Table of Contents
Advertisement
Quick Links
OPERATOR MANUAL
IMPORTANT INFORMATION, KEEP FOR OPERATOR
This manual provides information for:
MODELS
BPM-15/30/40E(CE)
ECLIPSE
™
TILTING BRAISING PAN
· Stainless Steel
· Manual Tilt
· Electric Heated
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CONTAINED IN THIS MANUAL.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
WARNING
Improper installation, adjustment, alteration, service
or maintenance can cause property damage, injury or
death. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this
equipment.
NOTIFY CARRIER OF DAMAGE AT ONCE
It is the responsibility of the consignee to inspect the container upon receipt
of same and to determine the possibility of any damage, including concealed
damage. Unified Brands suggests that if you are suspicious of damage to
make a notation on the delivery receipt. It will be the responsibility of the con-
signee to file a claim with the carrier. We recommend that you do so at once.
Manufacture Service/Questions 888-994-7636.
Information contained in this document is known to be current and accurate at the time
of printing/creation. Unified Brands recommends referencing our product line websites,
unifiedbrands.net, for the most updated product information and specifications.
PART NUMBER 153352, REV. D (01/15)
International
ERGONOMIC
888-994-7636, fax 888-864-7636
unifiedbrands.net
Advertisement
Table of Contents
Related Manuals for Unified Brands groen ECLIPSE BPM-15
Summary of Contents for Unified Brands groen ECLIPSE BPM-15
- Page 1 It is the responsibility of the consignee to inspect the container upon receipt of same and to determine the possibility of any damage, including concealed damage. Unified Brands suggests that if you are suspicious of damage to make a notation on the delivery receipt. It will be the responsibility of the con- signee to file a claim with the carrier.
-
Page 2: Important Operator Warnings
IMPORTANT - READ FIRST - IMPORTANT THESE APPLIANCES MUST BE INSTALLED BY A COMPETENT PERSON IN CONFORMITY WITH THE INSTALLATION AND SERVICING INSTRUCTIONS AND NATIONAL REGULATIONS IN FORCE AT THE TIME. PARTICULAR ATTENTION MUST BE PAID TO THE FOLLOWING: I. E. E. REGULATIONS FOR ELECTRICAL INSTALLATIONS ELECTRICITY AT WORK REGULATIONS HEALTH AND SAFETY AT WORK ACT FIRE PRECAUTIONS ACT... - Page 3 IMPORTANT - READ FIRST - IMPORTANT WARNING: THIS BRAISING PAN IS INTENDED FOR USE IN THE COMMERCIAL HEATING, COOKING AND HOLDING OF WATER AND FOOD PRODUCTS, PER THE INSTRUCTIONS CONTAINED IN THIS MANUAL. ANY OTHER USE COULD RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO THE EQUIPMENT AND WILL VOID WARRANTY.
-
Page 4: Table Of Contents
Table of Contents Important Operator Warnings ............ page 2-3 References..................page 4 Equipment Description ..............page 5 Inspection & Unpacking ..............page 6 Installation .................. page 7-8 Assembly & Commissioning ............page 9 Service ................... page 10-17 User Instructions ..............page 18-19 Cleaning.................. -
Page 5: Equipment Description
Equipment Description Groen electric-heated Eclipse Ergonomic Tilting Braising Pans provide a stainless steel pan equipped with patented heat transfer fins, burner/combustion chamber, hand- operated or electric powered tilting mechanism, thermostatic controls, and hinged cover. The appliance serves as braising pan, griddle, fry pan, oven, kettle, bainmarie and food warmer/server, can be adapted for use as a non-pressure steamer and can be used to stir-fry, reheat and saute foods. -
Page 6: Inspection & Unpacking
Inspection & Unpacking CAUTION The unit will arrive completely assembled, wrapped in protective plastic on a heavy skid, SHIPPING STRAPS ARE UNDER TENSION in a heavy cardboard carton. Immediately upon receipt, inspect the carton for damage. AND CAN SNAP BACK WHEN CUT. Report any apparent shipping damage or an incorrect shipment to the delivery agent. -
Page 7: Installation
Installation CAUTION Internal wiring for the Braising Pan is supplied complete. When you receive the unit, INSTALLER MUST VERIFY THAT THE it is ready for connection. A wiring schematic is located inside the control box on the INSTALLATION COMPLIES WITH THE right side of the pan, and in this manual. - Page 8 Installation WATER SUPPLY Not applicable to this appliance except for optional faucets. ELECTRICAL SYSTEM PERFORMANCE Model BPM-15E BPM-30E BPM-40E 7 KW 10.6 KW 14.1 KW 230 Volt Single Phase 30.6 Amp 46 Amp 61.1 Amps 7 KW 10.6 KW 14.1 KW 400 Volt 3-Phase with Neutral 10.2 Amp...
-
Page 9: Assembly & Commissioning
Assembly & Commissioning ELECTRICAL SUPPLY WARNING Before commissioning the appliance, ensure that the electrical installation has been THIS APPLIANCE MUST BE EARTHED. performed in compliance with relevant regulations. See INSTALLATION on page 7. WARNING PRE-COMMISSIONING CHECK DO NOT OVERFILL WITH OIL OR FIRE MAY Remove literature and packing materials from the interior and exterior of the RESULT! unit. -
Page 10: Service
Service SERVICING WARNING NOTE: When replacing wiring connections refer to the wiring schematic in the unit or ELECTRICAL POWER MUST BE SHUT OFF this manual. BEFORE WORK IS DONE ON INTERNAL COMPONENTS. After Servicing Check for correct operation as appropriate (see Operating the Braising Pan on CAUTION page 9). - Page 11 Service Removal of Lights (Turn electricity main OFF) WARNING Remove electrical cabinet top panel assembly and side panel as described DO NOT OVERFILL WITH OIL OR FIRE MAY on page 10. RESULT! Disconnect the electric leads from the lights. Undo and remove the retaining collar which secures the light to the control cabinet.
- Page 12 Service Removal of High Limit Thermostat (Turn electricity main OFF) WARNING This device is set to open the contactor, to prevent oil temperature from DO NOT OVERFILL WITH OIL OR FIRE MAY exceeding 230ºC. Manual intervention is required to reset the control in the RESULT! event of a lockout.
- Page 13 Service Removal of Contactor (Turn electricity main OFF) WARNING Remove electrical cabinet top panel assembly and side panel as described IF THE HIGH LIMIT THERMOSTAT FAILS TO on page 10. CUT OFF AT 230ºC IMMEDIATELY TURN OFF Loosen the screws on terminal to allow removal of the wires. THE POWER.
- Page 14 WIRING SCHEMATICS Service MODEL BPM-15/30E CE, 400V & 230V WITH NEUTRAL OM-BPM-E(CE)
- Page 15 WIRING SCHEMATICS Service MODEL BPM-40E CE, 400V & 230V WITH NEUTRAL OM-BPM-E(CE)
- Page 16 WIRING SCHEMATICS Service MODEL BPM-30E CE, 240V NO NEUTRAL OM-BPM-E(CE)
- Page 17 WIRING SCHEMATICS Service MODEL BPM-40E CE, 240V NO NEUTRAL OM-BPM-E(CE)
-
Page 18: User Instructions
User Instructions Heating and Operation WARNING Check that the electricity main is “ON”. DO NOT OVERFILL WITH OIL OR FIRE MAY Turn the toggle switch (Electrical Cabinet) to the “ON” position. The green RESULT! power light will illuminate. Turn the operating thermostat (Electrical Cabinet) to the desired setting. WARNING Observe that the amber heat light is “ON”. - Page 19 User Instructions To Empty the Pan CAUTION Turn the hand crank on the front of the gear carrier cabinet clockwise to tilt DO NOT OVERFILL THE BRAISING PAN the pan body forward. The pan will stay in position when you stop turning the WHEN COOKING, HOLDING OR CLEANING.
-
Page 20: Cleaning
Cleaning WARNING SUGGESTED TOOLS BEFORE ANY CLEANING OPERATION, A good stainless steel cleaner TURN THERMOSTAT DIAL TO “OFF” TO Brushes in good condition CUT ANY POWER TO THE HEATING Cloth for cleaning controls ELEMENTS. BEFORE CLEANING ANY PART Chlorine sanitizer OTHER THAN THE INSIDE OF THE PAN, Heavy Duty Cleaner (if required) DISCONNECT ELECTRICAL SUPPLY AT... - Page 21 Cleaning CAUTION 11. Following supplier instructions, apply the sanitizing agent after the unit has been NEVER LEAVE A CHLORINE SANITIZER IN cleaned and drained. Thoroughly drain off the sanitizer. CONTACT WITH STAINLESS STEEL SURFACES FOR LONGER THAN 30 12. After the unit has been cleaned, sanitized and drained, let all surfaces air dry MINUTES.
-
Page 22: Maintenance
Maintenance WARNING Your braising pan is designed to require minimum maintenance, but certain parts ELECTRIC POWER ALWAYS SHOULD BE may need replacement after prolonged use. After installation, no user adjustment SHUT OFF BEFORE WORK IS DONE ON should be necessary. If a service need arises, only authorized personnel should INTERNAL COMPONENTS. -
Page 23: Troubleshooting
Troubleshooting Your Groen braising pan will operate smoothly and efficiently if properly maintained. However, the following is a list of checks to make in the event of a problem. If the actions suggested do not solve the problem, call your qualified Groen Service Representative. For the phone number of the nearest agency, call your area Groen representative or the Groen Parts and Service Department. -
Page 24: Parts Lists
Parts List Stand & Foot Assembly Description Part # CASTER KIT (SET OF 2 WITH 146354 BRAKE AND 2 W/O BRAKE) CASTER WITH BRAKE (W/O 146513 FOOT ADAPTER) CASTER WITHOUT BRAKE 146515 (W/O FOOT ADAPTER) NOT SHOWN FOOT ADAPTER 146516 FLANGED FOOT 146521 (W/O FOOT ADAPTER) - Page 25 Parts List Cover & Counterbalance Assemblies Key Qty Description Part # COVER ASSEMBLY, 171217 15 GALLON COVER ASSEMBLY, 160861 30 GALLON COVER ASSEMBLY, 160808 40 GALLON COUNTERBALANCE 162235 ASSEMBLY, 15 GALLON COUNTERBALANCE 145480 ASSEMBLY, 30 GALLON COUNTERBALANCE 144790 ASSEMBLY, 40 GALLON STUD WELD, 012589 1/4”-20 X 1-1/4”...
- Page 26 Parts List Pan and Element Cover Assembly Key Qty Description Part # PAN WELDMENT, 15 162573 GALLON PAN WELDMENT, 30 145654 GALLON PAN WELDMENT, 40 144789 GALLON ELEMENT COVER WELD 162574 ASSY., 15 GALLON ELEMENT COVER WELD 146186 ASSY., 30 GALLON ELEMENT COVER WELD 144343 ASSY., 40 GALLON...
- Page 27 Parts List Trunnion Cover Key Qty Description Part # SCREW TRUSS HEAD 005764 RIGHT TRUNNION SIDE 145688 PANEL NUT HEX 005619 WASHER LOCK 005618 SCREW HEX HEAD CAP 005615 RETAINING RING 124764 FAUCET BRACKET 137738 SCREW, 1/4-20 x 3/8” 125609 TRUSS PILLOW BLOCK BOX 144314...
- Page 28 Parts List Electrical Control Components OM-BPM-E(CE)
- Page 29 Parts List Electrical Control Components Description Part # ASSY, CONTROL PANEL BOX WELDMENT CE MARK BPM-30,40 G/E 160804 FUSE HOLDER TYPE 3 AG 077854 SCREW PAN HEAD #6-32 X 3/8" 009697 FUSE 3.0 AMP TYPE 3 AG 077853 BUSHING, SNAP 3/4 IN ID 000453 1.3 ft EDGE TRIM 007937...
- Page 30 Parts List Manual Tilt Assembly Key Qty Description Part # GEAR CARRIER 002624 SHAFT, HANDWHEEL 144834 GEAR, WORM 128001 GEAR SECTOR 009829 KEY GIB 012031 HANDWHEEL 012061 PIN ROLL 012614 SCREW SET SOCKET 012060 BEARING ROLLER 002790 BEARING SLEEVE 137239 PLUG PIPE 010286 FITTING GREASE 90...
-
Page 31: Service Log
Service Log Model No: Purchased From: Serial No: Location: Date Purchased: Date Installed: Purchase Order No: For Service Call: Date Maintenance Performed Performed By OM-BPM-E(CE)