- Lose Einheit mit Solarzelle und Akku. - Kabel am Motor à 3 oder 5 m (Option). Kontrollieren Sie die Verpackung. 2 • Montageart Es gibt 1 Einbauweise fur die Fixscreen 100 Solar. Square design Square design: loses Solarpaneel Vorbau, vor dem Fenster, mit vollständig Vorbau, vor dem Fenster, mit vollständig...
Vorderseite der Seitenführung zu demontieren. • Unten an den Führungen vermeidet eine Kunststoff- Abdeckplatte, dass die Beim Fixscreen 100 Solar Kunststoff-Führung nach EW1 ist ein Anschluss ans unten fällt. Stromnetz nicht erforderlich. • Steht die Führung unten auf einer horizontalen Oberfläche, dann darf...
Für eine sichere Montage, Wartung und Benützung Ihrer Senkrechtmarkise, sollen die Sicherheitsvorschriften (nicht auf Leitern arbeiten, Sicherheitskleidung und Sicherheitsschuhe trägen…) berücksichtigt werden. Achtung: Entfernen Sie beim Fixscreen 100 Solar EW1 erst nach der Montage die Schutzhülle von der Solarzelle.
Page 6
Fixscreen 100 Solar ® • Bei der Befestigung des Kastens sollen die Befestigungslinien berücksichtigt/benutzt werden (Achten Sie darauf, dass die so nah wie möglich in der Ecke (Oberseite) des Kastens geschraubt wird um jeden Kontakt zwischen dem Tuch und dem Schraubenknopf zu vermeiden).
Page 7
Fixscreen 100 Solar ® Dieser Schritt entfällt bei einem losen Solarpaneel. Verbinden Sie das Motorkabel mit dem Steckverbinder in der Frontkappe. Achten Sie auf die korrekte Position des Hakens. Schließen Sie die Unterseite der Kassette mit Hilfe der 2 Schrauben in Höhe der Seitenkonsolen mit einem Torx-Schlüssel (DIN 7985 TX –...
Schnee auf dem Solarpaneel liegt und die Photozellen nicht durch Vegetation, Über- hänge usw. bedeckt werden. In den unten aufgeführten Situationen raten wir von einer Montage des Fixscreen 100 Solar ab. Unter Umständen kann die Ausführung mit einem losen Solarpaneel in Erwägung gezogen wer- den.
Page 9
® Kann der Fixscreen 100 Solar in allen Ländern eingesetzt werden? Der Fixscreen 100 Solar ist weltweit erhältlich, für Länder zwischen 52° Nord und Süd auf der Karte unten. Dieses Einsatzgebiet wurde von den Vorschriften von Somfy übernommen. Der Fixscreen 100 Solar darf nicht in den mit „nicht möglich“ gekennzeichneten Zonen eingesetzt werden, da die Batterie nicht beständig gegen Temperaturen unter -20 °C ist und daher die Funk-...
EINE ENDABSCHALTUNG MUSS ABER VOM INSTALLATEUR NOCH EINGESTELLT WERDEN! Die Endpunkte (oben und unten) wurden von Renson eingestellt. Der oberen Endpunkt: Wurde von Renson eingestellt wobei die Endschiene, inkl. Abdichtungslippe, nicht mehr sichtbar ist. Eine Endabschaltung muss aber vom Installateur noch eingestellt werden. Abschaltung unterer Endpunkt: Der untere Endpunkt wurde eingestellt bis zu 400 mm von der Kassettenunterseite.
Standards hergestellt werden. • RENSON übernimmt keine Verantwortlichkeit/Garantie falls die Motoren anders angesteuert werden als von Somfy angegeben. • RENSON übernimmt dazu keine Garantie das Protokol der Screenmotoren sei kompatibel zu Automatisation/Domotik. • Geringfügige Abweichungen zwischen den Farbmustern und den Profilen des Sonnenschutz-Screens können im Herstellungsprozess auftreten.
Fixscreen 100 Solar ® 10 • Einstellung Produkt Ihr Screen kann vollständig recycelt werden. Informieren Sie sich bei Ihrer Stadt oder Recycelstation über die lokalen Umweltauflagen. Beim Demontieren des Screens sollen Sie die Installation spannungslos machen. Materialien sollen getrennt werden bei der Vernichtung des Produktes. Brennbare Materialien sollen von nicht brennbaren Materialien getrennt werden bei der Vernichtung des Produktes.
Page 14
Fixscreen 100 Solar ® Table of contents 1 • General ............................................... 2 • Installation method ......................................3 • Installation method 1 ....................................... 4 • Preparation of the empty box ................................5 • Frequently asked questions ..................................6 • Technical specifications ....................................
- 3 m or 5 m cable to motor (optional). Please check if all parts are included in the packaging. 2 • Installation method There is 1 installation method for the Fixscreen 100 Solar. Square design Square design: separate solar panel...
Fixscreen 100 Solar ® 3 • Installation method 1 • Demount the 2-part side channel. • Use an Allen key type 3 for unscrewing the front part of the side channel type ‘G’. • A plastic end cap at the base of the side channel type ‘G’...
For a secure mounting, use and maintenance of your screen, you should take into account sufficient regulations (do not work on ladders and wear safety clothes and shoes). Attention: with the Fixscreen 100 Solar IM1, do not remove the protection from the solar cell until it has been installed.
Page 18
Fixscreen 100 Solar ® • We strongly advise to secure the box to the construction by using counter sunk screws and avoid each contact with the fabric on the left hand side and right hand side • Always secure the box as close as possible at the groove. In case of a width >...
Page 19
Fixscreen 100 Solar ® This step is not required for a separate solar panel. Connect the cable from the motor to the connector in the front cover. Make sure the hook is attached correctly. Close the bottom of the box with the 2 screws at the side supporting end pieces with a Torx key (DIN 7985 TX –...
In below mentioned circumstances Renson recommends not to use the Fixscreen 100 Solar. Possibly the individual solar panel can be used. A cable length of 3 or 5 m is possible to order.
Page 21
Southernlatitude (between 52° N and 52° S). This scope of application is taken from the Somfy instructions. The Fixscreen 100 Solar may not be used in the ‘not possible’ zones because the battery cannot withstand cold temperatures below -20°C, whereby the operation also cannot be guaranteed.
Fixscreen 100 Solar ® 6 • Technical specifications 6.1 • Technical specifications of the motor Power supply 12 V DC (min 11,5 V, max 14 V) Radio frequency 433,42 MHz Index protection rating IP 44 Operating temperature -10°C / +40°C and exceptionally -20°C / +60°C Maximum number of connected RTS control points Maximum number of connected sensors...
The upper and lower end point is adjusted in the factory. Adjusting upper end point: The upper end point is adjusted in the factory of Renson. The bottom bar including sealing strip will no longer be visible. Adjust the upper end point for end use.
• The main connection should be made by a qualified electrician in accordance with applicable standards. • RENSON does not take the liability or gives the warranty on the automatic control system for the motor screen, except the well-known systems of Somfy.
Fixscreen 100 Solar ® 10 • Discard of the product Your screen can fully be recycled. You should inform yourself about the environmental regulations in your city or recycling station. If you demount your screen, it should be tensionless. The materials should be separated by the product’s destruction. Combustible materials should be separated from non-combustible materials by the product’s destruction.
Page 28
All photos shown are for illustrative purposes; the actual product may vary due to product placement. Renson reserves the right to make technical changes to the products described in this brochure. ® The most recent product information, availability, and your local distributor can always be found on www.renson.eu *L2001241*...