Related Manuals for CPI 1132 Series
Summary of Contents for CPI 1132 Series
- Page 1 4096-630 February 03, 2021 ASSEMBLY MANUAL Revision K 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM SATCOM & Antenna Technologies, Inc. 1700 Cable Drive NE Conover, NC 28613 USA t +1 704-462-7330 f +1 704-462-7380...
- Page 2 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM Updated to CPI format. 02/03/21 R.F. Revise text 7/23/19 Revise to Conover Address 4/19/16 General Revision 5-29-07 Del 0185-492 add 0185-491 12/16/04 Revised Az/El to 0185-492 10/12/04 Revised for new reflector 9/3/2003 ORIGINAL RELEASE 3/14/01 REV.
- Page 3 4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132...
-
Page 4: Table Of Contents
4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132 TABLE OF CONTENTS SECTION TITLE INTRODUCTION GENERAL INFORMATION UNPACKING & INSPECTION FREIGHT DAMAGE MATERIAL MISSING OR DAMAGED MECHANICAL INSTALLATION TOOLS FOUNDATION INTERFACE ANTENNA SYSTEM ASSEMBLY REFLECTOR & SUPPORT ASM PART LIST... -
Page 5: Introduction
GENERAL INFORMATION This manual describes the assembly and installation of CPI’s 1.2 meter antenna system. The CPI 1.2 meter is a rugged and reliable mount which will operate in the Ku-Band frequency with high efficiency and at the same time successfully withstand the effects of the environment. -
Page 6: Mechanical Installation Tools
The required interface from the foundation to the mount is 2-1/2" schedule 40 pipe (2.88" O.D.). A suggested in-ground foundation is shown in Figure 1. Also available from CPI, as options, are a kingpost pedestal mount and a non- penetrating mast mount. - Page 7 Minimum depth as shown or extend to local frost line. Foundation meets the design requirements as set forth by the uniform building code. (1982 edition) (CPI DOES NOT REPRESENT OR WARRANT THAT ANY PARTICULAR DESIGN OR SIZE OF FOUNDATION IS APPROPRIATE FOR ANY LOCALITY OR EARTH STATION INSTALLATION.)
- Page 8 4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132 SECTION II REFLECTOR AND SUPPORT ASSEMBLY REFLECTOR AND SUPPORT ASSEMBLY PART LIST- TABLE 2.0 ITEM PART NO. DESCRIPTION VARIES 1.2M Reflector 0185-4332 Az/El Positioner Assembly Hi - Lo Screw 8319-006 MOUNT &...
- Page 9 4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132 CAUTION: During the assembly procedure, the sequence of instructions must be followed. Do Not Tighten Any Hardware Until Instructed. Refer to the parts list table and the referenced steps.
-
Page 10: Feed Support Assembly
4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132 FEED SUPPORT ASSEMBLY NOTE: These instructions are intended as a general reference for feed support assembly. If your antenna system has specific feed support installation instructions, then refer to them at this time. - Page 11 4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132 STEP 1. See Detail A Attach feed rods to reflector with (items: 3, 6, 7 and with [ 2 ] of (item NOTE: The 2.00” flat end of the...
- Page 12 4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132 STEP 3. A). Connect the feed rods to the feed support tube with ( items: 4, 6, 7 ) and with [ 2 ] of ( item 5 ).
-
Page 13: Antenna Pointing
Note: The following alignment procedure is intended only as a general reference guide for this antenna. For proper antenna performance, accurate alignment is critical. Therefore, it is recommended that your own detailed procedure be used or contact CPI’s Technical Support Department for additional recommendations. STEP 1:... - Page 14 4096-630 CPI Satcom & Antenna Technologies 1.2M Ku-BAND Rx/Tx SERIES 1132 Reflector Support Elevation Adjustment Bolt LOOSEN THIS BEFORE ELEVATION ADJUSTMENT TYPICAL BOTH SIDES Tighten canister after rough adjustment Scale “A” for FIGUIRE 2. elevation Fine azimuth adjustment adjustment LOOSEN THIS BEFORE...
-
Page 15: Maintenance
REFLECTOR CPI’s reflector does not require any maintenance. The composite construction of the reflector is virtually impervious to any damages that could be caused by weather or atmospheric conditions. It is only necessary to inspect for any physical damage done by vandalism or very severe weather conditions.