Important Safety Instructions - Sanyo LCD-19E3 Instruction Manual

RISK OF ELECTRIC SHOCK DO NOT
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on
or pinched, particularly at plugs, convenience
receptacles, and at the point where they exit from
the apparatus.
11. Only use the attachments/accessories specified by
the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/
appliance combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the appliance has been
damaged in any way, such as when a power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. If an outside antenna is connected to the television
equipment, be sure the antenna system is grounded
so as to provide some protection against voltage
surges and built up static charges. In the U.S.
Selection 810-21 of the National Electrical Code
provides information with respect to proper grounding
of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit,
size of grounding conductores, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrodes.
2
CAUTION
OPENN
T H I S S Y M B O L I N D I C AT E S T H AT D A N G E R O U S
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS RESENT WITH THIS UNIT.
T H I S S Y M B O L I N D I C AT E S T H AT T H E R E A R E
I M P O RTA N T O P E R AT I N G A N D M A I N T E N A N C E
INSTRUCTIONS IN THE OWNER'S MANUAL WITH
THIS UNIT.
16. An outside antenna system should not be located in
the vicinity of overhead power lines or other electrical
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to
keep from touching such power lines or circuits as
contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
GROUND CLAMP
GROUND CLAMPS
NEC
- NATIONAL ELECTRICAL CODE
" Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as
close to the point of cable entry as practical.
17. Wall or Ceiling Mounting - The product should be
mounted to a wall or ceiling only as recommended
by the manufacturer and listed by an independent
laboratory (such as UL).
Apparatus shall not be exposed to dripping or
18. "
splashing and no objects filled with liquides, such as
vases, shall be placed on the apparatus.
19. When the MAINS plug is used as the disconnect
device, the disconnect device shall remain readily
operable.
20. Install the LCD TV in a proper position. If not, it may
result in a fire hazard.
21. Provide appropriate space on the top, sides and rear
of the LCD TV cabinet for allowing air circulation and
cooling the LCD TV.
22. Minimum clearance must be maintained. If the
LCD TV is to be built into a compartment or
similarly enclosed, the minimum distances must be
maintained. Do not cover the ventilation slot on the
LCD TV. Heat build-up can reduce the service life of
your LCD TV, and can also be dangerous.
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
NEC ART 250, PART H)
"