ORiNG IDS-312L Quick Installation Manual

Industrial device server
Hide thumbs Also See for IDS-312L:

Advertisement

Quick Links

Device
Server
Q
I
uick
nstallation

Introduction

The
IDS-312L
is an
innovative secure
port
s
LAN device server with standard features of device server, such like
TCP/IP interface and versatile operation modes: Virtual Com, Serial Tunnel,
TCP Server, TCP Client, and UDP. In addition, the Windows untility, DS-
Tool, could configure multiple devices and set up the mappings of Virtual
Com. On the other hand,
it
can simultaneously transfer data up to 5
redundant host PCs to a
vo
id Ethernet connection breakdown or any host
PC fails. Further,
IDS-312L
feature HTTPS, SSH, and SSL encryption to
s
assure the security of critical data transmission.
232/422/485 and provides dual redundant power inputs, 12~48 VDC, on
terminal block to guarantee a non-stop operation. With wide operating
o
temperature, -10~70 C, and rugged IP-30 housing design, t
operate in the harsh industrial environment. Therefore,
best solution to the high demand of secure serial to Ethernet critical data
communication.
The product is open type, intended to be installed in and industrial control panel or an
enclosure.

Package Contents

The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Contents
Pictures
IDS-312L
CD
QIG
DIN-rail kit
Wall-Mount Kit
4-pin terminal block
Dust cover

Preparation

Before installation, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using
web-based system management tools.
Q I G
IDS-312L
G
uide
Safety & Warnings
one
port RS-232/422/485 to
two
Elevated Operating Ambient: If installed in a closed environment, make sure the
operating ambient temperature is compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation of the
equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment
The device
supports RS-
to the supply circuit and the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
he device
could
* Indoor use and pollution degree II, it must be wiped with a dry cloth for clean up the device and
IDS-312L is
the
label.
* Utilisation en intérieur et degré de pollution II, il faut l'essuyer avec un chiffon sec pour nettoyer
l'appareil et son étiquette.
* Do not block air ventilation holes.
* Ne bouchez pas les orifices de ventilation.
* If the equipment is used in a manner not specified by the manufacturer, the protection provided
by the equipment may be impaired."
* Si l'appareil est utilise d'une maniere non specifiee par le fabricant, la protection qu'il apporte
peut se voir diminuee."
* Shall be mounted in the Industrial Control Panel and ambient temperature is not exceed
70 degree C
* doit être monté dans le panneau de commande industriel et la température ambiante ne doit pas
dépasser 70 degrés C
Number
Dimension Unit =mm (Tolerance ±0.5mm)
X 1
X 1
X 1
Hi
Pull
/Low
Res.
Term.
X 1
IDS-312L
X 2
X 1

Panel Layouts

Front Panel
X 2
1
2
2
3
4
7
Pull
5
Hi
/Low
Term.
Res.
6
1907-2XX
IDS-312L
Rear Panel
1. Power status indicators
2. LAN connection status
2
1. Din-rail screw holes
indicators
2. Wall-mount screw holes
3. Serial signal reception
status indicator
4. Serial signal transmission
1
status indicator
5. Dip switch button
6. Ethernet port
2
7. Serial port
PRINTED ON RECYCLED PAPER
Industrial Device Server
Top Panel
1
2
1. Terminal block
2. Reset button

Installation

DIN-rail

Step 1 : Slant the device and screw the Din-rail kit onto the back of the device, right in the
middle of the back panel.
Step 2 :Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into
the rail firmly.

Wall-mount

Step 1: Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A
total of
eight
screws are required, as shown below.
Step 2: Use the device, with wall mount plates attached, as a guide to mark the correct locations
of the four screws.
Step 3: Insert a screw head through middle of the keyhole-shaped aperture on the plate, and
then slide the device downwards. Tighten the screw head for added stability.
Pull
Hi
/Low
Term.
Res.

Network Connection

The device has two 10/100Base-T(X) Ethernet ports. According to the link type, the AP uses
CAT 3, 4, 5, 5e, 6 UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs).
Cable
Type
Max. Length
Connector
10Base-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ45
100Base-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ45
Quick Installation Guide
Version 1.2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IDS-312L and is the answer not in the manual?

Questions and answers

Summary of Contents for ORiNG IDS-312L

  • Page 1 * Indoor use and pollution degree II, it must be wiped with a dry cloth for clean up the device and operate in the harsh industrial environment. Therefore, IDS-312L is ! label. best solution to the high demand of secure serial to Ethernet critical data * Utilisation en intérieur et degré...
  • Page 2 ICMP, IP, TCP, UDP, DHCP, BOOTP, SSH, DNS, SNMP, V1/V2c, HTTPS, SMTP screen. For more information on configurations, please refer to the user manual. For information on Power operating the device server using ORing’s DS-Tool management utility, please go to ORing website. RS-485 RS-485...

Table of Contents