Maintenance - Porter-Cable PCCF920 Instruction Manual

Worklight (Fig. A)
The worklight 4 is activated when the trigger switch is
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Usage (Fig. A)

CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the tool.
Excessive torque may cause breakage and possible
personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press variable speed trigger switch
Release variable speed trigger switch to stop operation.
Always check torque with a torque wrench, as the
fastening torque is affected by many factors including
the following:
Voltage: Low voltage, due to a nearly discharged
‑
battery, will reduce fastening torque.
‑ Accessory size: Failure to use the correct accessory
size will cause a reduction in fastening torque.
Bolt size: Larger bolt diameters generally
‑
require higher fastening torque. Fastening torque
will also vary according to length, grade, and
torque coefficient.
‑ Bolt: Ensure that all threads are free of rust and other
debris to allow proper fastening torque.
Material: The type of material and surface finish of
‑
the material will affect fastening torque.
‑ Fastening time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners
to be overstressed, stripped or damaged.

MAINTENANCE


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your PORTER-CABLE power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
1 to start operation.
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by PORTER‑CABLE, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
PORTER‑CABLE recommended accessories should be
used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact PORTER-CABLE call 1-888-848-5175
or visit our website: www.portercable.com.
Impact Accessories

WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure that
they contain no cracks.
Belt Hook (Fig. G)
Optional Accessory, Sold Separately.

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt hook,
use only the screw 12 that is provided. Be sure to securely
tighten the screw.
The belt hook can be be attached to either side of the
14
tool using only the screw provided, to accommodate left- or
right- handed users. If the hook is not desired at all, it can be
removed from the tool.
1. To move belt hook 14
belt hook in place then reassemble on the opposite side.
2. Be sure to securely tighten the screw
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a PORTER‑CABLE factory service center
or a PORTER‑CABLE authorized service center. Always
use identical replacement parts.
English
, remove the screw that holds the
12 .
9