Return to Contents 2012 9807 Assembly and Parts Manual Wheel Torque Specifications WARNING Maintain proper torque to provide safe and secure attachment of the wheel hub/drum. Improperly tightened wheel nuts can cause the wheel to separate from the wheel mounting surface during operation.
2012 9807 Assembly and Parts Manual Return to Contents Tire Pressure Ratings Ensure proper inflation of each tire for safe operation and extended tire life. Pressure [psi] Pressure [bar] Tire Size 25 [psi] 1.72 [bar] 23.1 x 26 (16 ply) 30 [psi] 2.07 [bar]...
Return to Contents 2012 9807 Assembly and Parts Manual General Safety Precautions Signal Words The words DANGER, WARNING or CAUTION are used with the safety alert symbol. Learn to recognize safety alerts, follow recommended precautions and safe practices. Three words are used in conjunction with the safety-alert symbol:...
Page 7
2012 9807 Assembly and Parts Manual Return to Contents General Safety Precautions DANGER • Wings may fall rapidly causing injury. • Always stay clear of wings when being lowered, raised or in a elevated state. • Always use lockup device provided when raised.
Return to Contents 2012 9807 Assembly and Parts Manual Tongue Installation Page 10 07-2012 Salford Farm Machinery Ltd.
Page 11
2012 9807 Assembly and Parts Manual Return to Contents Tongue Installation ITEM PART NUMBER DESCRIPTION W00271C 9800 300hp TONGUE WELDMENT A60041 570-580-860-870-9700 INNER TELESCOPE A60073 OUTER TELESCOPE 56" A50010 TURNBUCKLE GP1600258H04 PIN 1" DIA. x 2 5/8" LG. WITH HEAD BSC0415 1/4"...
Page 12
Return to Contents 2012 9807 Assembly and Parts Manual THIS PAGE INTENTIONALLY LEFT BLANK : http://texagropark.ru/ Page 12 07-2012 Salford Farm Machinery Ltd.
Return to Contents 2012 9807 Assembly and Parts Manual Axles and Depth Control Axle Installation : http://texagropark.ru/ Page 14 07-2012 Salford Farm Machinery Ltd.
Page 15
2012 9807 Assembly and Parts Manual Return to Contents Axle Installation ITEM QTY PART NO. DESCRIPTION C00174L-KIT 9800 300 hp AXLE LH C00174R-KIT 9800 300 hp AXLE RH GW8000A 8000 lb GREASABLE HUB AND 14" SPINDLE ASSY GW18228 425/65R x 22.5 x 8 BOLT WHEEL - RECAP...
Return to Contents 2012 9807 Assembly and Parts Manual Depth Control Installation 9800 300hp DEPTH CONTROL INSTALLATION Page 18 07-2012 Salford Farm Machinery Ltd.
Page 19
2012 9807 Assembly and Parts Manual Return to Contents Depth Control Installation 9800 300hp DEPTH CONTROL INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION W00176 CTS DEPTH CONTROL BRACKET (AXLE) HPMSC10 STROKE CONTROL VALVE C1008 DETENT ADJUSTABLE STOP C1001 94" DEPTH CONTROL ROD BU1046 U-BOLT 5/8"...
Return to Contents 2012 9807 Assembly and Parts Manual Shank Assembly Shank Assembly Use 90 fittings where shank head plate is near a beam Shank head bolt goes through plate with anti-rotate tab Page 20 07-2012 Salford Farm Machinery Ltd.
Page 21
2012 9807 Assembly and Parts Manual Return to Contents Shank Assembly I I I T T T E E E M M M N N N O O O . . . Q Q Q T T T Y Y Y . . .
Return to Contents 2012 9807 Assembly and Parts Manual Auto Reset Spring Trip Page 24 07-2012 Salford Farm Machinery Ltd.
Page 25
2012 9807 Assembly and Parts Manual Return to Contents Auto Reset Spring Trip ITEM NO. QTY PART NO. DESCRIPTION W00390 TRIP ASSEMBLY B1250T 3/4" NC x 5" TAP BOLT BN12J 3/4" JAM NUT GSE1036B 36 COIL RESET SPRING ASSEMBLY - 3/4"NC HOLE BSR0520 5/16 x 2"...
Page 26
Return to Contents 2012 9807 Assembly and Parts Manual THIS PAGE INTENTIONALLY LEFT BLANK : http://texagropark.ru/ Page 26 07-2012 Salford Farm Machinery Ltd.
2012 9807 Assembly and Parts Manual Return to Contents 9700/9800 SHANK LOCKOUT PROCEDURES Shank Lockout 5 3/4" REMOVE PIN AND HARDWARE MOUNT LOCK-OUT ASSEMBLY ON 2" X 3" TUBE (SEE DIMENSION FROM END OF TUBE) SPRINGS ARE NOT SHOWN 1/2" x 4 1/2" BOLTS...
Return to Contents 2012 9807 Assembly and Parts Manual Disc Gangs Disc Gang Installation 22 23 34 35 34 35 These bolts must be inserted from the bottom : http://texagropark.ru/ Page 28 07-2012 Salford Farm Machinery Ltd.
Page 29
2012 9807 Assembly and Parts Manual Return to Contents Disc Gang Installation ITEM QTY. PART NUMBER DESCRIPTION W00152R 9800 UPPER GANG MOUNT ARM - RH W00152L 9800 UPPER GANG MOUNT ARM - LH W00103 9800 LOWER GANG ARM HS3508DC 3 1/2" BORE x 8" STROKE HYD. CYLINDER - 1 1/2" ROD H2424 1 1/2"...
Page 30
Return to Contents 2012 9807 Assembly and Parts Manual THIS PAGE INTENTIONALLY LEFT BLANK : http://texagropark.ru/ Page 30 07-2012 Salford Farm Machinery Ltd.
2012 9807 Assembly and Parts Manual Return to Contents Coulter Mount Assembly & Rebuild Instructions Use a block of wood to keep from damaging Seal Counterface during insallation. Apply a 1/8" (3mm) bead of RTV sealant 1/2" (13mm) in from the...
Page 32
Return to Contents 2012 9807 Assembly and Parts Manual Coulter Mount Assembly & Rebuild Instructions Install Hub (with pre-assembled Inner Bearing and Seal Counterface), Outer Bearing & Nut. Recommended Install Procedure. Note: Bearings must be properly grease packed. 1. Torque the spindle nut to 100 ft/lbs (135 Nm) to properly seat the bearings in the races.
Page 33
2012 9807 Assembly and Parts Manual Return to Contents Coulter Mount Assembly & Rebuild Instructions Using a punch and hammer, make sure the Dust Cap is EVENLY seated on the hub. After the Dust Cap is installed, grease the hub until grease exits past the seal.
Page 34
Return to Contents 2012 9807 Assembly and Parts Manual Coulter Mount Assembly & Rebuild Instructions Page 34 07-2012 Salford Farm Machinery Ltd.
Page 35
2012 9807 Assembly and Parts Manual Return to Contents Coulter Mount Assembly & Rebuild Instructions ITEM QTY PART NO. DESCRIPTION W00407L 9800 COMPOUND ANGLE COULTER MOUNT - LH W00407R 9800 COMPOUND ANGLE COULTER MOUNT - RH GRASS WRAP GUARD SEAL, GREASE AND DIRT...
Return to Contents 2012 9807 Assembly and Parts Manual 62” Long Harrow Arm Assembly : http://texagropark.ru/ Page 40 07-2012 Salford Farm Machinery Ltd.
Page 41
2012 9807 Assembly and Parts Manual Return to Contents 62” Long Harrow Arm Assembly ITEM NO. QTY. PART NO. DESCRIPTION R30012 PARALLEL LINKAGE BAR R30006 PARALLEL LINKAGE ARM R80099 HEAD,SALFORD HARROW FOR 5/8" UPPER PIVOT BOLT R80100 62" HARROW ARM FOR 5/8" PIVOT AND U-BOLTS R80100A 62"...
Return to Contents 2012 9807 Assembly and Parts Manual 14” Roller Harrow Assemblies : http://texagropark.ru/ Page 44 07-2012 Salford Farm Machinery Ltd.
Page 45
2012 9807 Assembly and Parts Manual Return to Contents 14” Roller Harrow Assemblies 14" ROLLER HARROW ASSEMBLY - 3' 0" (91.4) LONG COMPLETE ASSEMBLY PART NO. MR80143(L/R) ITEM NO. QTY. PART NO. DESCRIPTION ITEM NO. QTY. PART NO. DESCRIPTION R80147R 3' ROLLER ONLY RIGHT HAND SPIRAL, 14" DIA.
Return to Contents 2012 9807 Assembly and Parts Manual Hydraulics & Lights Axle Lift Hydraulics Red extend Red/grey retract Clamp hoses to underside of telescope, to sides of braces, and frame bolts where provided. Route all hoses through back of axle towers...
Page 47
2012 9807 Assembly and Parts Manual Return to Contents Axle Lift Hydraulics HARDWARE ITEM QTY. PART NO. DESCRIPTION HSR5012 5" BORE x 12" STROKE REPHASING CYLINDER HSR4512 4 1/2" BORE x 12" STROKE REPHASING CYLINDER HPMSC10 STROKE CONTROL VALVE H80104P 1/2"...
Return to Contents 2012 9807 Assembly and Parts Manual Disc Gang Hydraulics Black extend Black/grey retract Mount ball valve on telescope - see tongue installation page for mounting bracket and location Pressure reducing valve is mounted on tongue - see tongue installation page for mounting bracket and location.
Page 49
2012 9807 Assembly and Parts Manual Return to Contents Disc Gang Hydraulics HARDWARE ITEM QTY. PART NO. DESCRIPTION HS3508DC 3 1/2" BORE x 8" STROKE CYL. WITH DEPTH CONTROL H8010-5 3/4" NPT MALW PIONEER COUPLER H80104P 1/2" NPT MALE PIONEER COUPLER...
2012 9807 Assembly and Parts Manual Decal Layout 2 PER SHANK 3 PER ARM Salford Farm Machinery Ltd. 07-2012...
Page 53
2012 9807 Assembly and Parts Manual Decal Layout ITEM PART NO. QTY. DESCRIPTION GD100 4" x 16" SALFORD DECAL WITH BLACK BORDER GD101 2" X 9" SALFORD DECAL WITH BLACK BORDER GD102 WWW.SALFORDMACHINE.COM GD10810 GREASE EVERY 10 HOURS GD10840 GREASE EVERY 40 HOURS...