Sealey SA35.V2 Instructions

AIR OPERATED 10mm BELT SANDER
PARTS INFORMATION FOR:
SA35.V2
MODEL:
Item Part No. Description
1 SA35/B60G BELT 60G PACK OF 5
1 SA35/B80G BELT 80G PACK OF 5
1 SA35/B100G BELT 100G PACK OF 5
1 SA35/B120G BELT 120G PACK OF 5
12 SA35/93/12 SHOE
13 SA35/93/13 SLOT HEAD SCREW
14 SA35/93/06/14 GUARD SUB ASS'Y
15 SA35/93/06/15 HEX HEAD BOLT
16 SA35/93/16 HEX NUT
17 SA35/93/17 DRIVE PULLEY
44
18 SA35/93/18 HOUSING
19 B/628ZZ BEARING, 628ZZ
2
20 SA35/93/20 END PLATE
4
21 SA35/93/21 SPACER
5
22 SA35/93/22 SUNK KEY
6
23 SA35/93/23 CAP
7
24 B/607ZZ BEARING, 607ZZ
8
25 SA35/93/25 END PLATE
9
26 SA35/93/26 CYLINDER
10
27 SA35/93/27 ROTOR VANE
11
28 SA35/93/28 ROTOR
14
29 SA35/93/29 THROTTLE LEVER
15
30 SA35/93/30 LEVER PIN
40
31 SA35/93/31 VALVE BODY
41
32 SA35/93/32 O-RING
42
33 SA35/93/33 O-RING
43
34 SA35/93/34 O-RING
35 SA35/93/35 VALVE STEM
ISSUE N0: . . . . . . . . . . . .2
ISSUE DATE . . . .24/04/06
Item Part No. Description
36 SA35/93/36 O-RING (SO)
37 SA35/93/37 VALVE SPRING
38 SA35/93/38 AIR DEFLECTOR
39 SA35/93/39 AIR INLET
45 AK93-1.5 1.5mm HEX WRENCH
46 AK93-4 4mm HEX WRENCH
SA35/06-TBA TENSION BAR ASS'Y
SA35/93/06/02 IDLE PULLEY COMPLETE
SA35.V2-04A IDLE PULLEY SHAFT
SA35.V2-05A BRACKET
SA35/93/06/06 TENSION BAR
SA35/93/06/07 HEX SOCKET SCREW
SA35/93/06/08 USE SA35/06-TBA TENSION BAR ASSY
SA35/93/06/09 SPRING
SA35/93/06/10 SPRING PIN
SA35/93/06/11 SPRING
SA35/93/06/14 GUARD SUB ASS'Y
SA35/93/06/15 HEX HEAD BOLT
SA35/93/06/40 TENSION BAR
SA35/93/06/41 SPRING
SA35/93/06/42 LEVER PIN
SA35/93/06/43 LEVER PIN
INSTRUCTIONS FOR
AIR OPERATED 10mm BELT
SANDER
SA35.V2
Model:
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
! WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
! WARNING! Disconnect from air supply before changing accessories or servicing.
Maintain the sander in good condition (use an authorised service agent).
"
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and
"
will invalidate the warranty.
Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
"
Before each use check abrasive belt for condition. If worn or damaged replace immediately.
"
Use only the correct size and type of sanding belt with this sander.
"
Ensure there are no flammable or combustible materials near the work area.
"
! WARNING! Always wear approved eye or face and hand protection when operating the sander.
Use face, dust, or respiratory protection in accordance with COSHH regulations.
"
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
"
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
"
Wear appropriate protective clothing and keep hands and body clear of working parts.
"
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
"
Keep children and unauthorised persons away from the work area.
"
Check moving parts alignment on a regular basis.
"
Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
"
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, rivets, etc.
"
Avoid unintentional starting.
"
! WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
"
that all connections are secure.
Prolonged exposure to vibration from this sander poses a health risk. It is the owner's responsibility to correctly
"
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the sander for a task it is not designed to perform.
#
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
#
! WARNING! DO NOT sand any materials containing asbestos.
DO NOT carry the sander by the hose, or yank the hose from the air supply.
#
DO NOT force, or apply heavy pressure to, the sander, let the sander do the work.
#
DO NOT switch the sander on whilst the belt is in contact with the workpiece.
#
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
#
DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including
#
waste wiping or cleaning rags etc.
DO NOT carry the sander with your finger on the power lever.
#
DO NOT direct air from the air hose at yourself or others.
#
When not in use disconnect from air supply and store in a safe, dry, childproof location.
"
SA35 - 2 - 06/04/06