Command List For Md400 And 300 - Sanyo VCC-MD300 Technical Manual

Communications Protocol

[5] Command List for MD400 and 300

Message
System CAMERA TYPE Unit
CAMERA TYPE Dome
CAMERA TYPE Zoom
All Initial
All Menu Initial
Lens Initial
Reset
Menu Initial
Zoom Tele
Wide
Tele/Wide Stop
Tele/Wide Speed
Direct
Digital Zoom Tele Limiter
V-Reso.UP OFF/ON
VIEW ANGLE Set *1
Zoom Preset ON
Zoom Preset OFF
Focus Auto Focus ON
Manual Focus ON
One Push Trigger
Far
Near
Far/Near Stop
Far/Near Speed
Direct
Near Limiter
Auto Focus Sensitivity
Focus Area
White ATW
Balance MWB
One Push Trigger (AWC Set)
AWC Reset
ATW Smart OFF/ON
MWB Red +
MWB Red -
MWB Red Preset
MWB Red Direct
MWB Blue +
MWB Blue -
MWB Blue Preset
MWB Blue Direct
ATW Masking OFF
ATW Masking ON
ATW Mask Area Clr
ATW Mask Area Set
Iris Auto IRIS
Manual IRIS (EI OFF)
Manual IRIS (EI ON)
Iris Level +
Iris Level -
Iris Level Preset
Iris Level Direct
Manual Iris Stop +
Manual Iris Stop -
Manual Iris Stop Preset
Manual Iris Stop Direct
*1: Only MD400 CS: Checksum
*2: Only MD300 FF: Terminator
A0 01 01 00 CS FF
A0 01 01 01 CS FF
A0 01 01 02 CS FF
A0 01 0A CS FF
A0 01 0B CS FF
A0 01 0C CS FF
A0 01 0D CS FF
A0 01 0E CS FF
A0 02 05 CS FF
A0 02 06 CS FF
A0 02 07 CS FF
A0 02 08 0p CS FF
A0 02 09 0p 0q 0r CS FF
A0 02 18 0p CS FF
A0 02 1F 0p CS FF
A0 02 23 0p CS FF
A0 02 28 CS FF
A0 02 29 CS FF
A0 03 00 CS FF
A0 03 01 CS FF
A0 03 03 CS FF
A0 03 05 CS FF
A0 03 06 CS FF
A0 03 07 CS FF
A0 03 08 0p CS FF
A0 03 09 0p 0q 0r CS FF
A0 03 0E 0p CS FF
A0 03 10 0p CS FF
A0 03 13 0p CS FF
A0 04 00 CS FF
A0 04 01 CS FF
A0 04 03 CS FF
A0 04 04 CS FF
A0 04 06 0p CS FF
A0 04 0B CS FF
A0 04 0C CS FF
A0 04 0F CS FF
A0 04 13 0p 0q CS FF
A0 04 15 CS FF
A0 04 16 CS FF
A0 04 19 CS FF
A0 04 1D 0p 0q CS FF
A0 04 28 CS FF
A0 04 29 CS FF
A0 04 2D CS FF
A0 04 31 0p 0q 0r 0s 0t 0u
0v 0w 0x 0y 0z 0n CS FF

A0 05 00 CS FF
A0 05 01 CS FF
A0 05 02 CS FF
A0 05 0B CS FF
A0 05 0C CS FF
A0 05 0F CS FF
A0 05 13 0p 0q CS FF
A0 05 15 CS FF
A0 05 16 CS FF
A0 05 19 CS FF
A0 05 1D 0p CS FF
Sanyo Dome Camera ID
Sanyo Dome Camera ID
Initialization of Unadjusted EEPROM Values (Set to Factory Defaults)
Initialization of All Menu Settings
Detection of initial lens position
Restarting camera (Saves the setting value)
Initialization of menu settings other than privacy mask settings
p: Speed 1-4 during Tele and Wide commands (1: Slow-4: Fast [Initial value: 3])
pqr: Direct Position
・MD400, 0: Wide, 1829: 22x (optical), 2069: 352x (digital)
・MD300, 0: Wide, 2248: 22x (optical), 2488: 352x (digital)
Digital Zoom Tele Limiter command needs to be sent before moving to digital zoom field.
p: Maximum digital zoom magnification (0: x0 [Initial value], 1: x2, 2: x4, 3: x8, 4: x16)
p: Increased vertical sensitivity settings during digital zoom OFF/ON (0: OFF, 1: ON)
p: Vignette Reduction Mode Settings (0: OFF, 1: OVER0・1.05x, 2: OVER1・1.06x,
3: OVER 2・1.07x, 4: OVER 3・1.08x, 5: OVER4・1.09x, 6: OVER5・1.10x) (Initial value: 0)
Moves the zoom position to the optical TELE edge
Returns the zoom position to the position before the "Zoom Preset ON" operation
Operates the auto focus operation once
p: Speed 1-4 during Far and Near commands (1: Slow-4: Fast (Initial value: 2))
pqr: Direct Position (VCC-MD400 0:Far 3524:Near VCC-MD300 0:Far 4008:Near)
p: Subject distance limit during auto focus and manual focus
(0: 10 cm, 1: 30cm, 2: 50 cm, 3: 1 m [Initial value], 4: 3 m, 5: 5 m)
p: Auto focus restart sensitivity settings (0: LOW, 1: HI [Initial value], 2: HI+)
High+ automatically restarts every 10 seconds (only TELE side) in addition to restarting the change in
subject
Settings Determining Auto Focus Areas 1-3
1: Entire screen-3: Only center of the screen (Initial value: 2)
Auto White Balance Mode (Same as "0" in WB Mode)
Manual White Balance Mode (Same as "1" in WB Mode)
Executes OnePush in AWC Mode
Returns to the original mode only after executing the OnePush Trigger command
Smart ATW (high color saturation compensation) ON/OFF (OFF: 0 [Initial value], ON: 1)
*This mode is valid when WB mode is set to ATW.
Returns MWB red component settings to factory defaults (Initial value: 64)
pq: Direct MWB red components 0-255
Returns MWB blue component settings to factory defaults (Initial value: 64)
pq: Direct MWB blue components 0-255
Mask settings ON/OFF during ATW
Initialization of mask settings during ATW
Mask area settings during ATW
Iris level operation during auto iris
Returns iris levels during auto iris to factory defaults (Initial value: 40)
pq: Iris level 0 (Dark) - 100 (Bright) during auto iris (Initial value: 40)
Aperture operation during manual iris (Initial value: 17)
Returns aperture during manual iris to factory default (Initial value: 17)
p: Aperture 1 (Close) - 17 (Open) during manual iris
− 15 −
Model: VCC-MD400/300
(Note 7)
(Note 7)
(Note 1)