Page 2
Inserting nuts (1) Inserting nuts (2) Faulty threads Tightening Ruler standoffs It is a good idea to After entering the Totem Some of the nuts first slot, nuts tend start every step in- Wrench Socket are missing threads. to tilt. Use your...
Page 3
When starting on a building step, the 6mm bolts and 6x10 nuts are coloured RED. It makes it When a new Totem beam is needed in a step, easier to see where the new bolts and nuts are the length is indicated in centimeters.
Page 4
When it is helpful, the slot-number is indicated When a connection is a rotating hub, you must in the Totem beam. Starting from #1 and count- not tighten the bolt and nut too much. Test it for a ing slots.
Nylon Spacer 8mm 2-hole 45 simple Nylon Standoff Washer 1 mm Allen hex key Yellow DC motor 1:48 Yellow Wheel D 67mm M3x8mm Totem Wrench Socket 5 cm DIA24mm 3-5x 7 cm 10 cm ZIP Tie Li-Ion 3.7v Battery X3 Controller Board...
Page 6
PART 1 16 cm Bolt M3x6 Bolt M3x25 Nut M3 6x10 2-hole Simple Note: 2x 25mm Yellow DC motor 1:48 3 hole bracket 16 cm Note: This tap PART 1 to this side.
Page 12
Make sure that the 2 legs have a smooth rotation. If it is too tight, the function may fail because the servoes cannot manage to lift properly. Use the Totem Wrench Socket PART 4...
Page 13
PART 5 7 cm Use the Totem Wrench Socket Nut M3 6x10 Bolt M3x6 Nylon Standoff M3x8mm 2-hole 90 bracket 7 cm 10 cm...
Page 18
Don’t tighten the Bolt M3x8 Bolt M3x6 bolts too much. Make 10 mm sure there is smooth action. Not too wob- 40mm Use the Totem Bolt M3x10 Nut M3 6x10 bly, but also not too Wrench Socket 80mm tight. 10 mm...
Page 19
Register the servo arm. Be careful. A : Put on the servo arm assembly in any position. Don’t use too much force. Gen- tly twist it Coun- ter Clock-wise. B : Manually twist the arm Counter Clockwise until it stops.
Page 20
C : Temporarily take off the E : Attach the Servo Arm Index D : Slip on the Servo Arm Index servo arm. Disc on to the servo. Arrow on to the servo arm. H : Take off the disc and arrow. F : Put the Servo Arm with Index G : Here you can see the arrow Arrow back on the servo match-...
Page 22
Servo arm on the other side (arm B): Same proc edure as first servo. But the index mark is “K” position. Same as the oth- er side: Be careful. Don’t use too much force. Gen- tly twist it Coun- ter Clock-wise.
PART10 Cabling and connections. 3-5x ZIP Tie Integrated controller that has Bluetooth connection, 4 DC motor channels and 2 Servo motor channels. More info here: https://totemmaker.net/wiki/x3-fbi-board-set-up/...
Page 33
Note: Observe the wires orienta- tion: Brown, Red and Yellow. Building is finished ! Now it is time to test your model. PART 10...
HOW TO CONTROL Download Totem app on your smartphone or tablet via App Store or Google Play. To slow down the rotation speed, press two buttons at the same time. I. e. press both Forward and Right buttons. Follow the step by step guide to connect your...
PRECAUTIONS: ELECTRONICALLY OPERATED PRODUCT Do not give this product to children aged 8 or below. As with all electronic products, precautions should be observed during handling and use to prevent electric chock. Adult supervision required. Note to adults: to ensure that the child’s play is both safe and fun, please review all operating instructions and safety rules with your child. SAFETY WARNINGS: •...
KEEP THIS INTRUCTION MANUAL AND THE PRODUCT BOX AS IT CONTAIN IMPORTANT INFORMATION FOR FUTURE REFERENCE. Due to the continuous product improvement, the pictures on this manual may differ slightly from the actual product. Please adhere to actual product instead. Totem Maker names and logos are registered trademarks. All rights reserved. WARNING: www.totemmaker.net...