Advertisement
Quick Links
Advertisement
Related Manuals for Ranger design C2-PA18-4
Summary of Contents for Ranger design C2-PA18-4
- Page 1 INSTALLATION GUIDE C2-PA18-4 Partskeeper Cabinet...
-
Page 2: Required Items
QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup............................... 3 - 5 q 1.2 Shelf Assembly..........................6 - 7 Phase 2 - Installation q 2.1 Mark Holes For Plus Nuts....................... q 2.2 Attach Plus Nut..........................9 - 10 q 2.3 Attach Partskeeper Cabinet To the Floor..................11 - 13 REQUIRED ITEMS q Cordless Impact... -
Page 3: Bill Of Materials
60 - 11.875 × 17.5 Shelf Tray, Black Plywood, Usable 12" × 17.5" 94 - 5021 Assembly Fastener Kit 96 - 5021 Install Fastener Kit C2-PA18-4 Installation Guide | REV. A1 | Page 3 For technical support, contact us at 1-800-565-5321... - Page 4 #90-012 Screw 1/4"-10 × 3/4" Serrated Nut 4× 4× 5/16"-18 # 94-116 ZINC 8× 8× #92-102 Screw #14 × 1" Flat Washer 4× 4× # 98-116 5/16" ZINC C2-PA18-4 Installation Guide | REV. A1 | Page 4 For technical support, contact us at 1-800-565-5321...
- Page 5 #94-132 5/16" Plusnut ZINC Lock Washer 4× 4× 5/16" # 98-122 ZINC Spacer 4× 4× 0.375" ID, × 1.0" OD × 0.25" LONG # 98-157 NYLON C2-PA18-4 Installation Guide | REV. A1 | Page 5 For technical support, contact us at 1-800-565-5321...
- Page 6 IMPORTANT: Assemble the partskeeper on a protected clean surface to avoid scratching. TOOLS q Cordless Impact q 3/8" Driver Bit HARDWARE USED 8× 94-5022 #92-102 Screw #14 × 1" C2-PA18-4 Installation Guide | REV. A1 | Page 6 For technical support, contact us at 1-800-565-5321...
- Page 7 1.2.4 Attach 1 partskeeper rail on the bottom of each end panel. TOOLS HARDWARE USED q Ratchet 4× 94-5022 q 3/8" Driver Bit 90-012 Screw 1/4"-10 × 3/4" C2-PA18-4 Installation Guide | REV. A1 | Page 7 For technical support, contact us at 1-800-565-5321...
-
Page 8: Phase 2 - Installation
Mark the 2 holes of each floor bracket on the vehicle floor. NOTE: If you are using Ranger floor, please go to page TOOLS q Marker MARK C2-PA18-4 Installation Guide | REV. A1 | Page 8 For technical support, contact us at 1-800-565-5321... - Page 9 1/2" Drill Bit w/ Drill Collar ( Set at 1/2" ) q Plus Nut Tool ( 5/16" ) HARDWARE USED 4× 96-5013 #94-132 Plus Nut DRILL COLLAR 1/2" ) seT aT C2-PA18-4 Installation Guide | REV. A1 | Page 9 For technical support, contact us at 1-800-565-5321...
- Page 10 1/2" socket until the plusnut locks, then remove the bolt by turning the impact in reverse. FORWARD REVERSE C2-PA18-4 Installation Guide | REV. A1 | Page 10 For technical support, contact us at 1-800-565-5321...
- Page 11 #90-011 Hex Bolt 5/16" × 1-3/4" #98-122 Lock Washer #98-116 Flat Washer #98-157 Spacers ( QTY = G ap beTween floor and end panel #94-132 5/16" Plusnut C2-PA18-4 Installation Guide | REV. A1 | Page 11 For technical support, contact us at 1-800-565-5321...
- Page 12 1" Hole Saw HARDWARE USED 4× 96-5013 #90-011 Hex Bolt 5/16" × 1-3/4" #98-122 Lock Washer #98-116 Flat Washer #98-157 Spacers #94-132 5/16" Plusnut C2-PA18-4 Installation Guide | REV. A1 | Page 12 For technical support, contact us at 1-800-565-5321...
- Page 13 “You have successfully installed your C2-PA18-4 Thank you for doing business with us.” cs@rangerdesign.com For any feedback or suggestions you may have, please contact: C2-PA18-4 Installation Guide | REV. A1 | Page 13 For technical support, contact us at 1-800-565-5321...
Need help?
Do you have a question about the C2-PA18-4 and is the answer not in the manual?
Questions and answers