Sealey SA32.V2 Instructions

Item Part No. Description
Item
1 SA32.V2-01 AIR INLET 28
2 SA32.V2-02 SCREW 29
3 SA32.V2-03 REAR COVER 30
4 SA32.V2-04 SPRING 31
5 SA32.V2-05 O-RING 32
6 SA32.V2-06 VALVE STEM
33
7 SA32.V2-07 VALVE PLUG
34
8 SA32.V2-08 VALVE COLLAR
35
9 SA32.V2-09 OIL COTTON
36
10 SA32.V2-10 OIL COTTON 37
11 SA32.V2-11 GASKET 38
12 SA32.V2-12 FLAT GEAR 39
13 SA32.V2-13 RIVET 40
14 SA32.V2-14 PISTON
41
15 SA32.V2-15 PISTON RING
42
16 SA32.V2-16 CYLINDER
43
17 SA32.V2-17 SCREW
44
18 SA32.V2-18 SPRING PIN 45
19 SA32.V2-19 TRIGGER 46
20 SA32.V2-20 HANDLE 47
21 SA32.V2-21 SCREW 48
22 SA32.V2-22 PLUG
50
23 SA32.V2-23 O-RING
51
24 SA32.V2-24 PIN
52
25 SA32.V2-25 SWITCH
53
26 SA32.V2-26 PALM HANDLE 54
27 SA32.V2-27 BODY
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
PARTS FOR:
TWIN PISTON IN-LINE SANDER
Model: SA32.V2
Issue No: 1
Date Issued: 090904
Part No. Description
SA32.V2-28 FRONT COVER
SA32.V2-29 WIRE CLIP
SA32.V2-30 RIVET
SA32.V2-31 COMPRESSION SPACER
SA32.V2-32 FIXED PLATE
SA32.V2-33 SCREW
SA32.V2-34 FOAM PAD
SA32.V2-35 PAD ASSEMBLY (PARTS 29,30,31,32,34,35)
SA32.V2-36 RIVET
SA32.V2-37 RIVET
SA32.V2-38 PAD PLATE
SA32.V2-39 LOCKING NUT
SA32.V2-40 SIDE GEAR
SA32.V2-41 BRASS PLATE
SA32.V2-42 SCREW
SA32.V2-43 TRANSMISSION GEAR
SA32.V2-44 GEAR SHAFT
SA32.V2-45 SWITCH GEAR
SA32.V2-46 SWITCH SLEEVE
SA32.V2-47 PLATE GUIDE
SA32.V2-48 SCREW
SA32.V2-50 SCREW
SA32.V2-51 RIVET
SA32.V2-52 PLUG
SA32.V2-53 NEEDLE BEARING
SA32.V2-54 FRONT GASKET
01284 757500
www.sealey.co.uk
Web
01284 703534
sales@sealey.co.uk
email
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to
when using this equipment.
p WARNING! Disconnect from air supply before changing accessories or servicing.
Maintain the sander in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and
3
will invalidate the warranty.
Use in suitable, clean and tidy work area, free from unrelated materials. Ensure that there is adequate lighting.
3
Before each use check abrasive for condition. If worn or damaged replace immediately.
3
Ensure the correct abrasive pad size is used.
3
Ensure there are no flammable or combustible materials near the work area.
3
p WARNING! Always wear approved eye or face and hand protection when operating the sander.
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie
3
back long hair.
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure that workpiece is secure before operating the sander. Never hold a workpiece by hand.
3
Check the workpiece to ensure that there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
3
p WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
Keep air hoses away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
3
that all connections are secure.
Prolonged exposure to vibration from this sander poses a health risk. It is the owner’s responsibility to correctly
3
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the sander for a task it is not designed to perform.
7
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
7
p WARNING! DO NOT sand any materials containing asbestos.
DO NOT carry the sander by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to, the sander. Let the sander do the work.
7
DO NOT place attachments close to your face and do not point at other persons or animals.
7
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including
7
waste wiping or cleaning rags etc.
DO NOT carry the sander with your hand on the power lever.
7
DO NOT direct air from the air hose at yourself or others.
7
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
INSTRUCTIONS FOR:
TWIN PISTON IN-LINE SANDER
Model: SA32.V2
01284 757500
www.sealey.co.uk
Web
01284 703534
sales@sealey.co.uk
email
SA32.V2 - 1 - 090904