Sealey sM14.V5 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instruction protection
manual
1. saFetY
1.1.

electrical saFetY

WarninG! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable
Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
do not pull or carry the appliance by the power cable.
8
do not pull the plug from the socket by the cable.
8
do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.

General saFetY

familiarise yourself with the applications, limitations and potential hazards of the sander.
9
WarninG! ensure all Health and safety, local authority, and general workshop practice regulations are strictly adhered to.
‰
WarninG! disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.
‰
WarninG! do not sand any materials containing asbestos.
‰
only use for woodworking
9
maintain and keep the sander in good condition (use an authorised service agent).
9
check the alignment of moving parts regularly. for safest performance keep the sander clean at all times.
9
Before each use check all abrasive attachments for condition. If worn or damaged replace immediately.
9
replace or repair damaged parts. use recommended parts only. unauthorised parts are dangerous and will invalidate the warranty.
9
locate the sander in a suitable work area. Keep the area clean, uncluttered and ensure that there is adequate lighting.
9
ensure that the sander is situated on a solid work surface, adequate for supporting the weight of the sander and the workpiece.
9
ensure that there are no flammable or combustible materials near the work area.
9
remove ill fitting clothing, ties and loose jewellery and tie back long hair. Keep hands and body clear of the worktable when operating the
9
sander.
maintain correct balance and footing, ensure that the floor is not slippery and wear non-slip rubber soled footwear.
9
Wear approved safety eye or face protection, gloves, ear defenders and respiratory protection when operating the sander.
9
8 8 do not use the sander for any purpose other than that for which it is designed.
8 8
8 8 do not get the sander wet or use in damp or wet locations or areas where there is condensation.
8 8
do not operate the sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
do not touch the abrasive whilst operating, or whilst sander is plugged into the mains power and avoid unintentional starting.
8
do not switch the sander on while the workpiece is in contact with the abrasive and do not leave the sander running unattended.
8
do not operate the sander if any parts are damaged or missing as this may cause failure and/or possible personal injury.
8
do not allow children or untrained persons to operate the sander. Keep them away from the work area.
8
do not remove the safety guard whilst sander is in use.
8
© Jack sealey limited
instructions for
bench top belt/disc sander
model no:
Wear ear Wear a mask
protection
Original Language Version
sM14.V5
Wear indoor use only
protective
gloves
recommended fuse rating
5Amp
sM14.V5 | Issue 6 (H,F) 06/02/18