Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
ELECTRICAL SAFETY. F
1.1.
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs
and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate
safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that
an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products
that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the
safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3.
Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4.
Ensure that cables are always protected against short circuit and overload.
1.1.5.
Regularly inspect power supply, leads, plugs for wear and damage and power connections, to
ensure that none is loose.
1.1.6.
Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may require
a fuse smaller than 13 amps for certain products, see fuse rating at right.
1.1.7.
DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8.
DO NOT pull power plugs from sockets by the power cable.
1.1.9.
DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired
by a qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage,
cut off and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the outer insulation extends beyond the cable restraint and that the restraint is tight.
Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD
1.1.10.
fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cores in the cable
is important and should be at least 1.5mm
for others that may be used in the other output sockets, the use of 2.5mm
1.2
GENERAL SAFETY
!
Familiarise yourself with the applications, limitations and specific potential hazards of the product.
F
WARNING! Ensure all Health and Safety, local authority and general workshop practice regulations are strictly adhered to.
F
WARNING! Disconnect from the power supply before changing accessories, servicing or performing any maintenance.
F
WARNING! DO NOT grind or sand any materials containing asbestos.
!
Maintain the machine and keep in good condition (use an authorised service agent).
!
Check the alignment of moving parts regularly, for safest performance keep the machine clean at all times.
!
Before each use check all abrasive attachments for condition. If worn or damaged replace immediately.
!
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts are dangerous and will invalidate the warranty.
!
Locate the machine in a suitable work area. Keep area clean and uncluttered and ensure there is adequate lighting.
!
Ensure the machine is situated on a solid worksurface, adequate for supporting the weight of the machine and the workpiece.
!
Ensure there are no flammable or combustible materials near the work area.
!
Remove ill fitting clothing, ties and loose jewellery and tie back long hair.
!
Maintain correct balance and footing, ensure the floor is not slippery and wear non-slip rubber soled footwear.
!
Keep hands and body clear of the work table when operating the machine.
!
Wear approved safety eye or face protection, when operating the machine. If dust is generated respiratory protection must be worn.
%
DO NOT operate the machine when you are tired, under the influence of alcohol, drugs or intoxicating medication.
%
DO NOT leave the machine running unattended.
%
DO NOT touch the grinding wheel or belt whilst machine is operating, or whilst the machine is plugged into the power supply.
%
DO NOT touch the workpiece immediately after grinding, it will be very hot.
%
DO NOT try to cool the grinding wheel with water or any other lubricants.
%
DO NOT switch the machine on while the workpiece is in contact with the grinding wheel or sanding belt.
%
DO NOT operate the machine if any parts are damaged or missing as this may cause failure and/or personal injury.
%
DO NOT use the machine for any purpose other than that for which it is designed.
%
DO NOT allow children or untrained persons to operate the machine. Keep them away from the work area.
%
DO NOT remove the safety guard whilst in use.
!
When not in use unplug from the power supply and make every effort to make the machine childproof.
3
p
3
WARNING!
It is the user’s responsibility to read, understand and comply with the following:
p
, but to be absolutely sure that the capacity of the cable reel is suitable for this product and
2
INSTRUCTIONS FOR:
COMBINATION BELT SANDER, GRINDER,
WIRE BRUSH & POLISHER.
SM55 & SM56
M o d e l N o s :
B
l
u
e
N
e
u
t
r
a
B
l
u
e
w
i
r
e
N
e
u
t
r
a
w
i
r
e
section is recommended.
2
Y
e
l
l
o
w
&
G
r
e
e
n
E
a
r
t
h
w
i
r
e
Y
e
l
l
o
w
&
G
r
e
e
n
E
a
r
t
h
w
i
r
e
B
r
o
w
n
L
i
v
e
B
r
o
w
n
w
i
r
e
L
i
v
e
l
w
i
r
e
l
C
a
b
l
e
r
e
s
t
r
a
i
n
t
C
a
b
l
e
r
e
s
t
r
a
i
n
t
FUSE RATING
SM55 - 5 AMP
SM56 - 13 AMP
SM55/56 - 0016 - (2) - 230101
Advertisement
Related Manuals for Sealey Quality MACHINERY SM55
Summary of Contents for Sealey Quality MACHINERY SM55
- Page 1 M o d e l N o s : Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.
- Page 2 2. TECHNICAL SPECIFICATIONS Model SM55 Model SM56 Grinding Wheel ....150 x 25 x 20mm Grinding Wheel ....200 x 25 x 20mm Grinding Speed .
- Page 3 93/68/EEC CE Marking Directive For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.