Table of Contents
Advertisement
ITEM NO. QTY.
ITEM NO. QTY.
1
1
4
4
2
2
4
4
3
3
4
4
4
4
8
8
5
5
4
4
6
6
8
8
7
7
2
2
8
8
4
4
9
9
4
4
10
10
4
4
11
11
4
4
1. Position main frame on stands. Use adequately strong stands or heavy wood blocks
to support the main frame about 36" above the floor of the assembly area. Make sure
the frame is stable, secure and reasonably level.
2. Install grease fittings (11) into wings at hinge points.
3. Install LH & RH wings. Lubricate the hinge pins (8) with grease and install as shown.
Retain the pin to the frame with a 5/8 x1 1/2" hex bolt (10) and lock washer (9).
4. Attach barrel ends of cylinders to lugs on main frame with 1" x 3 1/4" head pins (2)
and 1/4" x 1 1/2" cotter pins (5). Install cylinders so that the ports on the rod end are
facing down.
DANGER
5. Attach rod ends of cylinders to lugs on wings with 1" x 5 1/2" pins (3), 1" SAE
washers (4), and 5/16" x 1 1/2" cotter pins (6). Washers go between lugs and cotter
pins.
6. Place wing lock pin (7) in holders provided under wing cylinder lugs and retain pin
with included #9 hairpin. Wing lock pins are under the front two wing cylinders only.
7. Apply grease to all fittings.
12-2007
Air Drill Parts and Assembly Manual
AIR DRILL WING INSTALLATION
PART NO.
PART NO.
HS3536
HS3536
3 1/2" BORE x 36" STROKE HYD. CYLINDER
3 1/2" BORE x 36" STROKE HYD. CYLINDER
GP1600314H04 PIN 1" DIA. x 3 1/4" LG. WITH HEAD
GP1600314H04 PIN 1" DIA. x 3 1/4" LG. WITH HEAD
GP1600512A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES
GP1600512A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES
BF16S
BF16S
1" SAE WASHER
1" SAE WASHER
BSC0415
BSC0415
1/4" x 1 1/2" COTTER PIN
1/4" x 1 1/2" COTTER PIN
BSC0515
BSC0515
5/16" x 1 1/2" COTTER PIN
5/16" x 1 1/2" COTTER PIN
GP1600614C03 1" x 6 1/4" ORANGE HITCH PIN
GP1600614C03 1" x 6 1/4" ORANGE HITCH PIN
GPSPEC24080 1 1/2" x 8 1/4" LG. WING HINGE PIN
GPSPEC24080 1 1/2" x 8 1/4" LG. WING HINGE PIN
BL10
BL10
5/8" LOCKWASHER
5/8" LOCKWASHER
B1015
B1015
5/8 X 1 1/2" PLATED BOLT
5/8 X 1 1/2" PLATED BOLT
GF1610
GF1610
Connect hoses and charge the wing cylinders with
fluid following the procedure in the wing fold
hydraulics section of this manual before connecting
rod ends of the cylinders.
Salford Farm Machinery Ltd.
DESCRIPTION
DESCRIPTION
1/8" NPT GREASE FITTING
1/8" NPT GREASE FITTING
Page 7
Advertisement
Table of Contents
