Sanyo VCC-MD300 Technical Manual page 18

Communications Protocol
Message
Camera OFF
ID
ON
ID SET (ASCII code)
ID X-Position +
ID X-Position -
ID Y-Position +
ID Y-Position -
AGC COLOR MAX Gain *1
B/W MAX Gain *1
AUTO MAX Gain *1
AGC ON/OFF *2
Max Gain at AGC ON *2
COLOR AGC_OFF Gain +
COLOR AGC_OFF Gain -
B/W AGC_OFF Gain + *1
B/W AGC_OFF Gain - *1
Gain Preset
Gain Direct (COLOR) *1
Gain Direct (B/W) *1
Gain Direct *2
DNR OFF at AGC ON *2
DNR ON at AGC ON *2
Aperture OFF
ON
Aperture V +
Aperture V -
Aperture V Preset
Aperture V Direct
Aperture H +
Aperture H -
Aperture H Preset
Aperture H Direct
Gamma OFF
ON
SMART1
SMART2
Mirror OFF
H-Mirror
V-Mirror
HV-Mirror
Privacy Area Mask OFF
Masking
Area Mask ON
Area Mask Position Clr
Area Mask Position Set
Area Mask Position Center Set A0 10 0A 0p 0q 0r
Mask Area Degree Set *2
Pan/Tilt Pan/Tilt Degree
Degree
Auto Mask Pos. OFF
Auto Mask Pos. ON
STILL OFF
ON
EEPROM EEPROM Access
Access
Baudrate 19200 bps
9600 bps
4800 bps
2400 bps
*1: Only MD400 CS: Checksum
*2: Only MD300 FF: Terminator
A0 15 00 CS FF
A0 15 01 CS FF
A0 15 09 p q r s t
u v w x y z g h

i j k CS FF

A0 15 0B CS FF
A0 15 0C CS FF
A0 15 10 CS FF
A0 15 11 CS FF
A0 0A 00 0p CS FF
A0 0A 01 0p CS FF
A0 0A 02 0p CS FF
A0 0A 03 0p CS FF
A0 0A 09 0p CS FF
A0 0A 0B CS FF
A0 0A 0C CS FF
A0 0A 0D CS FF
A0 0A 0E CS FF
A0 0A 0F CS FF
A0 0A 12 0p CS FF
A0 0A 13 0p CS FF
A0 0A 13 0 CS FF
A0 0A 14 CS FF
A0 0A 15 CS FF
A0 0B 00 CS FF
A0 0B 01 CS FF
A0 0B 0B CS FF
A0 0B 0C CS FF
A0 0B 0F CS FF
A0 0B 13 0p CS FF
A0 0B 15 CS FF
A0 0B 16 CS FF
A0 0B 19 CS FF
A0 0B 1D 0p CS FF
A0 0C 00 CS FF
A0 0C 01 CS FF
A0 0C 02 CS FF
A0 0C 03 CS FF
A0 0D 00 CS FF
A0 0D 01 CS FF
A0 0D 02 CS FF
A0 0D 03 CS FF
A0 10 00 0p CS FF
A0 10 01 0p CS FF
A0 10 05 0p CS FF
A0 10 09 0p 0q 0r 0s 0t 0u
0v 0w 0x CS FF

0s 0t CS Sets the mask to the center of the optical axis.
FF

A0 10 11 0p 0q 0r 0s 0t 0u
0v CS FF

A0 11 00 0p 0q 0r 0s 0t 0u
CS FF

A0 11 0A CS FF
A0 11 0B CS FF
A0 12 00 CS FF
A0 12 01 CS FF
A0 19 01 0p 0q 0r 0s 0t CS Writes the values to the EEPROM
FF

A0 1A 00 CS FF
A0 1A 01 CS FF
A0 1A 02 CS FF
A0 1A 03 CS FF
Camera ID display
Camera ID settings
Setting the positioning of the Camera ID display (horizontal)
Setting the positioning of the Camera ID display (vertical)
AGC MAX Gain settings during COLOR (0:AGC OFF, 1: -6dB, 2: 0dB, 3: 6dB, 4: 9dB)
AGC MAX Gain settings during B/W (0:AGC OFF, 1: -6dB, 2: 0dB, 3: 6dB, 4: 9dB, 5:12dB, 6:15dB)
AGC MAX Gain settings during AUTO (4: 9dB, 5:12dB, 6:15dB)
AGC ON/OFF switch (invalid during D/N AUTO) (0:OFF, 1:ON)
AGC MAX Gain settings during AUTO (0: -6dB, 1: 0dB, 2: 6dB, 3: 9dB)
Gain settings when COLOR and AGC are OFF (Initial value: 0dB)
Gain settings when B/W and AGC are OFF (Initial value: 0dB)
Returns gain settings when AGC is OFF to factory defaults
(D/N camera is both COLOR and B/W) (Initial value: 0dB)
Gain settings when COLOR and AGC are OFF
(0: 0dB, 1: 3dB, 2: 6dB, 3: 9dB, 4: 12dB, 5: 15dB, 6: 18dB, 7: 21dB, 8: 24dB, 9: 27dB, 10: 30dB)
Gain settings when B/W and AGC are OFF
(0: 0dB, 1: 3dB, 2: 6dB, 3: 9dB, 4: 12dB, 5: 15dB, 6: 18dB, 7: 21dB, 8: 24dB, 9: 27dB, 10: 30dB)
Gain setting when AGC is OFF
(0: 0dB, 1: 3dB, 2: 6dB, 3: 9dB, 4: 12dB, 5: 15dB, 6: 18dB, 7: 21dB, 8: 24dB, 9: 27dB, 10: 30dB)
DNR ON/OFF
Vertical contour compensation settings
Returns vertical contour compensation settings to factory defaults (Initial value: 8)
p: Vertical contour compensation settings 1-15 (Initial value: 8)
Horizontal contour compensation settings (Initial value: 8)
Returns horizontal contour compensation settings to factory defaults (Initial value: 8)
p: Horizontal contour compensation settings 1-15 (Initial value: 8)
Gamma OFF (1)
Gamma ON (0.45)
Gamma SMART1 (Increases the contrast of dark sections)
Gamma SMART2 (Further increases the contrast of dark sections)
Canceling Inversions
Horizontal inversion (Cancels vertical inversion)
Vertical inversion (Cancels horizontal inversion)
Vertical and horizontal inversions
p: Mask number 1-8 (ALL OFF when 0)
p: Mask number 1-8 (ALL ON when 0)
p: Mask number 1-8 (ALL CLEAR when 0)
*Only the "Position setting" is cleared. To make the mask display off, set the Area mask to OFF.
Refer to "Function Descriptions [11]Privacy Mask Setting"
p: Mask No 1-8, qrs: Pan Degree tuv: Tilt Degree
Current positioning information settings when installing dome camera
pqr: Pan Degree, stu:Tilt Degree
Privacy mask is set to the information of Pan/TiltDegree positioning and is not moved
Privacy mask is set to the information of Pan/TiltDegree positioning and is moved
Sets the current image to still.
pqr: Address 0-2047 st: Data 0-255
UART communication speed settings
Enables after camera restart
− 17 −
Model: VCC-MD400/300
(Note 5)
(Note 9)