Related Manuals for Porter-Cable PCC650
Summary of Contents for Porter-Cable PCC650
- Page 1 20v Max* Lithium Jig Saw Batteries and chargers sold separately. *Maximum initial battery pack voltage (measured without a workload) is 20 volts. The nominal voltage is 18. CATALOG NUMBER PCC650...
-
Page 2: Safety Guidelines - Definitions
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. -
Page 3: Jig Saw Safety Warnings
f) Dress properly. Do not wear loose clothing or jewelry. keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. - Page 4 and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber (CCA). Your risk from these exposures varies, depending on how often you do this type of work.
-
Page 5: Important Safety Instructions For Battery Chargers
• Shock hazard. Do not allow any liquid to get inside charger. • Burn hazard. To reduce the risk of injury, charge only designated PORTER-CABLE batteries. Other types of batteries may burst causing personal injury and damage. • Under certain conditions, with the charger plugged in to the power supply, the charger can be shorted by foreign material. -
Page 6: Storage Recommendations
2. Long-term storage will not harm the charger or battery pack (as long as the battery pack is not fully depleted). CHARGING PROCEDURE PORTER-CABLE chargers are designed to charge PORTER-CABLE battery packs. Charge times are: PCC690L and PCC692L in 35-100 mins., PCC691L in 65-200 mins. and PCC695L in 160-300 mins. depending on the pack being charged. 1. Plug the charger into an appropriate outlet before inserting the battery pack. - Page 8 Leaving the Battery in the Charger The charger and battery pack can be left connected with the LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged. This charger features an automatic tune-up mode which equals or balances the individual cells in the battery pack to allow it to function at peak capacity. Battery packs should be tuned up weekly or whenever the battery no longer delivers the same amount of work.
-
Page 9: Flush Cutting
lock-off button is engaged to prevent switch actuation and the battery has been removed. - Hold the saw blade with teeth facing forward. - Holding the saw upside down, push the tool free blade release (3) downward as showin in figure D. - Insert the shank of the saw blade into the blade holder (E1) as far as it will go as showin in figure E. Release the lever. - Check to ensure blade is secure before cutting. ADjUSTING THE SHOE PLATE FOR BEVEL CUTS -FIGURES F, G WARNING: Before attempting any of the following operations, make sure that the lock-off button is engaged to prevent switch actuation and the battery has been removed. -
Page 10: Maintenance
easier operation and longer blade life. For cutting aluminum, kerosene is preferred. RIP & CIRCLE CUTTING Ripping and circle cutting without a pencil line are easily done with the a rip fence and circle guide (available at extra cost). When ripping, slide the rip fence under the screw from either side of the saw. Set the cross bar at desired distance from blade and tighten screw. -
Page 11: Troubleshooting
TROUBLESHOOTING Problem Possible Cause Possible Solution • Unit will not start. • Battery pack not installed properly. • Check battery pack installation. • Battery pack not charged. • Check battery pack charging requirements. • Unit starts immediately • The switch has been • The switch must be moved upon inserting battery. left in the “on” position. to “off” to prevent the tool from immediately starting when battery is inserted • Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into charger until LED lights.
Need help?
Do you have a question about the PCC650 and is the answer not in the manual?
Questions and answers