Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Totem Manuals
  4. Robotics
  5. MINI SHOOTER
  6. Assembly manual

Totem MINI SHOOTER Assembly Manual

Motor-wheel platform with rubber band shooter
Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading

Related Manuals for Totem MINI SHOOTER

Summary of Contents for Totem MINI SHOOTER

  • Page 2: Part List

    1x Battery holder (3D) 1x Trigger gear (3D) 1x Hook (3D) 3x Cable clip 22x Rubber band 40mm 1x Mini battery 3,7V 1x Mini battery charger 1x Mini Control Board X3 1x Socket wrench (3D) 1x Hex key 2mm 1x Totem screwdriver...

  • Page 3: Battery Charging

    START WITH CHARGING THE BATTERY BATTERY CHARGING: Rechargeable battery must be charged by adult only. • The new battery pack needs to be charged before use. • Connect the USB charging cable to 5V USB power source, such as a laptop.
  • Page 4 Some of the nuts (~1%) are missing threads. This is a manufacturing issue. We are trying to minimize the fault. In the meantime, we supply extra nuts in your kit. We apologize for the in-convenience.
  • Page 5 You will need in this step: 1x Beam 11 cm 4x Nut M3 6x10 Pro tip: 1. Use the back of the screwdriver to push in the nuts. 2. After entering the first slot, nuts tend to tilt. Use your thumb to push it back straight, and then again use the screwdriver to insert the nut all the...
  • Page 6 2x Wheel bracket 2x Nut M3 6x10...
  • Page 7 1x Bolt M3x16 You can also use Beam/Bolt ruler to determine the length of beams and bolts...
  • Page 8 2x N20 motor bracket 2x N20 motor Position of the motor - cables down...
  • Page 9 1x Bolt M3x16...
  • Page 10 4x Wheel ring 2x 43mm O-shaft wheel 2x 43mm D-shaft wheel Make sure the rings sit tightly Up-side down...
  • Page 11 1x 43mm D-shaft wheel + 1x Nylon spacer 8mm Wheel ring...
  • Page 12 1x 43mm O-shaft wheel + 1x Nylon spacer 8mm 1x Shoulder bolt L8 M3x12 Wheel ring...
  • Page 13 2x Bolt M3x6 2x 2-hole simple bracket 1x Beam 11 cm 6x Nut M3 6x10...
  • Page 14 2x Bolt M3x6 1x Beam 11 cm 4x Nut M3 6x10...
  • Page 15 1x Bolt M3x6 1x L-twisted mirror bracket Step 10...
  • Page 16 1x Bolt M3x6 1x Mini servo motor with arm 1x Nut M3 6x10 Use Hex Key in this step...
  • Page 17 1x Bolt M3x6 1x L-twisted bracket...
  • Page 18 1x Bolt M3x6 1x Nut M3 6x10...
  • Page 19 1x Bolt M3x16 Make sure cable holder does not climb on the beam...
  • Page 20 1x Bolt M3x16 Position of cables...
  • Page 21 Use the Socket 1x Bolt M3x10 1x Strip bracket 1x Cap nut M3 Wrench (3D) to 45mm (9 holes) hold the Cap nut...
  • Page 22 1x 43mm D-shaft wheel + 1x Nylon spacer 8mm Wheel ring...
  • Page 23 1x 43mm O-shaft wheel + 1x Shoulder bolt L8 M3x12 1x Nylon spacer 8mm Wheel ring...
  • Page 24 2x Bolt M3x6 2x 2-hole simple bracket 1x Beam 5 cm 2x Nut M3 6x10...
  • Page 25 2x Bolt M3x6 2x Beam 11 cm 2x Nut M3 6x10...
  • Page 26 4x Bolt M3x6 4x Threaded spacer M3x8mm...
  • Page 27 2x Bolt M3x6 1x L-twisted mirror bracket 1x L-twisted bracket 1x Beam 7 cm 2x Nut M3 6x10...
  • Page 28 2x Bolt M3x6...
  • Page 29 2x Bolt M3x25...
  • Page 30 2x Bolt M3x25...
  • Page 31 1x Beam 11 cm 4x Nut M3 6x10...
  • Page 32 3x Bolt M3x6 1x Pistol left half 1x Pistol right half...
  • Page 33 1x Bolt M3x6 1x Trigger 1x Hook...
  • Page 34 1x Bolt M2.5x8 1x Trigger gear 1x Mini servo motor Turn the gear counterclockwise until it stops...
  • Page 35 2x Bolt M3x25 2x Nut M3 6x10 Small gap is OK...
  • Page 36 1x Bolt M3x25 1x Washer T2,5mm 1x Cap nut M3...
  • Page 37 1x Bolt M3x20 1x Cap nut M3...
  • Page 38 2x Rubber band 40mm...
  • Page 39 1x Bolt M3x6 1x Battery holder 1x Nut M3 6x10...
  • Page 40 2x Bolt M3x6 1x Mini Control Board X3 1x Nut M3 6x10...
  • Page 41 Pay attention to colors of the cables to plug them correctly...
  • Page 42 3x Cable clip (3D)
  • Page 43 Voilà! You have finished assembling the Mini Shooter. Load the rubber bands from the bottom to the top...

  • Page 44: How To Control

    HOW TO CONTROL Download the Totem app on your smartphone or tablet via App Store or Google Play. Search for: Totemmaker Or scan this code:...

  • Page 45: Troubleshoot

    Battery voltage is low. Charge the battery. (LEDs should blink). • Only one device can be connected to the Mini Shooter First LED of light bar is flashing when battery is at a time. Reconnect the battery to reset the electronics connected.

  • Page 46: Consumer Information

    PRECAUTIONS: ELECTRONICALLY OPERATED PRODUCT Do not give this product to children aged 8 or below. As with all electronic products, precautions should be observed during handling and use to prevent electric shock. Adult supervision required. CONSUMER INFORMATION Note to adults: to ensure that the child’s play is both safe and fun, please review all operating instructions and safety rules with your child. SAFETY WARNINGS: •...
  • Page 47 KEEP THIS INSTRUCTION MANUAL AND THE PRODUCT BOX AS IT CONTAIN IMPORTANT INFORMATION FOR FUTURE REFERENCE. Due to the continuous product improvement, the pictures on this manual may differ slightly from the actual product. Please adhere to actual product instead. Totem Maker names and logos are registered trademarks. All rights reserved. www.totemmaker.net Totem Technology, UAB Sauletekio al.