Table of Contents
Advertisement
Communications Protocol
Message
Backlight
BLC OFF
Multi BLC ON
Multi BLC Weight -
Multi BLC Weight +
Multi BLC Weight Preset
Multi BLC Weight Direct
Multi BLC Bright -
Multi BLC Bright +
Multi BLC Bright Preset
Multi BLC Bright Direct
Center BLC ON
Center BLC Weight Preset
Center BLC Weight Direct
Center BLC Area Preset
Center BLC Area Direct
Center BLC Area Display
Mask BLC ON
Mask BLC Area Preset
Mask BLC Area Direct
BLC ON
BLC Mask Display
Shutter
Shutter Speed +
Speed
Shutter Speed -
Shutter Speed Set long
Shutter Speed OFF
Shutter Long Direct
Shutter Short Direct
Sense Up +
Sense Up -
Sense Up Direct
ELS OFF
ELS ON
Motion
Motion Detector OFF
Detector
Motion Detector ON
Motion Size Preset
Motion Size Direct
Motion Size Display
Masking OFF
Masking ON
Mask Area Preset
Mask Area Direct
Motion Mask Display
Sensitivity Move +
Sensitivity Move -
Sensitivity Move Preset
Sensitivity Move Direct
Sensitivity Y-Level +
Sensitivity Y-Level -
Sensitivity Y-Level Peset
Sensitivity Y-Level Direct
Sensitivity Y-Differ +
Sensitivity Y-Differ -
Sensitivity Y-Differ Preset
Sensitivity Y-Differ Direct
Sensitivity Duration +
Sensitivity Duration -
Sensitivity Duration Preset
Sensitivity Duration Direct
Motion Zoom
Motion Interval
CS: Checksum
FF: Terminator
A0 06 00 CS FF
A0 06 01 CS FF
A0 06 04 00 CS FF
A0 06 04 01 CS FF
A0 06 05 CS FF
A0 06 06 0p CS FF
A0 06 07 00 CS FF
A0 06 07 01 CS FF
A0 06 08 CS FF
A0 06 09 0p CS FF
A0 06 0B CS FF
A0 06 0F CS FF
A0 06 10 0p 0q 0r
0s
CS FF Sensitivity settings during Center BLC
A0 06 12 CS FF
A0 06 13 0p 0q 0r
0s
CS FF Center area settings during Center BLC
A0 06 14 0p 0q CS FF
A0 06 15 CS FF
A0 06 19 CS FF
A0 06 1D 0p 0q 0r
0s
0t
0u
0v
0w 0x
0y
0z
0n
CS FF
A0 06 33 CS FF
A0 06 1E 0p CS FF
A0 07 0B CS FF
A0 07 0C CS FF
A0 07 0E 0p CS FF
A0 07 0F CS FF
A0 07 11
0p CS FF
A0 07 12 0p CS FF
A0 07 1A CS FF
A0 07 1B CS FF
A0 07 1D 0p CS FF
A0 07 28 CS FF
A0 07 29 CS FF
A0 08 00 CS FF
A0 08 01 CS FF
A0 08 05 CS FF
A0 08 06 0p 0q CS FF
A0 08 07 0p CS FF
A0 08 0A CS FF
A0 08 0B CS FF
A0 08 0F CS FF
A0 08 13 0p 0q 0r
0s
0t
0u
0v
0w 0x
0y
0z
0n
CS FF
A0 08 14 0p CS FF
A0 08 15 CS FF
A0 08 16 CS FF
A0 08 19 CS FF
A0 08 1D 0p CS FF
A0 08 1F CS FF
A0 08 20 CS FF
A0 08 23 CS FF
A0 08 27 0p CS FF
A0 08 29 CS FF
A0 08 2A CS FF
A0 08 2D CS FF
A0 08 31 0p CS FF
A0 08 33 CS FF
A0 08 34 CS FF
A0 08 37 CS FF
A0 08 3B p
CS FF
A0 08 3D 0p CS FF
A0 08 42 0p CS FF
Backlight compensation OFF
Backlight compensation multifractionated evaluative metering mode (Backlight compensates after
measuring the light of the entire screen.)
Sensitivity settings during Multi BLC
BLC is easier to determine with a larger value (Initial value: 7)
Returns sensitivity during Multi BLC to factory defaults (Initial value: 7)
p: Direct sensitivity settings 0-15 during Multi BLC (Initial value: 7)
Brightness settings during Multi BLC
Larger value increases brightness when determining BLC (Initial value: 7)
Returns brightness settings during Multi BLC to factory defaults (Initial value: 7)
p: Direct brightness settings 0-15 during Multi BLC (Initial value: 7)
BLC center-weighted metering mode (Backlight compensates after measuring the light mainly in the
center.)
Returns sensitivity settings during Center BLC to factory defaults (Each initial value: 0)
* Therefore, Center is always 7
p: Top(0-7) q: Bottom(0-7) r: Left(0-7) s: Right(0-7) (Each initial value: 0)
Returns center area settings during Center BLC to factory defaults (Each initial value: 0)
p: x-position(0-7) q: y-position(0-5) r: x-size(0-7) s: y-size(0-5)
(Initial value: x-position: 2 y-position: 1 x-size: 3 y-size: 3)
*When x-size:0 y-size:0, it becomes 1 area.
Displays the Center BLC Area settings status on the monitor. p: Display (0: OFF, 1: ON),
q: Displayed area (0: CENTER, 1: TOP, 2: BOTTOM, 3: LEFT, 4: RIGHT)
* The area that is not covered with zebra markings shows the setting area.
BLC mask mode (Backlight compensates after measuring the light, ignoring areas set as mask.)
Return mask area settings during Mask BLC to factory defaults
Mask area settings during Mask BLC
Returns to the mode before BLC OFF only when BLC OFF
p: Displays the BLC MASK settings status on the monitor. (1: ON/0: OFF)
Increases shutter speed by one notch (Long time mode x 32 – High speed mode 1/10000)
Decreases shutter speed by one notch (Long time mode x 32 – High speed mode 1/10000)
Shutter Speed Mode Settings
0: Prolonged exposure shutter mode, 1: Normal mode, 3: High speed shutter mode
Returns the shutter speed mode setting to normal mode setting
Shutter speed settings during prolonged exposure shutter mode
(0: x1, 1: x2, 2: x4, 3: x8, 4: x16, 5: x32)
Shutter speed settings during high speed shutter mode
The numbers within the brackets refer to the PAL model
(0: 1/60 [1/50], 1:1/100 [1/120], 2: 1/250, 3: 1/500, 4: 1/1000, 5: 1/2000, 6: 1/4000, 7: 1/10000)
Increase electronic sensitivity settings
p: Direct increased electronic sensitivity settings
(0: OFF, 1: x2, 2: x4, 3: x8, 4: x16, 5: x32)
Sets shutter speed to 1x (1/60 [1/50]) after saving
The numbers within the brackets refer to the PAL model
Returns to electronic shutter speed saved by ELS OFF
Motion sensor ON/OFF
Returns detected motion size settings to factory defaults (Initial value: V-Size: 1, H-Size: 1)
Detected motion size settings p: V-Size (1-6) q: H-Size (1-8) 但し、VxH の MAX 9 (Initial value: V-Size:
1, H-Size: 1)
p: Displays the MOTION SIZE settings status on the monitor. (1: ON/0: OFF)
Mask area settings for motion detection ON/OFF
Returns mask area for motion detection to factory defaults
Mask area settings for motion detection
p: Displays the MOTION MASK settings status on the monitor. (1: ON/0: OFF)
Motion detection sensitivity settings (Initial value: 5)
* Smaller values increase the sensitivity to small movements.
Returns motion detection sensitivity settings to factory defaults (Initial value: 5)
p: Direct motion detection sensitivity settings 1-10 (Initial value: 5)
Minimum brightness settings for motion detection (Initial value: 5)
* Smaller values increase the sensitivity to movements even on dark screens.
Returns minimum brightness settings for motion detection to factory default (Initial value: 5)
p: Direct minimum brightness settings for motion detection 1-10 (Initial value: 5)
Brightness variation settings for undetected motion (Initial value: 5)
* Smaller values increase the sensitivity to movements even with large brightness variation.
Returns brightness variation settings for undetected motion to factory defaults (Initial value: 5)
p: Direct brightness variation settings for undetected motion 1-10 (Initial value: 5)
Continuous movement time for motion detection (Initial value: 1)
* Smaller values increase the sensitivity to fast moving subjects.
Returns continuous movement time for motion detection to factory defaults (Initial value: 1)
p: Direct continuous movement time for motion detection 1-60 (Initial value: 1)
p: Zoom magnification during motion detection (Initial value: 0)
(0: OFF, 1: x1.4, 2: x2, 3: x2.8, 4: x4, 5: x5.6, 6: x 1/1.4, 7: x 1/2, 8: x 1/2.8, 9: x 1/4, 10: x 1/5.6)
p: Interval time until the start of next detection during motion detection (Initial value: 0)
(0: 5s, 1: 10s, 2: 15s, 3: 20s, 4: 30s, 5: 1m, 6: 2m, 7: 3m, 8: 4m, 9: 5m)
− 9 −
Model: VCC-MD800/700/600/500
(Note 1)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 1)
Advertisement
Table of Contents
