Table of Contents
Advertisement
Quick Links
EN
USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N-Com product.
N-Com B901 was made using the most advanced technology and top-quality materials.
Long-running tests and thorough system development have made it possible to achieve
the highest audio quality.
For additional information on the B901, to download the instructions in PDF format and
install the latest available Firmware version, please visit the website www.n-com.it.
Firmware version: 1.4.x
REFERENCE STANDARDS
The products of the N-Com line are in compliance with standards as per the table below:
B901
Battery
charger
Battery
The Declarations of Compliance can be downloaded from the website www.n-com.it (Download
section).
Model: B901 S
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.; any
use of such marks by N-Com is under license. Other trademarks and trade names are those of their
respective owners.
The Bluetooth system complies with the main safety requirements and
other applicable provisions of Directive RED 2014/53/EU, Directive
2009/65/EC, Directive 2011/65/CE, Directive 2012/19/EU
Directive 2014/35/EU LVD, 2014/30/EU EMC, 2009/125/CE ErP,
2011/65/EU RoHS
Directive 2001/95/CE – GPSD, 2013/56/UE BAT, 2014/30/EU
FCC ID:
Y6MNCOM17
IC:
9455A-NCOM17
R-NZ
Fw 1.4.x-9 - 14/05/2021
Advertisement
Table of Contents
Related Manuals for N-Com S Series B901
Summary of Contents for N-Com S Series B901
- Page 1 R-NZ The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.; any use of such marks by N-Com is under license. Other trademarks and trade names are those of their respective owners. Fw 1.4.x-9 - 14/05/2021...
-
Page 3: Table Of Contents
MUSIC VIA CABLE ..........................17 SATELLITE NAVIGATOR FOR MOTORCYCLES ................17 FM RADIO ............................. 17 INTERCOM ............................18 14.1.N-Com “900”/”600” Series Intercom pairing up ....................18 14.2.Pairing up other N-Com intercoms ........................18 14.3.Intercom function (one-to-one connection) ....................... 19 14.4. -
Page 4: Warnings And Safety
• When using the N-Com system, comply with all limitations and instructions related to the use of cell phones. • Do not turn on your cell phone or the N-Com system whenever their use is forbidden or when these devices can cause interference or dangerous situations. -
Page 5: Appropriate Use
Use the device only in the normal position, as described in the product documentation. Do not attempt to disassemble, tamper with, or modify any part of the N-Com system. Caution: Adjust the volume of the N-Com system and of the audio sources connected to it before you use the system on the road. -
Page 6: Disposal
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: •... -
Page 7: Content Of The Packaging
CONTENT OF THE PACKAGING The N-Com B901 package contains: Electronic plate e-box B901 Rechargeable battery PC connection cable Microphone Key, screw, clamp Microphone foam XL Adhesive Velcro pads Microphone-Stop... -
Page 8: Installation
• Remove the back of the comfort padding by pulling on the neck roll until it separates from the shell. • Temporarily put the padding on the outside of the helmet (Fig. 2). • Remove the N-Com cover from the helmet border gasket. Push from the inside of the helmet to facilitate the removal (Fig. 3). Fig. 1 Fig. -
Page 9: Installing The Microphone
3.2. Installing the system on the helmet • Position the system inside the helmet as shown in figure 11, next to the N-Com housing in the shell. • Looking at the helmet from the outside, slide the rear positioning tab into groove A as shown in the figure. - Page 10 • Insert the microphone connector in the micro USB electronic plate (Fig. 14). • Before you place the speaker in its housing, apply the Velcro pad to the polystyrene cheek pad (Fig. 15). • Position the loudspeaker in the special housing obtained in the polystyrene cheek pad (Fig. 16). •...
-
Page 11: Removing The System
• Now remove the entire system from the helmet. Note: Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. -
Page 12: Basic Functions
4.3. Multi-language voice messages The N-Com system features voice messages that provide information on the system and on the active functions. The language set by default is English. The language of the voice messages may be changed through the specific firmware installable with the N-Com EASYSET program. Please refer to the online HELP for instructions on how to change the language settings. -
Page 13: Configuration Menu
CONFIGURATION MENU All Bluetooth pair ups and other adjustments are carried out in this mode. To put the system in “Configuration mode” (starting from a switched off system) press the “ON” key and keep it pressed for 4 seconds, until you hear the voice announcement “ Configuration Menu ”. -
Page 14: Pairing Up With Mobile Phones Or Other Bluetooth Devices
Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device. • Select the N-Com device. If a password is requested, enter 0000 (four zeros). • Connection between the two devices is established after a few seconds. -
Page 15: Conference Call Function
• On your own mobile phone (paired up and connected to the N-Com system), call the phone number you wish to assign to the selected speed dialling position. The call is interrupted before it goes through, and the selected number will be saved; at this point you will hear the special voice... -
Page 16: Managing Two Mobile Phones (Or Bluetooth Devices)
• Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device. • Select the N-Com system from the list. If a password is requested, enter the code 0000 (four zeros). • After a few seconds, the connection between the two devices is activated. -
Page 17: Sharing Music Via Bluetooth (A2Dp Sharing)
N.B.: Music shared through the intercom can be managed by both systems, for example, both systems can change the track by pressing the relative command. N.B.: the “Music Sharing” function can only be used with the N-Com series “900”/”600”. 11. MUSIC VIA CABLE Connect the mini USB connector of the Multimedia Wire (not included) to the helmet and the other end to the audio device. -
Page 18: Intercom
• Make sure the systems are turned off. • Put the N-Com system in “Setting” mode: press the “ON” key and keep it pressed for 4 seconds, until the blue LED starts to flash quickly. • Put B901 system in “Configuration” mode: press the “ON” key and keep it pressed for 4 seconds, until you hear the voice announcement “... -
Page 19: Intercom Function (One-To-One Connection)
The temporary disabling of the VOX function is then removed the first time the N-Com device is turned off; so, if the VOX is enabled (from PC or APP), it will be restored the next time the device is switched on. -
Page 20: Smart Conference (Group Intercom)
When the conference call ends, all phones automatically reconnect to their own intercom system. Smart Conference Note: The “ ” mode can be used EXCLUSIVELY with “900” series N-Com systems”. Smart Conference Note: The “ ” mode CANNOT be used with systems paired up in Universal Intercom... -
Page 21: Universal Intercom" Intercom
UNIVERSAL INTERCOM function 15.1. Pairing up the UNIVERSAL INTERCOM The N-Com system can be paired up to the other intercom (from now on referred to as Intercom B) as if it was a mobile phone. • Make sure the B901 is turned off. - Page 22 C. Press the relative connection command to start a 4-participant intercom conference call. Universal Conference Note: The “ ” mode can also be used by connecting only “900” series N-Com systems”. Universal Conference Note: The “ ” mode can also be used by connecting “900” series N-Com systems...
-
Page 23: Remote Control
▼ SENA RC4 CENTRAL KEY MULTI-FUNCTION KEY Proceed as follows to pair up the N-Com system to the RC4 Remote Control: • Make sure the RC4 is switched off. • Put the RC4 in pair up mode: press the key “+” and keep it pressed for about 8 seconds. -
Page 24: Battery And Recharge
When the battery is charged, the blue LED goes back to its standard flashing. turned on Note: In case you don’t plan to use the N-Com system for a long time, you need to fully recharge the device before storing it away. -
Page 25: Summary Table Of Controls
Group intercom disconnection Turning on the Radio 2 sec Turning off the Radio 2 sec Automatic search for new station Change station (pre-set stations) Pre-set station 4 sec *Press any key on the N-Com keypad. **Press the keys at the same time. -
Page 26: Warranty
• Neglect and normal wear and tear of internal and external parts. • Any damage resulting from an accident. • Any modification or tampering made to the helmet or to the N-Com system by the user or third parties. • Use of incompatible accessories not approved by Nolangroup for the purchased N-Com device model. -
Page 27: Product Identification
19.4. Product identification N-Com products are identified by means of a code that allows their traceability and identification. The identification code can be found on the adhesive label affixed to the... -
Page 28: Validity Of N-Com Warranty
19.5. Validity of N-Com warranty VALIDITY VALIDITY VALIDITY VALIDITY NATION NATION 2 YEARS 1 YEAR 2 YEARS 1 YEAR ALBANIA LEBANON ALGERIA MACEDONIA SAUDI ARABIA MALAYSIA ARGENTINA MALTA AUSTRALIA MOROCCO AUSTRIA MAURITIUS BAHRAIN MEXICO BELGIUM BRP MONTENEGRO BERMUDA NORWAY BOLIVIA...
Need help?
Do you have a question about the S Series B901 and is the answer not in the manual?
Questions and answers