Table of Contents
Advertisement
Quick Links
StreetWAVE™ SW-1000
Roadside Unit Installation
Copyright © Savari, Inc., 2017. All Rights Reserved. This publication, in whole or in part, may
not be reproduced, stored in a computerized, or other retrieval System or transmitted in any
form, or by any means whatsoever without the prior written permission from Savari, Inc.
Guide
2005 De La Cruz Boulevard #111,
Santa Clara, CA 95050
Release: RSU
Document Version: 1.2
Advertisement
Table of Contents
Related Manuals for Savari StreetWAVE SW-1000
Summary of Contents for Savari StreetWAVE SW-1000
- Page 1 Release: RSU Document Version: 1.2 Copyright © Savari, Inc., 2017. All Rights Reserved. This publication, in whole or in part, may not be reproduced, stored in a computerized, or other retrieval System or transmitted in any form, or by any means whatsoever without the prior written permission from Savari, Inc.
-
Page 2: Table Of Contents
Installing the Ground Cable ............................. 11 2.1.5 Installing the Lightning Surge Arrestors ......................12 2.1.6 Installing the Antennas.............................. 12 POST-INSTALLATION STEPS ........................14 WAVE™ ..........................14 OWERING N THE TREET UNINSTALLING THE STREETWAVE™ ....................15 Savari Inc., Confidential Copyright © Savari, Inc. 2017... -
Page 3: Introduction
1.1 Overview This guide explains how to install, maintain, uninstall, and troubleshoot your StreetWAVE™ Roadside Unit. For detailed instructions on using all the StreetWAVE™ features, refer to the Savari StreetWAVE™ Roadside Unit User Guide. 1.2 Audience This installation guide is created for the individuals installing Savari StreetWAVE™ Roadside Unit. -
Page 4: Prerequisites
Site surveys and designs are not part of the installation document. The Savari stock kit accessory will consist of the RSU mounting bracket. The choice of all other accessories is left to the customer. -
Page 5: Optional Components
5. Self sealing electrical tape: To further ensure that there is no water seepage into the antenna connectors 6. Lighting arrestor (Optional): Used to protect the RSU by preventing the rise in voltage when struck by lightning. Savari Inc., Confidential Copyright © Savari, Inc. 2017... -
Page 6: Mounting Kit
The mounting kit is made up of the mounting hardware, a metal strap and the sealing gland kit. The mounting hardware contains the following three (3) individual parts: 1. Universal Mounting Bracket [1 per RSU) part #SW-RSU-1KB Figure 2 Mounting Bracket Savari Inc., Confidential Copyright © Savari, Inc. 2017... - Page 7 The sealing gland kit consists of a seal nut, seal, seal body and gasket and its main aim is to provide a liquid-tight connection of the PoE cable to the Ethernet jack. Savari Inc., Confidential Copyright © Savari, Inc. 2017...
-
Page 8: Installing The Streetwave
Figure 6 Sealing Gland Kit 2 Installing the StreetWAVE™ The following section describes the procedure to install the Savari StreetWAVE™ device. 2.1.1 Installing the Mounting Bracket to the Pole The mounting bracket allows flexibility to install the RSU to a vertical or a horizontal mast. The bracket is attached to the RSU using the mounting bolt and the lock washer. -
Page 9: Installing The Mounting Bracket To The Rsu
RSU from moving or sliding. Tension ? 6. At the end of this step, the RSU, bracket and strap should resemble the illustration in Figure 8. Note that a vertical pole hasn’t been depicted here. Savari Inc., Confidential Copyright © Savari, Inc. 2017... -
Page 10: Installing The Poe Cable To The Rsu
5. Insert the RJ-45 cable connector into the Ethernet port receptacle of the RSU and ensure that the RJ-45 is locked into the internal RJ45 jack. 6. Slide the sealing gland kit towards the RSU and screw the threaded end into the RSU and hand-tighten. Savari Inc., Confidential Copyright © Savari, Inc. 2017... -
Page 11: Installing The Ground Cable
Figure 9 Exploded View of the Sealing Gland Installation 2.1.4 Installing the Ground Cable Savari recommends proper grounding to prevent damage to the RSU. The grounding point for the RSU is located on the side. The RSU consists of a ground screw that can be loosened to attach a ground wire. -
Page 12: Installing The Lightning Surge Arrestors
If an arrestor is used, the arrestor must be suitably grounded. Savari defers to the experience and accepted practice of the Operator with regards to the use of a lightning arrestor. - Page 13 SMA connector is found at the bottom of the enclosure. The operator may choose a magnetic mount antenna or an antenna with a separate mounting capability. When ordered, Savari typically supplies a magnetic mount GPS antenna with at least 1 meter RG-174 or equivalent cable.
-
Page 14: Post-Installation Steps
“Savari StreetWAVE™ Roadside Unit User Guide”. After powering on, the StreetWAVE™ device is ready to use. For information on using the different features of the device, refer to the Savari StreetWAVE™ Roadside Unit User Guide. Savari Inc., Confidential... -
Page 15: Uninstalling The Streetwave
4. Unscrew the Ethernet sealing assembly. 5. Using a small, standard screwdriver, depress the RJ-45 locking tab inside the Ethernet receptacle, and gently pull the cable to disconnect. 6. Hold the StreetWAVE™ and unscrew the mounting straps. Savari Inc., Confidential Copyright © Savari, Inc. 2017... - Page 16 CEP, 50%, 24 hours static – 2.0m with SBAS, 2.5m GPS* without assistance. Standards Compliance IEEE 802.11p, IEEE 1609.X, FIPS 140-2, US-DOT v4.1 RSU Specification. Security 1609.2, MAC, and SSL Enclosure IP66 rating, pole mount. * If Supplied by Savari...