATION OR KEY TELEPHONE SYSTEM,...
  • Page 4 ® Table 1. PagePal J2 Terminal Block Connector Terminal Description Ground for ground start/common connection for Terminals 2-7. Close a contact between this terminal and J2-1 to activate attendant access. Close a contact between this terminal and J2-1 to active TONE 1 (siren). Close a contact between this terminal and J2-1 to activate TONE 2 (chime).
  • Page 5 Table 2. RJ-11 Pinout Pin Number Description Not Used. C1 control input for Dry Loop (Page Port) activation by closure (may also be used for Ground Start grounding point). Ring (– polarity is important for Ground Start). Tip (+ polarity is important for Ground Start). C control input for Dry Loop (Page Port) activation by contact closure.
  • Page 6 Problem Troubleshooting Steps Alert Tone 2 is not functioning. Check the connection to the back panel, pins 1 and 4 of J2. Check the MAIN OUTPUT volume control setting. Verify using an Ohm meter that a contact closure is being provided from the host equipment.