Related Manuals for Newage BOLD 3.0
Summary of Contents for Newage BOLD 3.0
- Page 1 Accessories BOLD 3.0 48in, 56in, 72in Display Wall Shelf Sets 84” 56” 48” 72” Slatwall Backsplash Kit Slatwall Accessories Kit...
- Page 2 Index 48in, 56in, 72in Display Wall Shelf Sets Slatwall Backsplash Kit Slatwall Accessories Kit...
- Page 3 IM-PB3.03A-02 Pro & Bold Series 3.0 48in, 56in, 72in Display Wall Shelf Sets Warning: Excessive weight hazard! Use two or more people to move, assemble or install shelving to avoid back or other injury. Do not leave children unattended near the shelving. High risk of injury if installed incorrectly: Follow instructions carefully and routinely inspect your system to ensure all components are fastened securely.
-
Page 4: Parts Supplied
Unpacking Thank you for purchasing a NewAge Product! Please give us a call or visit online if • Begin by placing the package on a covered flat surface. you have any questions. • Remove all cardboard, packaging material and clear plastic bags. -
Page 5: Tools Needed
When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the Lifetime of the product. -
Page 6: Weight Capacity
Weight Capacity WARNING: Do not exceed the weight capacity of the wall shelves. Each Shelf has an evenly distributed weight capacity of 250lbs. Each Shelf must be secured between two Locker or Wall Cabinets and attached to the wall. Display Shelf Installation: Note: Cabinets must be installed before installing display shelves Ensure there is 48in/56in/72in between the Wall Cabinets / Lockers depending on your shelf size. - Page 7 Align the top of the shelf with the top of the Wall Cabinet / Locker and insert the 1/4” Hex bolt and washer through the mounting holes and tighten with a lock nut. Repeat to the opposite side. Note: Refer to Installation Tips for installing the top shelf upside down Check and level before securing to Wall.
-
Page 8: Installation Tips
Drill a pilot hole using a 3/16” drill bit. Using a 1/4” x 2-1/2” lag bolt, one 1/4” ID Fender Washer and a 7/16” socket, bolt the Wall Shelf into the Stud. Repeat for remaning studs and second shelf. Parts Needed: Lag Bolt (1/4”dia x 3”) Lag Screw (1/4”... - Page 9 For assistance, call 1.877.306.8930; for U.K 0800.031.4069; e-mail at info@newageproducts.com. ATTENTION: Is your product damaged? STOP Need help or spare parts? For fastest service, contact NewAge Products at 1-877-306-8930; for U.K 0800-031-4069 or support@newageproducts.com. Do not return to the retailer.
- Page 10 • Verify all the contents in the box and gather the required tools. See “Tools Needed”, and “Parts Supplied” list. Thank you for purchasing a NewAge Product! Please give us a call or visit online if you have any questions.
- Page 11 Tools Needed 1 x 12” MagneticLevel 1 x Stud Finder 1 x Tape Measure 1 x #2 Phillips Bit 1 x Pencil 1 x Cordless Power Drill 1 x Hammer Drill 1 x Masonry Bit 3 mm or 1/8” 1 x #2 Phillips head screwdriver Drill Bit [optional for masonry]...
- Page 12 When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the Lifetime of the product.
- Page 13 Parts Supplied 48” Bold / 72” Bold / 56” Pro / 84” Pro / Performance Performance Performance Performance Plus Plus Fixed Bottom Slatwall Section Top Cover Strip Mobile Bottoms Mobile Side Covers #8 Philips pan head screw 2in long Bold / Performance Slatwall Backsplash Parts Top Magnet Cover Slatwall Sections...
- Page 14 Hanging Slatwall Backsplash on Studded Wall Use stud finder to locate the studs Repeat step 1 for each stud and mark the wall with a pencil Determine installation option based on your cabinet series and cabinet configuration Fixed Slatwall Backsplash Mobile Slatwall Backsplash For Cabinets on Feet Continue to Page 7 For Performance Plus Sets on Casters with Mobile...
- Page 15 Installing Backsplash for Fixed Cabinets Place fixed bottom strip tight Pre-drill 3mm (1/8”) holes into each against the wall and the top of the stud then fasten slatwall section to worktop. If your cabinet set does each wood stud with screws provided. not have lower cabinets with a worktop proceed to page 9 Interlock bottom of Slatwall section...
- Page 16 Installing Backsplash with Mobile System Ensure that the Mobile Bottom is tight against the wall and the top Align the side ends of the of the worktop. Pre-drill 3mm (1/8”) slatwall with the side ends of the holes into each stud then fasten worktop Mobile Bottom Strip with screws provided.
- Page 17 Installing Backsplash Without Cabinets Mark the bottom position of the slatwall backsplash by measuring Distance between bottom of wall down from the bottom of the wall cabinets and bottom of slatwall cabinets. The distance is dependent backsplash on the cabinet series and installation type, as shown in the table to the right.
- Page 18 IM-PB3.13A-01 Slatwall 12pc, 20pc, 40pc Multi-Hook Accessory Kit Warning: Excessive weight hazard! Use two or more people to move, assemble or install slatwall to avoid back or other injury. Do not leave children unattended near slatwall or accessories. High risk of injury if installed incorrectly: Follow instructions carefully and routinely inspect your system to ensure all components are fastened securely.
- Page 19 Unpacking Thank you for purchasing a NewAge Product! Please give us a call or visit online if • Begin by placing the package on a covered flat surface. you have any questions. • Remove all cardboard, packaging material and clear plastic bags.
- Page 20 When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the Lifetime of the product.
- Page 21 WARNING: Hook Accessory Installation Only install Accessory Hooks onto securely mounted Slatwalls Standard Installation: Once the Slatwall is installed; install the hook by guiding the top lip into the desired channel. Seat the hook by inserting and resting the lower lip into the channel below. Note: Do not attempt to install accessories upside down.
- Page 22 WARNING: Parts Bin Accessory Installation Only install Accessory Hooks onto securely mounted Slatwalls Standard Installation: Once the Slatwall is installed; install the parts bin by guiding the top lip into the desired channel. Seat the parts bin by inserting and firmly pressing the top lip onto the Slatwall channel. Note: Slatwall accessories will not function properly if installed upside down.
- Page 23 WARNING: Bike Hook Accessory Installation Only install Accessory Hooks onto securely mounted Slatwalls Standard Installation: After properly installing the Slatwall and Bike Hook, guide the bikes front wheel into the hook. Slowly lower the bike as it begins to secure itself on the wall. www.newageproducts.com...
Need help?
Do you have a question about the BOLD 3.0 and is the answer not in the manual?
Questions and answers