Sealey SM914 Instructions For

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear eye
instruction protection
manual
1. saFetY
1.1. electrical saFetY
WarninG! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable
Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
dO nOt pull or carry the appliance by the power cable.
8
dO nOt pull the plug from the socket by the cable.
8
dO nOt use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. General saFetY
WarninG! ensure all Health and safety, local authority, and general workshop practice regulations are strictly adhered to.
‰
WarninG! disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.
‰
WarninG! dO nOt sand any materials containing asbestos.
‰
9 ensure the operating voltage stated on the ratings plate corresponds to your mains power supply.
9 check the belt and disc sander and the electrical connections for any damage and dO nOt use the tool if the sander or the cable is
damaged.
9
ensure that the belt and disc sander is switched off before plugging in to the mains power supply.
9 Persons with limited physical, sensory or mental abilities are not allowed to use the unit, unless they are fully supervised and briefed on
safety issues by a qualified person.
9 use the belt and disc sander according to this manual and only for the purpose for which it is designed.
9 Before starting up, make sure that no spanners or adjusting keys are attached to the machine.
9 Avoid contact with grounded surfaces such as radiators, pipes etc.
maintain correct balance and footing, ensure that the floor is not slippery and wear non-slip rubber soled footwear.
9
nOte: remember that the disc and belt will still be moving for several seconds whilst slowing down, after switching off.
9 familiarise yourself with your working area and be alert for possible hazards, which you might not hear due to machine noise.
9
inspect the work piece and remove all nails and screws before sanding.
9 Be aware that sparks may ignite the dust or fumes.
9
Switch off the belt and disc sander before making any adjustments and when the unit is not in use.
9 After finishing work and before carrying out maintenance, disconnect the power lead from the mains supply.
9 in the event of an electrical or mechanical malfunction, immediately switch off the sander and dO nOt use it further.
9 Always keep your work area clean.
9 never use the power cable to carry the belt and disc sander. Keep the cable away from hot, sharp edges and moving parts.
WarninG! Always wear gloves and safety goggles and a dust mask as some coatings and wood dust may be harmful and toxic.
‰
© Jack sealey limited
instructions for
belt/disc sander 915 x 100mm/Ø150 370W/230v
sm914
model no:
Wear ear Wear a mask
protection
Original Language Version
Wear
protective
gloves
recommended fuse rating
13 Amp
sM914 | Issue:2 (H,F) 04/01/18