Do you have a question about the S-MIGMA-250.IGBT and is the answer not in the manual?
Questions and answers
Jesper
March 13, 2025
I **** looking for how to set up the welder for MIG and TIG welding ...?
The welding machine is a STAMOS S-MIGMA-250.IGBT
2 comments:
Mr. Anderson
March 13, 2025
The STAMOS S-MIGMA-250.IGBT welder supports MIG and TIG welding. Here’s how to set it up for each process:
MIG Welding Setup: 1. Connect the welder to a 230V power source. 2. Attach the MIG torch to the MIG output connection. 3. Connect the ground clamp to the workpiece. 4. Insert the appropriate MIG wire into the wire feeder. 5. Adjust the voltage and wire feed speed according to material thickness. 6. If using MAG welding, connect a shielding gas supply (e.g., CO2 or a gas mix). 7. Start welding by pulling the torch trigger.
TIG Welding Setup: 1. Connect the welder to a 230V power source. 2. Attach the TIG torch to the TIG output connection. 3. Connect the ground clamp to the workpiece. 4. Use a tungsten electrode suitable for the material. 5. Adjust the welding current settings according to the material. 6. If required, connect a shielding gas (e.g., argon). 7. Start welding by touching the electrode to the workpiece and lifting off.
Ensure all safety measures are in place before welding.
This answer is automatically generated
Jesper
March 13, 2025
... it was more in relation to gas pressure, wire speed and current strength ...?
Slobodan Ilic
April 7, 2025
Tauim ovaj deo moj Stamos S-MMA 250 IGBT
1 comments:
Mr. Anderson
May 14, 2025
The STAMOS S-MIGMA-250.IGBT is a 4-in-1 combined welding machine that supports MIG, MAG, MMA, WIG (TIG), and FCAW welding processes. It provides a welding current up to 250 A and includes features such as adjustable wire speed (2.5–13 m/min), inductance, and Hot Start. Its function is to perform various types of welding tasks using different welding methods.
U S E R M A N U A L 1.3 PERSONAL PROTECTION EQUIPMENT ELECTRIC ARC RADIATION CAN CAUSE DAMAGE TO EYES AND SKIN SYMBOLS • When welding, wear clean, oil stain free protective clothing made of non-flammable and non-conductive The operation manual must be read carefully.
• Chemical substances (lubricants, solvents) must be removed from the surfaces of welded objects as • Welders powered from a 3-Phase network are delivered without a plug, the plug must be obtained they burn and emit toxic smokes under the influence of temperature. independently and installation should be assigned to a qualified person.
Page 4
5. CABLE CONNECTIONS Function and description INSTRUCTIONS FOR CABLE CONNECTIONS: ERROR INDICATOR = The indicator lights in the following two situations: a) If the machine has malfunctioned and cannot be operated. MMA WELDING MODE b) If the cutting device has exceeded the standard working time, the protection mode is initiated Set the switch (6) to MMA welding mode.
NOTES/NOTIZEN 6. DISPOSING OF PACKAGING The various items used for packaging (cardboard, plastic straps, polyurethane foam) should be kept, so that the device can be sent back to the service centre in the best possible condition in case of any problems! 7.
Page 7
Umwelt – und Entsorgungshinweise Hersteller an Verbraucher Sehr geehrte Damen und Herren, gebrauchte Elektro – und Elektronikgeräte dürfen gemäß europäischer Vorgaben [1] nicht zum unsortierten Siedlungsabfall gegeben werden, sondern müssen getrennt erfasst werden. Das Symbol der Abfalltonne auf Rädern weist auf die Notwendigkeit der getrennten Sammlung hin.
Need help?
Do you have a question about the S-MIGMA-250.IGBT and is the answer not in the manual?
Questions and answers
I **** looking for how to set up the welder for MIG and TIG welding ...? The welding machine is a STAMOS S-MIGMA-250.IGBT
The STAMOS S-MIGMA-250.IGBT welder supports MIG and TIG welding. Here’s how to set it up for each process:
MIG Welding Setup:
1. Connect the welder to a 230V power source.
2. Attach the MIG torch to the MIG output connection.
3. Connect the ground clamp to the workpiece.
4. Insert the appropriate MIG wire into the wire feeder.
5. Adjust the voltage and wire feed speed according to material thickness.
6. If using MAG welding, connect a shielding gas supply (e.g., CO2 or a gas mix).
7. Start welding by pulling the torch trigger.
TIG Welding Setup:
1. Connect the welder to a 230V power source.
2. Attach the TIG torch to the TIG output connection.
3. Connect the ground clamp to the workpiece.
4. Use a tungsten electrode suitable for the material.
5. Adjust the welding current settings according to the material.
6. If required, connect a shielding gas (e.g., argon).
7. Start welding by touching the electrode to the workpiece and lifting off.
Ensure all safety measures are in place before welding.
This answer is automatically generated
... it was more in relation to gas pressure, wire speed and current strength ...?
Tauim ovaj deo moj Stamos S-MMA 250 IGBT
The STAMOS S-MIGMA-250.IGBT is a 4-in-1 combined welding machine that supports MIG, MAG, MMA, WIG (TIG), and FCAW welding processes. It provides a welding current up to 250 A and includes features such as adjustable wire speed (2.5–13 m/min), inductance, and Hot Start. Its function is to perform various types of welding tasks using different welding methods.
This answer is automatically generated