Advertisement

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SK Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for N-Com SK Series

  • Page 2: Table Of Contents

    13.1.Enabling / disabling the Audio Multitasking function ......................18 13.2.Adjusting the volumes ..................................18 INTERCOM ......................................... 19 14.1.N-Com “600”/”800”/”900” Series Intercom pairing up ......................19 14.2.Pairing up with other N-Com systems ............................19 14.3.Intercom function (one-to-one connection) ..........................20 14.4. Smart Conference (Group Intercom) .............................21 “UNIVERSAL INTERCOM”...
  • Page 3: Warnings And Safety

     When using the N-Com system, comply with all limitations and instructions related to the use of cell phones.  Do not turn on your cell phone or the N-Com system whenever their use is forbidden or when these devices can cause interference or dangerous situations.
  • Page 4: Appropriate Use

    Use the device only in the normal position, as described in the product documentation. Do not attempt to disassemble, tamper with, or modify any part of the N-Com system. Caution: adjust the volume of the N-Com system and of the audio sources connected to it before you use the system on the road.
  • Page 5: Disposal

    1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: ...
  • Page 6: Content Of The Packaging

    CONTENT OF THE PACKAGING The N-Com B802 package contains: N-Com B802 system Speaker (2x) Microphone USB-C wire Microphone foam...
  • Page 7: In-Helmet Installation

    IN-HELMET INSTALLATION Important: before installing the N-Com system, make a note of the attached product identifier code. The installation video can be found at www.n-com.it/en in the Support section. Remove the neck brace (see the helmet’s user manual).  Detach the cheek pads (see the helmet’s user manual).
  • Page 8 Velcro, so that the microphone is at mouth height (Fig. 4). Fig. 4 Warning: ensure that the word “n-com” on the side of the microphone support is facing outward from the helmet (Fig. 5). Warning: to avoid displacement, please attach...
  • Page 9  Remove the protective film from the back of the adhesive keypad by pulling the tab (Fig. 6). NB: the keypad must be completely attached to the shell, avoiding any overlapping at the edges.  Align the keypad’s black cable with the groove running along the edge of the shell (Fig. 7). Important: to avoid problems with opening and closing the chin guard, do not place the keypad cable beyond the groove (Fig.
  • Page 10: System Removal

    Thread the USB-C cable  through the eyelet on the neck brace (Fig. 13). Pass the USB-C cable  through the elastic loop attached to the comfort padding (Fig. 14). Fig. 13 Fig. 14 Arrange the cables and connectors so that they don’t prevent the reinsertion of the comfort ...
  • Page 11: Basic Functions

    BASIC FUNCTIONS Note: before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely.
  • Page 12: N-Com Easyset

    Click on "DOWNLOAD" and save the file in the computer.  Click on "UPDATE" and wait for the firmware update to end.  The release notes of the last Firmware version can be found on the website www.n-com.it – in the “Support”/”Download”/”Software” section.
  • Page 13: Pairing Up Menu

    PAIRING UP MENU All the Bluetooth pairing up operations are carried out in this mode. In order to access the Pairing up Menu starting with the N-Com system switched off, press the “n” key and keep it pressed for 4 seconds.
  • Page 14: Mobile Phone / Mp3 Player Pair Up

     Activate the search of Bluetooth devices on the mobile phone.  Select the N-Com system from the list. If a password is requested, enter the code 0000 (four  zeros). After a few seconds, the connection between the two devices is activated.
  • Page 15: Mobile Phone

    “ Speed Dial ” menu. Saving the Speed Dial numbers To assign one or more speed dialling numbers: To access the Configuration Menu starting with the N-Com switched on, press the “” and “”  keys for 4 seconds. Press the “” or “” key until you hear the voice command “ Speed dial ”.
  • Page 16: Conference Call Function

    Turning off the phone conference During the phone call, briefly press “n”. call function N.B.: “Telephone Conference” function can only be used with the N-Com series “600”/”800”/”900”. 10.3. Smart Navi System The “SMART NAVI SYSTEM” function allows you to listen to navigator directions coming from the smartphone even during an intercom call.
  • Page 17: Music Via Bluetooth

     Activate the search of Bluetooth devices on the navigator.  Select the N-Com system from the list. If a password is requested, enter the code 0000 (four  zeros). After a few seconds, the connection between the two devices is activated.
  • Page 18: Audio Multitasking

    It can be enabled / disabled through the Configuration Menu (chapter 7), the N-Com EASYSET program or the N-Com EASYSET APP. Once the function has been enabled / disabled, the N-Com system needs to be switched off and then switched on to store the selection.
  • Page 19: Intercom

    Put the other N-Com system in “Setting” mode (consult the system user manual).  On B802 system, press the “” key until you reach the option “ Pairing up other N-Com ”.  On B802 system, press the key relating to the “pre-setting position” where you wish to save the ...
  • Page 20: Intercom Function (One-To-One Connection)

    The VOX Intercom function is disabled by default on the device. You can enable / disable the “VOX Intercom” function and set the activation sensitivity, using the N-Com EASYSET program or the N-Com EASYSET APP. If the function is enabled, the system works as follows: The intercom switches on automatically by saying any word out loud into the microphone of one ...
  • Page 21: Smart Conference (Group Intercom)

    The temporary disabling of the VOX function will then be overridden the first time the N-Com device is turned off; and, if the VOX Intercom is enabled (from PC or APP), it will be restored the next time the device is switched on.
  • Page 22: Universal Intercom" Intercom

    UNIVERSAL INTERCOM function 15.1. Pairing up the UNIVERSAL INTERCOM The N-Com system can be paired up to the other intercom (from now on referred to as Intercom B) as if it were a mobile phone. Make sure the B802 is turned off.
  • Page 23: Universal Conference (Chain Intercom)

    Universal Conference (chain intercom) 15.3. The “Universal Conference” mode can be used to connect in conference call N-Com systems of the “800”/“900” series and one system paired up in Universal Intercom mode. The connection procedure is outlined in the diagram provided here below: 1.
  • Page 24: Remote Control

    Note: the “ Universal Conference ” mode can also be used by connecting only “800”/“900” series N- Com systems”. Note: the “ Universal Conference ” mode can also be used by connecting “800”/“900” series N-Com systems with an N-Com system from a different or previous range.
  • Page 25: Battery And Recharge

    N.B.: if you are not planning on using the N-Com system for a long time, you need to fully recharge the device before storing it away. N.B.: if the device is not used for a long time, completely recharge cycle the device at least once every 6 months to avoid possible damage to the battery.
  • Page 26: Summary Table Of Controls

    2 sec Connection CHANNEL 1 Disconnection of active intercom Calling CHANNEL 2 Calling CHANNEL 3 Group intercom connection Group intercom disconnection *Press any key on the N-Com keypad. **Press the keys at the same time. ***Starting with the system switched off.
  • Page 27: Warranty

     Neglect and normal wear and tear of internal and external parts.  Any damage resulting from an accident.  Any modification to or tampering with the helmet or to the N-Com system by the user or third parties.  Use of incompatible accessories not approved by the Manufacturer for the purchased N-Com device model.
  • Page 28: Product Identification

    This warranty does not affect the customer's legal rights under applicable national jurisdiction and the consumer's rights vis-à-vis the dealer under the purchase/sale agreement. 19.4. Product identification N-Com products are identified by means of a code that allows their traceability and identification. The identification code (S/N) can be found on the adhesive label.
  • Page 29 www.n-com.it...

This manual is also suitable for:

B802

Table of Contents