Sanyo VCC-MD300 Technical Manual page 12

Communications Protocol
Message
OSD Zoom Ratio
Zoom Ratio Position
Direction
Direction Position
Set North
Rom Version Display
Camera OFF
ID ON
ID SET (ASCII code)
ID X-Position +
ID X-Position -
ID Y-Position +
ID Y-Position -
Title
Title Set (ASCII code)
Title Position
EEPROM EEPROM Access
Access
Baudrate 19200 bps
9600 bps
4800 bps
2400 bps
38400 bps
ALARM ALARM OUT OFF
ALARM OUT ON
LINE OUT OFF
LINE OUT ON
DAY/ D/N COLOR
D/N BLACK/WHITE
NIGHT
D/N AUTO
D/N BURST OFF
D/N BURST ON
D/N LEVEL SET
D/N ADJ DIRECT (C->B/W)
D/N ADJ DIRECT (B/W->C)
D/N FOCUS SET (AUTO)
D/N FOCUS SET (B/W)
DNR OFF at AGC ON
DNR ON at AGC ON
D/N Filter Slide Time
Stabilizer Stabilizer OFF/ON
Stabilizer Level
Auto Auto Pursuit OFF/ON
Pursuit
Auto Pursuit Sensitivity
CS: Checksum
FF: Terminator
○ : Only MD800/MD600 can be used.
A0 14 00 0p CS FF
A0 14 01 p 0q CS FF
A0 14 02 0p CS FF
A0 14 03 0p 0q CS FF
A0 14 04 0p CS FF
A0 14 10 0p CS FF
A0 15 00 CS FF
A0 15 01 CS FF
A0 15 09 p q r s t u
v w CS FF

A0 15 0B CS FF
A0 15 0C CS FF
A0 15 10 CS FF
A0 15 11 CS FF
A0 15 20 0p CS FF
A0 15 21 p q r s t u
v w CS FF

A0 15 22 0p CS FF
A0 19 01 0p 0q 0r 0s 0t CS Writes the values to the EEPROM
FF

A0 1A 00 CS FF
A0 1A 01 CS FF
A0 1A 02 CS FF
A0 1A 03 CS FF
A0 1A 04 CS FF
A0 1F 00 CS FF
A0 1F 01 CS FF
A0 1F 0A CS FF
A0 1F 0B CS FF
A0 28 00 CS FF ○
A0 28 01 CS FF
○
A0 28 02 CS FF ○
A0 28 03 CS FF ○
A0 28 04 CS FF ○
A0 28 05 0p CS FF ○
A0 28 06 0p CS FF ○
A0 28 07 0p CS FF ○
A0 28 08 0p CS FF ○
A0 28 09 0p CS FF ○
A0 28 14 CS FF
A0 28 15 CS FF
A0 28 16 p CS FF ○
A0 33 00 0p CS FF
A0 33 01 0p CS FF
A0 34 00 0p CS FF
A0 34 01 0p CS FF
p: Zoom magnification display
Zoom magnification display position p: x-position (0-19) q: y-position (0-11) (Initial value: x: 19 y: 11)
p: Orientation / angle information display (1: ON/0: OFF)
Positioning of the orientation / angle information display p: x-position (0-11) q: y-position (0-11) ( (Initial
value: x: 1 y: 11）
p: Setting the current position to the home position (Orientation: North, PAN angle: 0˚)
(1: ON/0: PRESET）
p: Version display (1: ON/0: OFF)
Camera ID display (ON/OFF)
Camera ID settings
Setting the positioning of the Camera ID display (horizontal)
Setting the positioning of the Camera ID display (vertical)
p: Title display (1: ON/0: OFF)
Title settings
p: Positioning of the title display (1: displayed on the next line from the ID / 0: displayed on the same
line)
pqr: Address 0-2047 st: Data 0-255
UART communication speed settings
Enables after camera restart
External alarm output settings (For zoom cameras)
Alarm output settings to controller (For zoom cameras)
Color Mode
Black and White Mode
Color/Black and White Auto Switch Mode
Burst Settings ON/OFF
p: Color/Black and White Switch Level Settings (0: LOW, 1: MID, 2: HIGH, 3: ADJ)
Switch level LOW: Dark – High: Bright ADJ: Manual setting
Switch Level LOW: Dark-HIGH: Bright
ADJ: Manual Settings
p: Color Black and White Switch Level Manual Settings 0-6
Larger value switches darker sections (Initial value: 4)
p: Black and White Color Switch Level Manual Settings 0-6
Larger value switches darker sections (Initial value: 4)
p: Focus mode settings during D/N AUTO black and white, 0: Near infrared wavelength compensation
(MODE1), 1: Corresponds to optical wavelengths (MODE2)
p: Focus mode settings during D/N BLACK/WHITE, 0: Near infrared wavelength compensation
(MODE1), 1: Corresponds to optical wavelengths (MODE2)
DNR ON/OFF
p: Changes the D/N filter slide time. (5 – 20 seconds) [Initial value: 0 seconds]
p: Stabilizer (Stabilizing function) ON/OFF (0: OFF/1: ON) * Only VCC-MD700/800 series
p: Setting the level of the Stabilizer Level (0: Low 1: Middle 2: High) default: 1
* Only VCC-MD700/800 series
p: Auto Pursuit ON/OFF (0: OFF/1: ON)
p: Sets the sensitivity to brightness variation when motion is detected
1-F (High sensitivity – Low sensitivity)
− 11 −
Model: VCC-MD800/700/600/500
(Note 4)
(Note 4)
(Note 6)
(Note 5)
(Note 5)
(Note 3)
(Note 3)